OpenBSC August 2009

openbsc@lists.osmocom.org

22 participants
48 discussions

How to tell MS no channel is available?
by Nordin 25 Aug '09

25 Aug '09

Hello guys, Suppose I have 8 MS registered on my nanoBTS and the ninth wants also to register. How can I tell the ninth MS "Sorry dude, there is no room for you, try another ARFCN"? I've checked the REJECT causes in gsm 04.08, but couldn't really find one which is informing the BTS is out of free channels. Now my mobile keeps trying to register to my nanoBTS, although I rejected him with a standard cause. Maybe someone can give me a hint where to look at? Thanks.

2 2

Cell Broadcast Support
by Galbayar D 25 Aug '09

25 Aug '09

Hi Is OpenBSC supports Cell Broadcast? If not is there any plan? or Is someone developing? Gala

3 2

How was HAR2009?
by Nordin 24 Aug '09

24 Aug '09

Well guys, Those who visited HAR2009, especially who visited the GSM related events, how was it? Share us you adventures :)

2 2

new patch for fragmenting HFC-E1
by Andreas.Eversberg 24 Aug '09

24 Aug '09

hi, here is the almost final patch for fragmenting HFC-E1 cards for multiple BTS connecting to one card. if it is stable, i will submit it after some tests. load module with: $ modprobe hfcmulti dmask=0x00000042 bmask=0x0000003c,0x00000780 debug=0x40000 the dmask must be given von all E1 cards that have to be fragmented. in this case we only fragment the first card. the bmask must be given for all fragments. because we have two bits set (slot 1 and slot 6), we need two values. each bmask value will define the the bchannels to use for the given dchannel. the card is fragmented from lower dchannel to higher dchannel given in the mask. (slot 1 for first fragment, slot 2 for second fragment) run misdn_info after loading to see the fragments. happy testing, andreas

2 1

some bug reports for subscr usage
by Andreas.Eversberg 23 Aug '09

23 Aug '09

hi, i found some leaking on the subscriber ressource usage. this patch is not final. maybe we find better solutions. 1. trans_alloc() may not allocate subscriber for transaction, because may be already done before, so i removed subscr_get() from transaction.c -> on outgoing calls we allocate subscriber ressource (by searching for it) and use it for transaction. -> in incomming calls we use the subscriber pointer from the lchan. 2. on an incomming call/sms, the lchan holds a subscriber ressource, so i added subscr_get() after successfully calling trans_alloc() 3. when _send_sms_buffer() is called, we already hold a subscriber ressource for the receiver, so the subsequently called function sms_from_text() must not allocate the receiver again. if this function fails, the allocated subcriber ressource must be released in _send_sms_buffer(). 4. on trans_free we don't need to remove pending paging processes, because it is done when paging expires. anyway if we want to keep it in trans_free(), we must remove paging_remove_request() from paging_T3113_expired(), because it will then be done when transaction is removed. also we need to add paging_remove_request() when sms is removed due to paging expiery. i also fixed linux call router for compiling with openbsc without any patch at all. by linking the source directory to the lcr source directory, the "configure" script automatically detects it and it will compile. (latest git) regards, andreas

1 0

Does anyone have IuH (RUA/HNBAP) captures?
by Harald Welte 23 Aug '09

23 Aug '09

Hi! I've alerady sent this to wireshark-dev, but maybe somebody on this list can also help... I'm right now working for a dissector for the 3GPP IuH (Home-NodeB) protocol. However, I believe the pcap files that I currently have for the protocol are actually invalid. Is there anyone on this list who would be able to provide me with RUA and/or HNBAP protocol traces (preferrably inside SCTP)? Thanks a lot. -- - Harald Welte <laforge(a)gnumonks.org> http://laforge.gnumonks.org/ ============================================================================ "Privacy in residential applications is a desirable marketing option." (ETSI EN 300 175-7 Ch. A6)

