Limesdr mini and nightly builds....

Hi, I have just received a limesdr mini, and I am trying to get that sdr to the same level as I had with uhd B100. I managed to get the whole config working properly, but stability was bad, as you have read. As I was recommended, I have been runnig "nightly" binaries, and see where I end up.... :-) limesdr installed in Orange Pi Zero, (armhf). Limesuite 18.10.0-1, LimeUtil seems happy, and I can see the SDR However, I cannot get stability enough to get a stable signal.... Gullik TRX LIME CONFIG log stderr  logging filter all 1  logging color 1  logging print category 1  logging timestamp 1  logging print file basename  logging level set-all info ! line vty  no login ! trx  bind-ip 127.0.0.1  remote-ip 127.0.0.1  base-port 5700  egprs disable  tx-sps 4  rx-sps 4  rt-prio 18  chan 0   tx-path BAND1   rx-path LNAW bsc 1.3.0.287 or .284 will not run, fails with error in sysmalloc(), so I try running .283, from dec 19.... maybe this problem is armhf related...?? this is the bsc config...... osmobsc config file ! osmo-bsc default configuration ! (assumes STP to run on 127.0.0.1 and uses default point codes) ! e1_input  e1_line 0 driver ipa network  network country code 1  mobile network code 1  encryption a5 0  neci 1  paging any use tch 0  handover 0  handover algorithm 1  handover1 window rxlev averaging 10  handover1 window rxqual averaging 1  handover1 window rxlev neighbor averaging 10  handover1 power budget interval 6  handover1 power budget hysteresis 3  handover1 maximum distance 9999  dyn_ts_allow_tch_f 0  periodic location update 30  bts 0   type sysmobts   band DCS1800   cell_identity 0   location_area_code 1   base_station_id_code 63   ms max power 15   cell reselection hysteresis 4   rxlev access min 0   radio-link-timeout 32   channel allocator ascending   rach tx integer 9   rach max transmission 7   channel-descrption attach 1   channel-descrption bs-pa-mfrms 5   channel-descrption bs-ag-blks-res 1   early-classmark-sending forbidden   ip.access unit_id 1801 0   oml ip.access stream_id 255 line 0   codec-support fr   gprs mode none   trx 0    rf_locked 0    arfcn 871    nominal power 20    ! to use full TRX power, set max_power_red 0    max_power_red 3    rsl e1 tei 0    timeslot 0     phys_chan_config CCCH+SDCCH4     hopping enabled 0    timeslot 1     phys_chan_config TCH/F     hopping enabled 0    timeslot 2     phys_chan_config TCH/F     hopping enabled 0    timeslot 3     phys_chan_config TCH/F     hopping enabled 0    timeslot 4     phys_chan_config TCH/F     hopping enabled 0    timeslot 5     phys_chan_config TCH/F     hopping enabled 0    timeslot 6     phys_chan_config TCH/F     hopping enabled 0    timeslot 7     phys_chan_config TCH/F     hopping enabled 0 msc 0  no bsc-welcome-text  no bsc-msc-lost-text  no bsc-grace-text  type normal  allow-emergency allow  amr-config 12_2k forbidden  amr-config 10_2k forbidden  amr-config 7_95k forbidden  amr-config 7_40k forbidden  amr-config 6_70k forbidden  amr-config 5_90k allowed  amr-config 5_15k forbidden  amr-config 4_75k forbidden  codec-list fr1 fr2 fr3 hr1 hr3  mgw remote-ip 127.0.0.1  mgw remote-port 2427  mgw local-port 2727  mgw endpoint-range 1 31 bsc  mid-call-timeout 0  no missing-msc-text bsc does not seem to want to speak with trx-lms, I don't understand which config entry is wrong....  osmo_bsc_main.c:284 bootstrapping RSL for BTS/TRX (0/0) on ARFCN 871 using MCC-MNC 001-01 LAC=1 CID=0 BSIC=63 <0007> a_reset.c:106 A-RESET(msc-0)[0xdb2e98]{DISC}: (re)sending BSSMAP RESET message... <0007> osmo_bsc_sigtran.c:93 Sending RESET to MSC: RI=SSN_PC,PC=0.23.1,SSN=BSSAP <0007> osmo_bsc_bssap.c:58 RESET ACK from MSC: RI=SSN_PC,PC=0.23.1,SSN=BSSAP <0007> a_reset.c:74 A-RESET(msc-0)[0xdb2e98]{DISC}: SIGTRAN connection succeded. <0011> bts_ipaccess_nanobts.c:315 timeslot(0-0-0-CCCH_SDCCH4)[0xddfcd8]{UNUSED}: Event TS_EV_OML_READY not permitted <0011> bts_ipaccess_nanobts.c:315 timeslot(0-0-1-TCH_F)[0xde0038]{UNUSED}: Event TS_EV_OML_READY not permitted <0011> bts_ipaccess_nanobts.c:315 timeslot(0-0-2-TCH_F)[0xde0398]{UNUSED}: Event TS_EV_OML_READY not permitted <0011> bts_ipaccess_nanobts.c:315 timeslot(0-0-3-TCH_F)[0xde06f8]{UNUSED}: Event TS_EV_OML_READY not permitted <0011> bts_ipaccess_nanobts.c:315 timeslot(0-0-4-TCH_F)[0xde0a58]{UNUSED}: Event TS_EV_OML_READY not permitted <0011> bts_ipaccess_nanobts.c:315 timeslot(0-0-5-TCH_F)[0xde0db8]{UNUSED}: Event TS_EV_OML_READY not permitted <0011> bts_ipaccess_nanobts.c:315 timeslot(0-0-6-TCH_F)[0xde1118]{UNUSED}: Event TS_EV_OML_READY not permitted <0011> bts_ipaccess_nanobts.c:315 timeslot(0-0-7-TCH_F)[0xde1478]{UNUSED}: Event TS_EV_OML_READY not permitted <0015> input/ipaccess.c:248 Sign link vanished, dead socket <0015> input/ipaccess.c:74 Forcing socket shutdown with no signal link set <0015> bts_ipaccess_nanobts.c:416 (bts=0) Dropping OML link. <0015> bts_ipaccess_nanobts.c:397 (bts=0,trx=0) Dropping RSL link. <0015> input/ipa.c:262 accept()ed new link from 127.0.0.1 to port 3002 <0004> abis_nm.c:538 BTS0 feature 'EGPRS' reported via OML does not match statically set feature: 0 != 1. Please fix. <0004> abis_nm.c:538 BTS0 feature 'OML Alerts' reported via OML does not match statically set feature: 1 != 0. Please fix. So, has anyone config files for Limesdr mini -> trx-lms -> osmo-bts-trx_0.8.1.199 -> osmo-msc or can point me in the right direction.... Gullik