hello
to enable handover function, do i have to change in data field msg_3 the corresponding values form 0x00h to 0x01h?
does 0x01h enable where 0x00h disables?
T.
From: Pablo Neira Ayuso <pablo(a)gnumonks.org>
This patchset is the first in the series to cleanup redundant code
in ipaccess tools.
They are available in the pablo/cleanups branch in openbsc git tree.
Please, merge it!
Thanks.
Pablo Neira Ayuso (3):
ipaccess-config: exit if no network interface is specified
libcommon: socket: extend make_sock() prototype
ipaccess-proxy: get rid of internal make_sock() implementation
openbsc/include/openbsc/socket.h | 5 ++-
openbsc/src/ipaccess/ipaccess-find.c | 1 +
openbsc/src/ipaccess/ipaccess-proxy.c | 42 ++------------------------------
openbsc/src/libabis/input/hsl.c | 4 +-
openbsc/src/libabis/input/ipaccess.c | 8 +++---
openbsc/src/libcommon/socket.c | 10 ++++---
openbsc/src/libgb/gprs_ns.c | 2 +-
openbsc/src/libgb/gprs_ns_frgre.c | 2 +-
openbsc/src/osmo-bsc_nat/bsc_ussd.c | 2 +-
9 files changed, 22 insertions(+), 54 deletions(-)
--
1.7.2.3
Hi all,
A thread on the asterisk mailing list re-triggerd my memory.
Last november or so i asked if it might be possible to use a
gsm/umts-dongle as a bts. afaicr the general consensus was that it was
not possible because the proximity of TX and RX hardware.
I have been discussing it with my colleges today and wonder where we
were making the obvious thinking-mistake...
1) i know, that certainly at higher powers, the receiver becomes deaf in
the vincinity of a (high powered) transmitter, due to cirtuit overload,
but in our case we only needs a single miliwatt or even less....
2) scanning for multiple devices/frequencies is not needed.
[the idea is to connect to a single hand-held-device, that is only one
meter away, and feed voice through an existing IP-connection]
3) if a dongle is not usable for above reasons as a BTS, why is that
same dongle (more-or-less) capable as working as a handheld? Same
problems should occur as such, not?
http://wiki.e1550.mobi/doku.php
If they can tap in the device for audio/sms-client, it should also be
possible to do it the other way round, as a single-thread bts....
still puzzled, Hans
Hi, list!
I'm trying to understand how the options "nominal power" and
"max_power_red" work...
Last Friday I tried to place 4 BTS in a rectangle of about 100x20 meter
and then I examined the measurement reports of a mobile. They are very
very bad, and oft it cannot see a cell.
Then I tried to change the value of "nominal power" (max_power_red did
not changed) and retry to check the measurement reports.
No changes... :(
Now I'm here in my office with a spectrum analyzer and try to change
these values, but what I see in the spectrum analyzer is always the
same...
I restart OpenBSC after any change, of course!
Could you please help me to understand what these values mean and how
can I boost the signal?
Thanks a lot in advance for your help!
--
_______________________________________________________________________
Luca Bertoncello
Entwicklung Mail: bertoncello(a)netzing.de
NETZING Solutions AG Tel.: 0351/41381 - 23
Fröbelstr. 57, 01159 Dresden Fax: 0351/41381 - 12
_______________________________________________________________________
Impressum:
NETZING Solutions AG - Fröbelstraße 57 - 01159 Dresden
Sitz der Gesellschaft Amtsgericht Dresden HRB 18926
Vorstand Dieter Schneider - Aufsichtsratsvorsitzender Volker Kanitz
USt.Id DE211326547 Mail: netzing.ag(a)netzing.de