1 0

BS-11 link does not come up
by Sergey V. Efimoff 21 Aug '09

21 Aug '09

Hello All, When trying to run bsc_hack I get the following messages: bootstrapping OML for BTS 0 <0020> abis_nm.c:1644 Set BTS Attr (bts=0) <0020> abis_nm.c:1661 Set TRX Attr (bts=0,trx=0) <0020> abis_nm.c:1754 Set Chan Attr (bts=0,trx=0,ts=0) <0020> abis_nm.c:1754 Set Chan Attr (bts=0,trx=0,ts=1) <0020> abis_nm.c:1624 CONNECT TERR TRAF Um=(bts=0,trx=0,ts=1) E1=(0,2,1) <0020> abis_nm.c:1754 Set Chan Attr (bts=0,trx=0,ts=2) <0020> abis_nm.c:1624 CONNECT TERR TRAF Um=(bts=0,trx=0,ts=2) E1=(0,2,2) <0020> abis_nm.c:1754 Set Chan Attr (bts=0,trx=0,ts=3) <0020> abis_nm.c:1624 CONNECT TERR TRAF Um=(bts=0,trx=0,ts=3) E1=(0,2,3) <0020> abis_nm.c:1754 Set Chan Attr (bts=0,trx=0,ts=4) <0020> abis_nm.c:1624 CONNECT TERR TRAF Um=(bts=0,trx=0,ts=4) E1=(0,3,0) <0020> abis_nm.c:1754 Set Chan Attr (bts=0,trx=0,ts=5) <0020> abis_nm.c:1624 CONNECT TERR TRAF Um=(bts=0,trx=0,ts=5) E1=(0,3,1) <0020> abis_nm.c:1754 Set Chan Attr (bts=0,trx=0,ts=6) <0020> abis_nm.c:1624 CONNECT TERR TRAF Um=(bts=0,trx=0,ts=6) E1=(0,3,2) <0020> abis_nm.c:1754 Set Chan Attr (bts=0,trx=0,ts=7) <0020> abis_nm.c:1624 CONNECT TERR TRAF Um=(bts=0,trx=0,ts=7) E1=(0,3,3) bootstrapping RSL for BTS/TRX (0/0) using MCC=1 MNC=1 BSIC=1 TSC=7 <0020> abis_nm.c:805 OC=SIEMENSHW(a5) INST=(03,00,00) STATE CHG: <0020> abis_nm.c:805 OC=SIEMENSHW(a5) INST=(03,00,00) Failure Event Report Severity=indeterminate failure <0020> abis_nm.c:805 OC=SIEMENSHW(a5) INST=(03,00,00) STATE CHG: Debug with -dDMI:DRSL:DNM shows strange lines: ... <1000> input/misdn.c:132 DL_INFORMATION_IND: use channel(0) sapi(63) tei(127) for now mISDN message for unknown sign_link ... <1000> input/misdn.c:132 DL_INFORMATION_IND: use channel(2) sapi(62) tei(1) for now mISDN message for unknown sign_link ... Why TEI=1 or TEI=127 while it should be 25? Also, dmesg produces: ... mISDN_send: error -12 ... I've reviewed mailing list for similiar problems description and found that several people have already seen these problems, but didn't find the solution. I thought that these problems may be connected with internal BS11 oscillator calibration, so I've performed calibration as described in wiki (though I used Nateks SDH mux with Stratum oscillator as E1 clock source instead of HFC-S ISDN card, which I don't have). Calibration was successful, but it didn't help. Here is query output while running bsc_hack: ... LMT LOGON: ACK PHASE: 3 Normal MBCCU0: Load MBCCU1: No Load Abis-link: Up BS11 ATTRIBUTES: BS-11 ESN PCB Serial Number: 001132 BS-11 ESN Hardware Code Number: 135-2044/03.03 BS-11 ESN Firmware Code Number: 135-2044/03.03 E1 Channel: Port=255 Timeslot=161 Subslot=39 PLL Set Value=1024, Work Value=1023 SITE MANAGER ATTRIBUTES: E1 Channel: Port=0 Timeslot=1 (Full Slot) TEI: 25 BS11 Line Interface ATTRIBUTES: PLL Mode: Standalone BS11 CCLK ATTRIBUTES: CCLK Accuracy: Medium (0) BS11 Power Amplifier 0 ATTRIBUTES: TRX Power: 30mW (GSM) LMT LOGOFF: ACK ... It seems that everything should be ok, but... there is no success. Best regards, Sergey.

