OpenBSC October 2023

openbsc@lists.osmocom.org

1 participants
14 discussions

dynamic traffic channels
by Neels Hofmeyr 20 May '25

20 May '25

On Tue, Jun 28, 2016 at 10:05:28AM +0200, Harald Welte wrote: > [translated from german] > is it certain that we switch a channel to PDCH only when > gprs mode != none? A TS can be GSM_PCHAN_TCH_F_PDCH; those are the only ones for which we send a PDCH ACT message. We send a PDCH ACT message - during init (CHANNEL OML's state changed to enabled -> send PDCH ACT), - and upon channel release ack when pchan == GSM_PCHAN_TCH_F_PDCH. So the question is, when we receive a channel release ack, could that be the PDCH release and we switch PDCH right back on by accident? No, because we only receive a chan rel ack when the *TCH/F* is being released. That is because the PDCH release is initiated "internally" from the PDCH DEACT, and thus this condition in common/rsl.c rsl_tx_rf_rel_ack() catches on, which existed before dyn PDCH: if (lchan->rel_act_kind != LCHAN_REL_ACT_RSL) { LOGP(DRSL, LOGL_NOTICE, "%s not sending REL ACK\n", gsm_lchan_name(lchan)); return 0; } In rsl_rx_rf_chan_rel() the rel_act_kind is set to LCHAN_REL_ACT_RSL, but not in the rsl_rx_dyn_pdch(). This is analogous to the ip.access way -- the ip.access nanobts replies to a PDCH DEACT with a PDCH DEACT ACK and doesn't send a separate channel release ack. Maybe we could set rel_act_kind to some new LCHAN_REL_ACT_IPAC_DYN_PDCH for clarity? (But we shouldn't actually send a release ack, to stay compatible.) Even though it works as-is, we should indeed add another flag check: - We do check the flags that no ACT/DEACT is already pending; - And we do send a PDCH DEACT only if ts->flags & TS_F_PDCH_ACTIVE; - But we would send a PDCH ACT despite ts->flags & TS_F_PDCH_ACTIVE. This should never happen, but it would make sense to ensure that. ~Neels

3 5

libosmocore/BSC/MSC: MO voice calls rejected from Siemens S11E (patch included)
by Lennart Müller 31 Jan '24

31 Jan '24

Hi, I had a problem placing MO GSM calls from a Siemens S11E: The calls were dropped immediately; Osmo-MSC reports "Cannot compose Channel Type from bearer capabilities" After investigating the SETUP request from the S11E, the phone does not use octet 3a (no extension bit set in IE 3). Wireshark decodes the radio channel requirement as "Full rate support only MS/fullrate speech version 1 supported", so I added a condition to the gsm48_ie.c function of libosmocore to include at least GSM FR in the list of available speech_ver in case octet 3 has no extension. Attached to this message are the Abis-IP PCAP traces of MO calls, and the patch for gsm48_ie.c. Regards, Lennart

6 6

Problem while running NIB on Open Cellular Base sation
by Brackley Casinga 31 Jan '24

31 Jan '24

Hi, My name is Brackley Cassinga Form DRC, we run a community network called pamoja net where we offer gsm services using osmocom open source software and OC Base station. Recently I have tried to install another base station as the same installed but I could not find any resource guiding through all the steps to take to run NIB on a base station. I'm currently running Ubuntu and I will appreciate if you could guide me on the installation of BSC,hlr,MSC , in order to run a basic gsm network. Thank you. Regards -- *Ir Brackley heshima Casinga **Pacifique* *CEO and Founder of kwanzatechnologie* KwanzaTechnologies ,GlobalElectronics +243977265291 | +243977265291 | Pcassinga(a)gmail.com/ brackley(a)ensemblepourladifference.org www.kwantechnologies.jimdosite.com <http://www.kwantechnologies.com/> | Skype: Brackley cassinga <https://webapp.wisestamp.com/#> Av Semliki N 43

2 1

Network communication equipments for inquiry <16/10/2023 17:55>
by Yolanda from Longriseequipment 16 Oct '23

16 Oct '23

1 0

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

OpenBSC October 2023