21 Feb
2013
21 Feb
'13
9:07 p.m.
Hello List
I'm trying to make my openbsc installation work in half rate mode but
I'm facing some errors.
I'm wondering if someone could provide me with more info or help me to
configure openbsc.
I have changed in openbsc.cfg the timeslots 2 to 7 from
phys_chan_config TCH/F into phys_chan_config TCH/H also I have tested
changing neci bit and change audio codecs but no luck.
Am I missed something? Is there any way to run osmo-nitb with gsmtap?
openbsc.cfg is attached
Thanks in advance.
1:15 p.m.
On 02/22/2013 01:18 AM, Sylvain Munaut wrote:
Thanks for the immediate response.
Is your answer based on hands-on experience, feedback from other
developers/users or something else?
In the nanoGSM® EDGE 900 datasheet is not mentioned the TCH/H support,
but the nanoGSM® EDGE 1800 model seems to support it.
Do you believe that the 1800 model could work?
Also I noticed in the OpenBSC wiki that TCH/H is not implemented in
osmo-nitb but only in osmo-bsc, is this information correct?
Thanks for your time.
./Vervelak
I'm trying
to make my openbsc installation work in half rate mode but
I don't think
nanoBTS support HR codec at all ...
Cheers,
Sylvain 
2:55 p.m.
./Vervelak wrote:
Also I noticed in the OpenBSC wiki that TCH/H is not
implemented in
osmo-nitb but only in osmo-bsc, is this information correct?
there are several
reasons why TCH/H is not currently working with
osmo-nitb. i plan to make it work soon, but it still requires BTS to
support it.
4:59 p.m.
Is your answer based on hands-on experience, feedback
from other
developers/users or something else?
hands-on experience.
In the nanoGSM® EDGE 900 datasheet is not mentioned
the TCH/H support, but
the nanoGSM® EDGE 1800 model seems to support it.
TCH/H != HR
The EDGE models do support AMR-HR. But that's different from HR. And
not supported by osmo-nitb currently.
Cheers,
Sylvain
27 Feb
27 Feb
8:31 p.m.
On 2/22/13 5:59 PM, Sylvain Munaut wrote:
So, the nanoBTS support AMR speech codec but don't
support HR speech codec
and in osmo-bsc TCH/H is supported unlike osmo-nitb?
and if i write code in osmo-nitb that support TCH/H i will have 14
simulate calls in my setup?
are there any guidelines for new openBSC developers or can someone provide me with some
highlights about porting TCH/H from osmo-bsc to osmo-nitb?
Thanks again for your time.
Is your answer
based on hands-on experience, feedback from other
developers/users or something else?
hands-on experience.
In the nanoGSM® EDGE 900 datasheet is not
mentioned the TCH/H support, but
the nanoGSM® EDGE 1800 model seems to support it.
TCH/H != HR
The EDGE models do support AMR-HR. But that's different from HR. And
not supported by osmo-nitb currently.
Cheers,
Sylvain
28 Feb
28 Feb
8:12 a.m.
N.v wrote:
are there any guidelines for new openBSC developers or
can someone
provide me with some
highlights about porting TCH/H from osmo-bsc to osmo-nitb?
hi,
there are several things that need to be done to support TCH/H as well
as AMR codec at osmo-nitb. as i said before, i am working on it.
regards,
andreas
4096
days inactive
4103
days old
6 comments
4 participants
participants (4)
-
./Vervelak -
jolly -
N.v
-
Sylvain Munaut