2 4

RFC: Change gsm_subscriber tmsi from char[17] to u_int32_t
by Holger Freyther 21 Aug '09

21 Aug '09

Hey guys, for some historic reason our tmsi is an character array but all places dealing with it treat it as a 4 octet, and according to the spec it is a four octet. I have changed the definition and the code using the tmsi. It can be found in my onwaves.com branch. Does it make sense to switch? z.

3 2

AW: Problems with HFC-E1 card (Unknown HFC multiport controller)
by Andreas.Eversberg 21 Aug '09

21 Aug '09

both subdevices: b553 and b523 are already part of the driver. { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, PCI_SUBDEVICE_ID_CCD_IOB1E1, 0, 0, H(24)}, /* IOB1E1 */ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD, PCI_SUBDEVICE_ID_CCD_JHSE1, 0, 0, H(25)}, /* Junghanns E1 */ please check definitions. PCI_SUBDEVICE_ID_CCD_IOB1E1 should be b523 and PCI_SUBDEVICE_ID_CCD_JHSE1 should be b553. (do a grep onto your repository (grep b523 <path>/* -r) -----Ursprüngliche Nachricht----- Von: openbsc-bounces(a)lists.gnumonks.org [mailto:openbsc-bounces@lists.gnumonks.org] Im Auftrag von Harald Welte Gesendet: Mittwoch, 19. August 2009 18:08 An: dexter Cc: openbsc(a)lists.gnumonks.org Betreff: Re: Problems with HFC-E1 card (Unknown HFC multiport controller) On Mon, Aug 17, 2009 at 08:24:50PM +0200, dexter wrote: > Here is an output from a linux box that works with the other card: > Unknown HFC multiport controller (vendor:1397 device:30b1 > subvendor:ffffffff subdevice:ffffffff) Please contact the driver > maintainer for support. Hi, I think you should report this to the misdn development list. as a quick workaround, I suggesty you add the pci vendor / device ID to the hfcmulti.c driver (hfcmulti_probe() would be the case). What particular HFC-E1 card is this? At least according to my kernel, PCI_VENDOR_ID_CCD is 0x1397 PCI_DEVICE_ID_CCD_HFCE1 is 0x30b1 so I don't know why you get that message... -- - Harald Welte <laforge(a)gnumonks.org> http://laforge.gnumonks.org/ ============================================================================ "Privacy in residential applications is a desirable marketing option." (ETSI EN 300 175-7 Ch. A6)

1 0

Problems with HFC-E1 card (Unknown HFC multiport controller)
by dexter 19 Aug '09

