- OpenBSC - lists.osmocom.org

Motorola Mo-bis / Implications for CCC Camp
by Harald Welte 19 Jun '11

19 Jun '11

Hi all, it seems like supporting the Motorola BTS from OpenBSC is a really big challenge. Not only are there problems regarding an unknown configuration database format (see http://laforge.gnumonks.org/weblog/2011/06/18/) Dieter has found the following excellent document, which in Chapter 5 describes the architecture of the Motorola specific changes to A-bis: http://read.pudn.com/downloads61/ebook/212957/SYS01.pdf Judging from the document: * there is an unknown 'motorola executive header' in front of RSL * many RSL standard messages have been replaced by proprietary ones * they use a mixture of 08.08 (A) and 08.58 (A-bis) information elements * many features normally found in the BSC are implemented in the BTS, e.g. the entire CHAN RQD / RSL CHAN ACT / IMM ASS CMD sequence is done fully inside the BTS. As a result, I think it will be a quite complex project to support those BTSs from OpenBSC. It's not just a matter of adding some small vendor-specific OML messages like with Siemens, Ericsson and ip.access. While it might still be interesting, I think it's unrealistic to assume this would happen ahead of the camp [unless somebody finds a compatible Motorola BSC that they can borrow us for analysis + protocol tracing]. Thus, the focus for the 2011 CCC Camp is now back to ip.access. The main issues we will be facing is on the RF side, i.e. * RF PA for the TX side * combining the PA outputs to be transmitted on one antenna * filter + LNA for Rx side * splitting the Rx signal As indicated previously, I would love to see something like two BTS with three TRX each. If we'd recycle the duplexer/combiner blocks from the Motorola BTS, we could do something like three sites with 2 TRX each. (as they can only combine two TRX). We _might_ also be able to re-cycle the TX PA from the Motorola CTUs, at least on the RF side it would be pretty easy to drive them from a nanoBTS rather than its internal source (as there's a connector). The bigger question is how do we get the controller logic of the PA into a state that the PA is actually enabled and active... Regards, Harald -- - Harald Welte <laforge(a)gnumonks.org> http://laforge.gnumonks.org/ ============================================================================ "Privacy in residential applications is a desirable marketing option." (ETSI EN 300 175-7 Ch. A6)

1 0

Problems during initial bring-up of nanoBTS
by Harald Welte 19 Jun '11

19 Jun '11

Hi zecke and others, I may have found a cause of one of the problems that we've been experiencing in nanoBTS bring-up, at least at some point in the past. The problem could be observed/described as: During the first OML connect of the nanoBTS, OpenBSC fails to bring it up completely. Second and successive connects worked fine. What I have just noticed is that we never re-set the NM state information for the 12.21 MOs inside OpenBSC. This means, if the A-bis link is lost, the old state information continues to exist. I guess it would be cleaner to simply re-set all the nm_state strucures that are part of the 'struct gsm_bts', gsm_bts_trx, etc. when the A-bis link is lost. As I'm working in this area right now anyway, I intend to produce a patch addressing the issue. But now that I think more about it: I guess it is unrelated to the old problem, as a typical work-around was to re-start OpenBSC, at which time all state is re-set again. Regards, Harald -- - Harald Welte <laforge(a)gnumonks.org> http://laforge.gnumonks.org/ ============================================================================ "Privacy in residential applications is a desirable marketing option." (ETSI EN 300 175-7 Ch. A6)

1 0

Help me! How to buy nanobts or hsl 2.75g picocell ??
by 高品章 19 Jun '11

19 Jun '11

Dear all, I want to buy some nanoBTS or HSL 2.75G picocell . Is there any body who wants to sell nanoBTS or HSL 2.75G picocell ? Looking forward for any offer . Regards, 　　　　　　　　jngpz(a)163.com 　　　　　　　　　　2011-06-19

1 0

Serial console on FemtoCell
by Bthomas 15 Jun '11

15 Jun '11

Dear Developers, I mentioned earlier that I found a tutorial in which we read that this cell is within the box's serial port. I found him looking for a RS485 port outlet, and 2x5-pin lines of pins. Images from the PCB: http://www.facebook.com/media/set/?set=a.1979958333026.114473.1065188491 IPSEC have read so far by launching tube through a communication gateway through which to get "home location register" information, etc.. Whether there is a chance to even download the firmware via the serial terminal analysis? Or perhaps to be found in lines of pins USB option? The presentation referred to the serial port connection just yet to start when you press the reset button four times, then the boot menu to configure the IP address, login data. greetings: bthomyka

