> I don't understand. This callback will be called with data you need to
write
> to the network. In case of MTP Level3 you will need to wrap that around
the
> msgb you got.
I means: is the interaction with mtp3 layer implemented (is sending sccp
data by mtp3 implemented by the library?)?
Also, what about the reception of data from mtp3 layer. is that implemented
in the sccp lib.
I am asking these questions because I see the code of mtp3 in the lib but no
significant call is present in the sccp part of the lib.
Thank you for your help.
Hi all,
This patch set adds to libosmocore an optimized Viterbi decodeer for
architecture specific (Intel SSE) and non-specific cases. The
implementation covers codes with constraint lengths of K=5 and K=7 and
rates 1/4 to 3/4, which make up the majority of GSM use cases. Speedup
from the current implementation is in the range of 5 to 20 depending on
the processor and code type. API is unchanged.
Tested on Haswell (i7-4770K) and Atom (D2550). Additional test codes
from osmo-bts are included. Further tests for AWGN bit-error-rate
and benchmarks can be found in the following repository.
https://github.com/ttsou/osmo-conv-test
Here are some examples.
Bit error test for GPRS CS2 with SNR of 5 dB and 100000 bursts.
$ ./conv_test -c 2 -e -r 5 -i 100000
=================================================
[+] Testing: GPRS CS2
[.] Specs: (N=2, K=5, non-recursive, flushed, not punctured)
[.] Input length : ret = 290 exp = 290 -> OK
[.] Output length : ret = 588 exp = 588 -> OK
[.] BER tests:
[..] Testing base:
[..] Input BER.......................... 0.042443
[..] Output BER......................... 0.000006
[..] Output FER......................... 0.001350 (135)
[..] Testing SIMD:
[..] Input BER.......................... 0.042460
[..] Output BER......................... 0.000005
[..] Output FER......................... 0.001240 (124)
Timed AFS benchmark with 8 threads and 100000 bursts per thread.
$ ./conv_test -b -c 10 -j 8 -i 100000
=================================================
[+] Testing: GSM TCH/AFS 6.7
[.] Specs: (N=4, K=5, recursive, flushed, punctured)
[.] Input length : ret = 140 exp = 140 -> OK
[.] Output length : ret = 448 exp = 448 -> OK
[.] Performance benchmark:
[..] Encoding / Decoding 800000 bursts on 8 thread(s):
[..] Testing base:
[..] Elapsed time....................... 4.320001 secs
[..] Rate............................... 25.925920 Mbps
[..] Testing SIMD:
[..] Elapsed time....................... 0.458272 secs
[..] Rate............................... 244.396341 Mbps
[..] Speedup............................ 9.426718
-TT
Dear all,
the valuable L1SAP abstraction has been sitting out of master for too
long time. It is a pity that this has taken so long. I've finally been
able to put some time into osmo-bts again and reviewed the following
patch series. It consists of mostly Andreas' work, interspersed with
smaller patches/fixups that I introduced after the respective original
patch from Andreas.
I have started a sysmobts between all of the major steps in this patch
series and did a short manual tests involving registration (LU) of two
MS, mobile-to-mobile call and vty-to-mobile SMS. So far I couldn't see
any problems. What has not been tested yet is the PCU interface as well
as encryption support. I plan to do this later this week.
I intend to merge the code after this current review cycle. Please take
your time to have a look and provide feedback (if any), so we can get
this over and work on new features again, rather than infrastrutural
changes.
I didn't yet rebase the osmo-bts-trx interface on top of the L1SAP, as I
don't have a hardware setup for it, and I will leave it to the owners of
such hardware to publish/push the respective code after L1SAP is merged.
Regards,
Harald
--
- Harald Welte <laforge(a)gnumonks.org> http://laforge.gnumonks.org/
============================================================================
"Privacy in residential applications is a desirable marketing option."
(ETSI EN 300 175-7 Ch. A6)
Dear Groupmembers
Please help me with this case. I have successfully sent rrlp request to the
mobile and the mobile automatically turns its gps on as a response to it.
But it doesn't provide me its location or request for any kind of
assistance data.
So please let me know what i am missing and what i have to do.
Thanks & Regards
Snehasish