19 Aug '09

Here is an output from a linux box that works with the other card: openbsc output: tatooine:/home/laflocal/openbsc/openbsc/src# ./bsc_hack -f 123 DB: Database initialized. DB: Database prepared. 0 devices found error getting info for device 0: No such device Error during E1 config of BTS 0 lspci output: tatooine:~# lspci 00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4) 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22) 00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10) 00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) 00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) 00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30) 00:09.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-E1] (rev 01) 00:0a.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller 00:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) 00:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) 00:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63) 00:0e.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 07) 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400/G450 (rev 03) Dmesg output: tatooine:~# dmesg Linux version 2.6.30.4 (root@tatooine) (gcc version 4.3.2 (Debian 4.3.2-1) ) #1 SMP Sat Aug 8 01:44:27 CEST 2009 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD NSC Geode by NSC Cyrix CyrixInstead Centaur CentaurHauls Transmeta GenuineTMx86 Transmeta TransmetaCPU UMC UMC UMC UMC BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000002fff0000 (usable) BIOS-e820: 000000002fff0000 - 000000002fff8000 (ACPI data) BIOS-e820: 000000002fff8000 - 0000000030000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) DMI 2.3 present. AMI BIOS detected: BIOS may corrupt low RAM, working around it. e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) last_pfn = 0x2fff0 max_arch_pfn = 0x100000 MTRR default type: uncachable MTRR fixed ranges enabled: 00000-9FFFF write-back A0000-BFFFF uncachable C0000-C7FFF write-protect C8000-EFFFF uncachable F0000-FFFFF write-protect MTRR variable ranges enabled: 0 base 000000000 mask FE0000000 write-back 1 base 020000000 mask FF0000000 write-back 2 disabled 3 disabled 4 disabled 5 disabled 6 base 0E0000000 mask FFC000000 write-combining 7 disabled init_memory_mapping: 0000000000000000-000000002fff0000 0000000000 - 0000400000 page 4k 0000400000 - 002fc00000 page 2M 002fc00000 - 002fff0000 page 4k kernel direct mapping tables up to 2fff0000 @ 10000-15000 ACPI: RSDP 000fc5b0 00014 (v00 AMI ) ACPI: RSDT 2fff0000 0002C (v01 AMIINT 00000010 MSFT 00000099) ACPI: FACP 2fff0030 00074 (v01 AMIINT 00000010 MSFT 00000099) ACPI: DSDT 2fff0110 02F9D (v01 VIA APOLLO-P 00001000 MSFT 0100000B) ACPI: FACS 2fff8000 00040 ACPI: APIC 2fff00b0 0005C (v01 AMIINT 00000009 MSFT 00000099) ACPI: Local APIC address 0xfee00000 767MB LOWMEM available. mapped low ram: 0 - 2fff0000 low ram: 0 - 2fff0000 node 0 low ram: 00000000 - 2fff0000 node 0 bootmap 00011000 - 00017000 (8 early reservations) ==> bootmem [0000000000 - 002fff0000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000100000 - 000064b2a4] TEXT DATA BSS ==> [0000100000 - 000064b2a4] #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] #5 [000064c000 - 000064e0d0] BRK ==> [000064c000 - 000064e0d0] #6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000] #7 [0000011000 - 0000017000] BOOTMAP ==> [0000011000 - 0000017000] found SMP MP-table at [c00fb170] fb170 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 Normal 0x00001000 -> 0x0002fff0 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000010 -> 0x0000009f 0: 0x00000100 -> 0x0002fff0 On node 0 totalpages: 196479 free_area_init_node: node 0, pgdat c0581d60, node_mem_map c1000200 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 3951 pages, LIFO batch:0 Normal zone: 1504 pages used for memmap Normal zone: 190992 pages, LIFO batch:31 Using APIC driver default ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ11 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information SMP: Allowing 2 CPUs, 0 hotplug CPUs nr_irqs_gsi: 24 PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000 PM: Registered nosave memory: 00000000000dc000 - 00000000000e0000 PM: Registered nosave memory: 00000000000e0000 - 00000000000f0000 PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 