2 1

Linux based 3g picocell sourcecode - vodafone rebranded
by Bthomas 14 Jun '11

14 Jun '11

Dear OpenBSC Developers! Although I can not help much in development, but once you split a link which is available in a 3G pico(?)cell rebranded by vodafone firmware. link: https://forge.betavine.net/frs/download.php/650/foss_fbsr-02.01.51.46.tar.gz sincerely bthomyka

2 1

[PATCH] socket: add OSMO_SOCK_F_[CONNECT|BIND|NON_BLOCK] flags
by Pablo Neira Ayuso 13 Jun '11

13 Jun '11

From: Pablo Neira Ayuso <pablo(a)gnumonks.org> This extends the socket infrastructure in libosmocore to allow to create non-blocking sockets. Basically, it replaces the connect0_bind1 parameter by one flags parameter. --- include/osmocom/core/socket.h | 11 ++++++++--- src/gsmtap_util.c | 6 ++++-- src/socket.c | 38 ++++++++++++++++++++++++++++---------- 3 files changed, 40 insertions(+), 15 deletions(-) diff --git a/include/osmocom/core/socket.h b/include/osmocom/core/socket.h index b2601c7..612b12c 100644 --- a/include/osmocom/core/socket.h +++ b/include/osmocom/core/socket.h @@ -5,14 +5,19 @@ struct sockaddr; +/* flags for osmo_sock_init. */ +#define OSMO_SOCK_F_CONNECT (1 << 0) +#define OSMO_SOCK_F_BIND (1 << 1) +#define OSMO_SOCK_F_NONBLOCK (1 << 2) + int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, - const char *host, uint16_t port, int connect0_bind1); + const char *host, uint16_t port, unsigned int flags); int osmo_sock_init_ofd(struct osmo_fd *ofd, int family, int type, int proto, - const char *host, uint16_t port, int connect0_bind1); + const char *host, uint16_t port, unsigned int flags); int osmo_sock_init_sa(struct sockaddr *ss, uint16_t type, - uint8_t proto, int connect0_bind1); + uint8_t proto, unsigned int flags); /* determine if the given address is a local address */ int osmo_sockaddr_is_local(struct sockaddr *addr, unsigned int addrlen); diff --git a/src/gsmtap_util.c b/src/gsmtap_util.c index eddde04..47fa37d 100644 --- a/src/gsmtap_util.c +++ b/src/gsmtap_util.c @@ -124,7 +124,8 @@ int gsmtap_source_init_fd(const char *host, uint16_t port) if (host == NULL) host = "localhost"; - return osmo_sock_init(AF_UNSPEC, SOCK_DGRAM, IPPROTO_UDP, host, port, 0); + return osmo_sock_init(AF_UNSPEC, SOCK_DGRAM, IPPROTO_UDP, host, port, + OSMO_SOCK_F_CONNECT); } int gsmtap_source_add_sink_fd(int gsmtap_fd) @@ -138,7 +139,8 @@ int gsmtap_source_add_sink_fd(int gsmtap_fd) return rc; if (osmo_sockaddr_is_local((struct sockaddr *)&ss, ss_len) == 1) { - rc = osmo_sock_init_sa((struct sockaddr *)&ss, SOCK_DGRAM, IPPROTO_UDP, 1); + rc = osmo_sock_init_sa((struct sockaddr *)&ss, SOCK_DGRAM, + IPPROTO_UDP, OSMO_SOCK_F_BIND); if (rc >= 0) return rc; } diff --git a/src/socket.c b/src/socket.c index 0be98b9..f1fcccd 100644 --- a/src/socket.c +++ b/src/socket.c @@ -6,6 +6,7 @@ #include <osmocom/core/select.h> #include <osmocom/core/socket.h> +#include <sys/ioctl.h> #include <sys/socket.h> #include <sys/types.h> @@ -18,12 +19,16 @@ #include <ifaddrs.h> int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, - const char *host, uint16_t port, int connect0_bind1) + const char *host, uint16_t port, unsigned int flags) { struct addrinfo hints, *result, *rp; int sfd, rc, on = 1; char portbuf[16]; + if ((flags & (OSMO_SOCK_F_BIND | OSMO_SOCK_F_CONNECT)) == + (OSMO_SOCK_F_BIND | OSMO_SOCK_F_CONNECT)) + return -EINVAL; + sprintf(portbuf, "%u", port); memset(&hints, 0, sizeof(struct addrinfo)); hints.ai_family = family; @@ -31,7 +36,7 @@ int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, hints.ai_flags = 0; hints.ai_protocol = proto; - if (connect0_bind1) + if (flags & OSMO_SOCK_F_BIND) hints.ai_flags |= AI_PASSIVE; rc = getaddrinfo(host, portbuf, &hints, &result); @@ -44,10 +49,24 @@ int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, sfd = socket(rp->ai_family, rp->ai_socktype, rp->ai_protocol); if (sfd == -1) continue; - if (connect0_bind1 == 0) { - if (connect(sfd, rp->ai_addr, rp->ai_addrlen) != -1) + if (flags & OSMO_SOCK_F_NONBLOCK) { + if (ioctl(sfd, FIONBIO, (unsigned char *)&on) < 0) { + perror("cannot set this socket unblocking"); + close(sfd); + return -EINVAL; + } + } + if (flags & OSMO_SOCK_F_CONNECT) { + rc = connect(sfd, rp->ai_addr, rp->ai_addrlen); + if (rc != -1 || (rc == -1 && errno == EINPROGRESS)) break; } else { + rc = setsockopt(sfd, SOL_SOCKET, SO_REUSEADDR, + &on, sizeof(on)); + if (rc < 0) { + perror("cannot setsockopt socket"); + break; + } if (bind(sfd, rp->ai_addr, rp->ai_addrlen) != -1) break; } @@ -63,7 +82,7 @@ int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, setsockopt(sfd, SOL_SOCKET, SO_REUSEADDR, &on, sizeof(on)); /* Make sure to call 'listen' on a bound, connection-oriented sock */ - if (connect0_bind1 == 1) { + if (flags & OSMO_SOCK_F_BIND) { switch (type) { case SOCK_STREAM: case SOCK_SEQPACKET: @@ -75,11 +94,11 @@ int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, } int osmo_sock_init_ofd(struct osmo_fd *ofd, int family, int type, int proto, - const char *host, uint16_t port, int connect0_bind1) + const char *host, uint16_t port, unsigned int flags) { int sfd, rc; - sfd = osmo_sock_init(family, type, proto, host, port, connect0_bind1); + sfd = osmo_sock_init(family, type, proto, host, port, flags); if (sfd < 0) return sfd; @@ -96,7 +115,7 @@ int osmo_sock_init_ofd(struct osmo_fd *ofd, int family, int type, int proto, } int osmo_sock_init_sa(struct sockaddr *ss, uint16_t type, - uint8_t proto, int connect0_bind1) + uint8_t proto, unsigned int flags) { char host[NI_MAXHOST]; uint16_t port; @@ -127,8 +146,7 @@ int osmo_sock_init_sa(struct sockaddr *ss, uint16_t type, return s; } - return osmo_sock_init(ss->sa_family, type, proto, host, - port, connect0_bind1); + return osmo_sock_init(ss->sa_family, type, proto, host, port, flags); } static int sockaddr_equal(const struct sockaddr *a,

3 2

[PATCH] socket: extend infrastructure to support non-blocking sockets
by Pablo Neira Ayuso 12 Jun '11

