hello, built 2 bs11 interconnect cables + termination today. but the second bs11's not recongnised. i tried the 2-2 cfg-file, and mine. i want to use only one trx per bts. my cfg-file look like this: ! ! OpenBSC configuration saved from vty ! ! password foo ! line vty no login ! network network country code 262 mobile network code 10 short name T-Net long name Test-Netz timer t3101 10 timer t3113 60 bts 0 type bs11 band GSM900 cell_identity 1 location_area_code 1 training_sequence_code 7 base_station_id_code 63 oml e1 line 0 timeslot 1 sub-slot full oml e1 tei 25 trx 0 arfcn 121 max_power_red 0 rsl e1 line 0 timeslot 1 sub-slot full rsl e1 tei 1 timeslot 0 phys_chan_config CCCH+SDCCH4 e1 line 0 timeslot 1 sub-slot full timeslot 1 phys_chan_config TCH/F e1 line 0 timeslot 2 sub-slot 1 timeslot 2 phys_chan_config TCH/F e1 line 0 timeslot 2 sub-slot 2 timeslot 3 phys_chan_config TCH/F e1 line 0 timeslot 2 sub-slot 3 timeslot 4 phys_chan_config TCH/F e1 line 0 timeslot 3 sub-slot 0 timeslot 5 phys_chan_config TCH/F e1 line 0 timeslot 3 sub-slot 1 timeslot 6 phys_chan_config TCH/F e1 line 0 timeslot 3 sub-slot 2 timeslot 7 phys_chan_config TCH/F e1 line 0 timeslot 3 sub-slot 3 bts 1 type bs11 band GSM900 location_area_code 2 training_sequence_code 7 base_station_id_code 63 oml e1 line 1 timeslot 4 sub-slot full oml e1 tei 25 trx 0 arfcn 122 max_power_red 0 rsl e1 line 1 timeslot 4 sub-slot full rsl e1 tei 1 timeslot 0 phys_chan_config CCCH+SDCCH4 e1 line 1 timeslot 5 sub-slot 0 timeslot 1 phys_chan_config SDCCH8 e1 line 1 timeslot 5 sub-slot 1 timeslot 2 phys_chan_config TCH/F e1 line 1 timeslot 5 sub-slot 2 timeslot 3 phys_chan_config TCH/F e1 line 1 timeslot 5 sub-slot 3 timeslot 4 phys_chan_config TCH/F e1 line 1 timeslot 6 sub-slot 0 timeslot 5 phys_chan_config TCH/F e1 line 1 timeslot 6 sub-slot 1 timeslot 6 phys_chan_config TCH/F e1 line 1 timeslot 6 sub-slot 2 timeslot 7 phys_chan_config TCH/F e1 line 1 timeslot 6 sub-slot 3 i modified the 2-2 cfg file in a way that made sense to me. when i connect only the 2nd bs11 to the pc, it isnt recognised as well. firmware is on, an due to people who works there, this bs11 was once operational. did i forget any setup procedures maybe? 2nd problem: bs11_config i tried bs11_config -p /dev/ttyUSB0 as described in the page, but seems this device ttyUSB0 doesnt exist.the lmt cable is connected and telnet localhost 4242 from other console also works. 3rd problem: during bsc_hack running, i get strange messages. my 2 favorites are: gsm04_08.c: 873 location updating reject on channel 0 abis_nm.c:1799 Invalid channel combination!! is there any faq or something else, where these messages are explanined? answers in german preferred. increases enormously the readability on my pc. T. -- Wer Rechtschreibfehler findet, darf sie behalten!