Allocating PCI resources starting at 40000000 (gap: 30000000:cec00000) NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1 PERCPU: Embedded 11 pages at c1604000, static data 22748 bytes Built 1 zonelists in Zone order, mobility grouping on. Total pages: 194943 Kernel command line: root=/dev/hda6 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 NR_IRQS:320 PID hash table entries: 4096 (order: 12, 16384 bytes) Fast TSC calibration using PIT Detected 730.766 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 773228k/786368k available (3239k kernel code, 12500k reserved, 1450k data, 316k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfff9d000 - 0xfffff000 ( 392 kB) vmalloc : 0xf07f0000 - 0xfff9b000 ( 247 MB) lowmem : 0xc0000000 - 0xefff0000 ( 767 MB) .init : 0xc059c000 - 0xc05eb000 ( 316 kB) .data : 0xc0429e99 - 0xc05949a4 (1450 kB) .text : 0xc0100000 - 0xc0429e99 (3239 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Calibrating delay loop (skipped), value calculated using timer frequency.. 1461.53 BogoMIPS (lpj=2923064) Mount-cache hash table entries: 512 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. ACPI: Core revision 20090320 ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel Pentium III (Coppermine) stepping 03 Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 1461.72 BogoMIPS (lpj=2923453) CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Pentium III (Coppermine) stepping 03 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs Total of 2 processors activated (2923.25 BogoMIPS). net_namespace: 980 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1 PCI: Using configuration type 1 for base access mtrr: your CPUs had inconsistent variable MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. bio: create slab <bio-0> at 0 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: Power Resource [URP1] (off) ACPI: Power Resource [URP2] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:00.0: reg 10 32bit mmio: [0xe0000000-0xe3ffffff] pci 0000:00:01.0: supports D1 pci 0000:00:07.1: reg 20 io port: [0xffa0-0xffaf] pci 0000:00:07.2: reg 20 io port: [0xc400-0xc41f] pci 0000:00:07.3: reg 20 io port: [0xc800-0xc81f] pci 0000:00:07.4: quirk: region 0800-08ff claimed by vt82c586 ACPI pci 0000:00:07.4: quirk: region 0c00-0c7f claimed by vt82c686 HW-mon pci 0000:00:07.4: quirk: region 0400-040f claimed by vt82c686 SMB pci 0000:00:09.0: reg 10 io port: [0xcc00-0xcc07] pci 0000:00:09.0: reg 14 32bit mmio: [0xdfffd000-0xdfffdfff] pci 0000:00:09.0: supports D1 D2 pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot pci 0000:00:09.0: PME# disabled pci 0000:00:0a.0: reg 10 32bit mmio: [0xdffc0000-0xdffdffff] pci 0000:00:0a.0: reg 14 32bit mmio: [0xdffa0000-0xdffbffff] pci 0000:00:0a.0: reg 18 io port: [0xd000-0xd03f] pci 0000:00:0a.0: reg 30 32bit mmio: [0xdff80000-0xdff9ffff] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold pci 0000:00:0a.0: PME# disabled pci 0000:00:0b.0: reg 20 io port: [0xd400-0xd41f] pci 0000:00:0b.0: supports D1 D2 pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot pci 0000:00:0b.0: PME# disabled pci 0000:00:0b.1: reg 20 io port: [0xd800-0xd81f] pci 0000:00:0b.1: supports D1 D2 pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot pci 0000:00:0b.1: PME# disabled pci 0000:00:0b.2: reg 10 32bit mmio: [0xdfffff00-0xdfffffff] pci 0000:00:0b.2: supports D1 D2 pci 0000:00:0b.2: PME# supported from D0 D1 D2 D3hot pci 0000:00:0b.2: PME# disabled pci 0000:00:0e.0: reg 10 io port: [0xdc00-0xdc3f] pci 0000:00:0e.0: supports D2 pci 0000:01:00.0: reg 10 32bit mmio: [0xdc000000-0xddffffff] pci 0000:01:00.0: reg 14 32bit mmio: [0xdfefc000-0xdfefffff] pci 0000:01:00.0: reg 18 32bit mmio: [0xdf000000-0xdf7fffff] pci 0000:01:00.0: reg 30 32bit mmio: [0xdfee0000-0xdfeeffff] pci 0000:00:01.0: bridge io port: [0x9000-0x9fff] pci 0000:00:01.0: bridge 32bit mmio: [0xdee00000-0xdfefffff] pci 0000:00:01.0: bridge 32bit mmio pref: [0xdac00000-0xdecfffff] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 11 devices ACPI: ACPI bus type pnp unregistered pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: 0x9000-0x9fff pci 0000:00:01.0: MEM window: 0xdee00000-0xdfefffff pci 0000:00:01.0: PREFETCH window: 0x000000dac00000-0x000000decfffff pci 0000:00:01.