12 Jun '11

From: Pablo Neira Ayuso <pablo(a)gnumonks.org> * add OSMO_SOCK_F_[CONNECT|BIND|NON_BLOCK] flags * osmo_sock_connect() to call connect once the non-blocking connect becomes ready. This extends the socket infrastructure in libosmocore to allow to create non-blocking sockets. Basically, it replaces the connect0_bind1 parameter by one flags parameter. --- include/osmocom/core/socket.h | 11 ++++++++--- src/gsmtap_util.c | 6 ++++-- src/socket.c | 38 ++++++++++++++++++++++++++++---------- 3 files changed, 40 insertions(+), 15 deletions(-) diff --git a/include/osmocom/core/socket.h b/include/osmocom/core/socket.h index b2601c7..612b12c 100644 --- a/include/osmocom/core/socket.h +++ b/include/osmocom/core/socket.h @@ -5,14 +5,19 @@ struct sockaddr; +/* flags for osmo_sock_init. */ +#define OSMO_SOCK_F_CONNECT (1 << 0) +#define OSMO_SOCK_F_BIND (1 << 1) +#define OSMO_SOCK_F_NONBLOCK (1 << 2) + int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, - const char *host, uint16_t port, int connect0_bind1); + const char *host, uint16_t port, unsigned int flags); int osmo_sock_init_ofd(struct osmo_fd *ofd, int family, int type, int proto, - const char *host, uint16_t port, int connect0_bind1); + const char *host, uint16_t port, unsigned int flags); int osmo_sock_init_sa(struct sockaddr *ss, uint16_t type, - uint8_t proto, int connect0_bind1); + uint8_t proto, unsigned int flags); /* determine if the given address is a local address */ int osmo_sockaddr_is_local(struct sockaddr *addr, unsigned int addrlen); diff --git a/src/gsmtap_util.c b/src/gsmtap_util.c index eddde04..47fa37d 100644 --- a/src/gsmtap_util.c +++ b/src/gsmtap_util.c @@ -124,7 +124,8 @@ int gsmtap_source_init_fd(const char *host, uint16_t port) if (host == NULL) host = "localhost"; - return osmo_sock_init(AF_UNSPEC, SOCK_DGRAM, IPPROTO_UDP, host, port, 0); + return osmo_sock_init(AF_UNSPEC, SOCK_DGRAM, IPPROTO_UDP, host, port, + OSMO_SOCK_F_CONNECT); } int gsmtap_source_add_sink_fd(int gsmtap_fd) @@ -138,7 +139,8 @@ int gsmtap_source_add_sink_fd(int gsmtap_fd) return rc; if (osmo_sockaddr_is_local((struct sockaddr *)&ss, ss_len) == 1) { - rc = osmo_sock_init_sa((struct sockaddr *)&ss, SOCK_DGRAM, IPPROTO_UDP, 1); + rc = osmo_sock_init_sa((struct sockaddr *)&ss, SOCK_DGRAM, + IPPROTO_UDP, OSMO_SOCK_F_BIND); if (rc >= 0) return rc; } diff --git a/src/socket.c b/src/socket.c index 0be98b9..f1fcccd 100644 --- a/src/socket.c +++ b/src/socket.c @@ -6,6 +6,7 @@ #include <osmocom/core/select.h> #include <osmocom/core/socket.h> +#include <sys/ioctl.h> #include <sys/socket.h> #include <sys/types.h> @@ -18,12 +19,16 @@ #include <ifaddrs.h> int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, - const char *host, uint16_t port, int connect0_bind1) + const char *host, uint16_t port, unsigned int flags) { struct addrinfo hints, *result, *rp; int sfd, rc, on = 1; char portbuf[16]; + if ((flags & (OSMO_SOCK_F_BIND | OSMO_SOCK_F_CONNECT)) == + (OSMO_SOCK_F_BIND | OSMO_SOCK_F_CONNECT)) + return -EINVAL; + sprintf(portbuf, "%u", port); memset(&hints, 0, sizeof(struct addrinfo)); hints.ai_family = family; @@ -31,7 +36,7 @@ int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, hints.ai_flags = 0; hints.ai_protocol = proto; - if (connect0_bind1) + if (flags & OSMO_SOCK_F_BIND) hints.ai_flags |= AI_PASSIVE; rc = getaddrinfo(host, portbuf, &hints, &result); @@ -44,10 +49,24 @@ int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, sfd = socket(rp->ai_family, rp->ai_socktype, rp->ai_protocol); if (sfd == -1) continue; - if (connect0_bind1 == 0) { - if (connect(sfd, rp->ai_addr, rp->ai_addrlen) != -1) + if (flags & OSMO_SOCK_F_NONBLOCK) { + if (ioctl(sfd, FIONBIO, (unsigned char *)&on) < 0) { + perror("cannot set this socket unblocking"); + close(sfd); + return -EINVAL; + } + } + if (flags & OSMO_SOCK_F_CONNECT) { + rc = connect(sfd, rp->ai_addr, rp->ai_addrlen); + if (rc != -1 || (rc == -1 && errno == EINPROGRESS)) break; } else { + rc = setsockopt(sfd, SOL_SOCKET, SO_REUSEADDR, + &on, sizeof(on)); + if (rc < 0) { + perror("cannot setsockopt socket"); + break; + } if (bind(sfd, rp->ai_addr, rp->ai_addrlen) != -1) break; } @@ -63,7 +82,7 @@ int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, setsockopt(sfd, SOL_SOCKET, SO_REUSEADDR, &on, sizeof(on)); /* Make sure to call 'listen' on a bound, connection-oriented sock */ - if (connect0_bind1 == 1) { + if (flags & OSMO_SOCK_F_BIND) { switch (type) { case SOCK_STREAM: case SOCK_SEQPACKET: @@ -75,11 +94,11 @@ int osmo_sock_init(uint16_t family, uint16_t type, uint8_t proto, } int osmo_sock_init_ofd(struct osmo_fd *ofd, int family, int type, int proto, - const char *host, uint16_t port, int connect0_bind1) + const char *host, uint16_t port, unsigned int flags) { int sfd, rc; - sfd = osmo_sock_init(family, type, proto, host, port, connect0_bind1); + sfd = osmo_sock_init(family, type, proto, host, port, flags); if (sfd < 0) return sfd; @@ -96,7 +115,7 @@ int osmo_sock_init_ofd(struct osmo_fd *ofd, int family, int type, int proto, } int osmo_sock_init_sa(struct sockaddr *ss, uint16_t type, - uint8_t proto, int connect0_bind1) + uint8_t proto, unsigned int flags) { char host[NI_MAXHOST]; uint16_t port; @@ -127,8 +146,7 @@ int osmo_sock_init_sa(struct sockaddr *ss, uint16_t type, return s; } - return osmo_sock_init(ss->sa_family, type, proto, host, - port, connect0_bind1); + return osmo_sock_init(ss->sa_family, type, proto, host, port, flags); } static int sockaddr_equal(const struct sockaddr *a,