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] pci_bus 0000:01: resource 0 io: [0x9000-0x9fff] pci_bus 0000:01: resource 1 mem: [0xdee00000-0xdfefffff] pci_bus 0000:01: resource 2 pref mem [0xdac00000-0xdecfffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 Machine check exception polling timer started. Installing knfsd (copyright (C) 1996 okir(a)monad.swb.de). msgmni has been set to 1510 alg: No test for stdrng (krng) io scheduler noop registered io scheduler cfq registered (default) pci 0000:00:01.0: disabling DAC on VIA PCI bridge pci 0000:00:07.0: Enabling VIA external APIC routing pci 0000:01:00.0: Boot video device Non-volatile memory driver v1.3 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 brd: module loaded loop: module loaded Uniform Multi-Platform E-IDE driver via82cxxx 0000:00:07.1: VIA vt82c686a (rev 22) IDE UDMA66 via82cxxx 0000:00:07.1: IDE controller (0x1106:0x0571 rev 0x10) via82cxxx 0000:00:07.1: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7 ide1: BM-DMA at 0xffa8-0xffaf Probing IDE interface ide0... hda: SAMSUNG SP1213N, ATA DISK drive hdb: Maxtor 6Y160L0, ATA DISK drive hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4 hda: UDMA/66 mode selected hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4 hdb: UDMA/66 mode selected Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports ide-gd driver 1.18 hda: max request size: 512KiB hda: 234493056 sectors (120060 MB) w/8192KiB Cache, CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 hda15 hda16 > hdb: max request size: 512KiB hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63 hdb: cache flushes supported hdb: hdb1 ide-cd driver 5.00 uhci_hcd: USB Universal Host Controller Interface driver ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:07.2: VIA VLink IRQ fixup, from 5 to 10 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 10, io base 0x0000c400 usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: UHCI Host Controller usb usb1: Manufacturer: Linux 2.6.30.4 uhci_hcd usb usb1: SerialNumber: 0000:00:07.2 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:07.3: PCI INT D -> Link[LNKD] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:07.3: VIA VLink IRQ fixup, from 5 to 10 uhci_hcd 0000:00:07.3: UHCI Host Controller uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:07.3: irq 10, io base 0x0000c800 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.30.4 uhci_hcd usb usb2: SerialNumber: 0000:00:07.3 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:0b.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:0b.0: UHCI Host Controller uhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:0b.0: irq 19, io base 0x0000d400 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.30.4 uhci_hcd usb usb3: SerialNumber: 0000:00:0b.0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:0b.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:0b.1: UHCI Host Controller uhci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:0b.1: irq 16, io base 0x0000d800 usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.30.4 uhci_hcd usb usb4: SerialNumber: 0000:00:0b.1 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usbcore: registered new interface driver libusual usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice rtc_cmos 00:02: RTC can wake from S4 rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one year, y3k, 114 bytes nvram Driver for 1-wire Dallas network protocol. cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. Using IPI No-Shortcut mode rtc_cmos 00:02: setting system clock to 2009-08-17 18:17:55 UTC (1250533075) EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. usb 1-2: new full speed USB device using uhci_hcd and address 2 usb 1-2: New USB device found, idVendor=067b, idProduct=2303 usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-2: Product: USB-Serial Controller D usb 1-2: Manufacturer: Prolific Technology Inc. usb 1-2: configuration #1 chosen from 1 choice usb 4-2: new full speed USB device using uhci_hcd and address 2 usb 4-2: New USB device found, idVendor=05e3, idProduct=0605 usb 4-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0 usb 4-2: Product: USB2.0 Hub usb 4-2: configuration #1 chosen from 1 choice hub 4-2:1.0: USB hub found hub 4-2:1.0: 4 ports detected kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with writeback data mode. VFS: Mounted root (ext3 filesystem) readonly on device 3:6. Freeing unused kernel memory: 316k freed Write protecting the kernel text: 3240k Write protecting the kernel read-only data: 1212k Linux agpgart interface v0.103 parport_pc: VIA 686A/8231 detected parport_pc: probing current configuration parport_pc: Current parallel port base: 0x378 parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP] agpgart: Detected VIA Apollo Pro 133 chipset agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xe0000000 parport_pc: VIA parallel port: io=0x378, irq=7 Modular ISDN core version 1.1.20 input: Power Button as /class/input/input0 ACPI: Power Button [PWRF] input: Power Button as /class/input/input1 ACPI: Power Button [PWRB] input: Sleep Button as /class/input/input2 ACPI: Sleep Button [SLPB] NET: Registered protocol family 34 Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI Copyright (c) 1999-2006 Intel Corporation. e1000 0000:00:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 e1000 0000:00:0a.0: PCI: Disallowing DAC for device processor ACPI_CPU:00: registered as cooling_device0 processor ACPI_CPU:01: registered as cooling_device1 thermal LNXTHERM:01: registered as thermal_zone0 ACPI: Thermal Zone [THRM] (33 C) mISDN: HFC-multi driver 2.03 e1000: 0000:00:0a.0: e1000_probe: (PCI:33MHz:32-bit) 00:0e:0c:59:51:58 input: PC Speaker as /class/input/input3 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after USB Serial support registered for pl2303 pl2303 1-2:1.0: pl2303 converter detected usb 1-2: pl2303 converter now attached to ttyUSB0 usbcore: registered new interface driver pl2303 pl2303: Prolific PL2303 USB to serial adaptor driver e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection Unknown HFC multiport controller (vendor:1397 device:30b1 subvendor:ffffffff subdevice:ffffffff) Please contact the driver maintainer for support. ehci_hcd 0000:00:0b.2: PCI INT C -> GSI 17 (level, low) -> IRQ 17 ehci_hcd 0000:00:0b.2: EHCI Host Controller ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:0b.2: irq 17, io mem 0xdfffff00 ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 1.00 usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: EHCI Host Controller usb usb5: Manufacturer: Linux 2.6.30.4 ehci_hcd usb usb5: SerialNumber: 0000:00:0b.2 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 4 ports detected usb 4-2: USB disconnect, address 2 usb 5-4: new high speed USB device using ehci_hcd and address 2 usb 5-4: New USB device found, idVendor=05e3, idProduct=0605 usb 5-4: New USB device strings: Mfr=0, Product=1, SerialNumber=0 usb 5-4: Product: USB2.0 Hub usb 5-4: configuration #1 chosen from 1 choice hub 5-4:1.0: USB hub found hub 5-4:1.0: 4 ports detected Adding 2008084k swap on /dev/hda5. Priority:-1 extents:1 across:2008084k EXT3 FS on hda6, internal journal SCSI subsystem initialized Driver 'sr' needs updating - please use bus_type methods Linux Tulip driver version 1.1.15-NAPI (Feb 27, 2007) device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel(a)redhat.com kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: mounted filesystem with writeback data mode. NET: Registered protocol family 15 alg: No test for cipher_null (cipher_null-generic) alg: No test for ecb(cipher_null) (ecb-cipher_null) alg: No test for digest_null (digest_null-generic) alg: No test for compress_null (compress_null-generic) e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX NET: Registered protocol family 10 lo: Disabled Privacy Extensions tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk(a)qualcomm.com> tun0: Disabled Privacy Extensions lp0: using parport0 (interrupt-driven). ppdev: user-space parallel port driver svc: failed to register lockdv1 RPC service (errno 97). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period [drm] Initialized drm 1.1.0 20060810 pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [drm] Initialized mga 3.2.1 20051102 for 0000:01:00.0 on minor 0 agpgart-via 0000:00:00.0: AGP 2.0 bridge agpgart-via 0000:00:00.0: putting AGP V2 device into 1x mode pci 0000:01:00.0: putting AGP V2 device into 1x mode [drm] Initialized card for AGP DMA.

2 1

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

OpenBSC August 2009