2 1

huawei uap 3801e
by Bthomas 10 Jun '11

10 Jun '11

Dear Developers! Currently, the only tool I have found this information: http://users.atw.hu/helvei/UAP3801E.rar?atw_referer=http% 3A% 2F% 2Fmobil- telefon.vatera.hu 2Fmobiltelefon_tartozek%%% 2Fegyeb 2F4_db_huawei_ap_femtocella_mobil_bazisallomas_1459406466.html This is a power point presentation, the pages visible to a certain set of procedures. Although I do not know how much help in the development, but I share with you. Consulted during a programmer who is interested in finding a "reverse engineering" and curious about the possibility of the device, the communication. I am confident that if he succeeds, much of the project promotes the development of OpenBSC. Regards, bthomyka

1 0

Re: SGSN Crash
by Holger Hans Peter Freyther 10 Jun '11

10 Jun '11

On 05/30/2011 06:27 AM, Seungju Kim wrote: > Hello, I am experiencing some crash with osmo-sgsn. > This is the log : http://pastebin.com/XP8RcaaNI didnt make any modification except removing imsi roaming check. > Every time when a phone tries to connect this happens. What might be wrong? Hi, please make yourself gdb and git and create a patch. The struct msgb has detected a mis-use and forced a crash. What is going wrong is in the log, you will need to identify where this msgb got allocated (or change the panic message to print the name of the msgb) and see why it is using the amount of headroom it wants to use. happy hacking holger

3 6

huawei uap 3801e
by Bthomas 09 Jun '11

09 Jun '11

Dear OpenBSC users and developers! I beseech you, help me with some information. Today I bought a 4 pack auction Huawei femtocell UAP 3801. Next to them there's no documentation, Huawei has not yet responded to my questions. I want them to operate with OpenBSC. Do you think this tool will work with it? If anyone are having operating instructions, configuration instructions, please share it with me. Thanks, bthomyka

2 1