baseband-devel

baseband-devel@lists.osmocom.org

3 participants
2004 discussions

Re: Sniff Code..shown @chao conf.. CCC
by Aaron Zauner 24 Jan '11

24 Jan '11

Oh, i also found this: http://permalink.gmane.org/gmane.comp.gnu.radio.general/31145 -> http://en.wikipedia.org/wiki/Manoj_Kumar lol. so long, azet

6 7

[PATCH] Support GNU make when it is not called "make"
by Pierre Pronchery 24 Jan '11

24 Jan '11

Hi baseband developers, just a small patch to help where GNU make is not directly called "make". HTH, -- khorben

1 0

Creatng a list of known issues somewhere
by Holger Hans Peter Freyther 24 Jan '11

24 Jan '11

Hi all, it appears that we all know of some issues but we are not writing them down. Would it make sense to start using the bugtracker for that? Or just a dedicated wiki site?

2 2

problems getting Pirelli DP-L10 to work
by Leif Jakob 24 Jan '11

24 Jan '11

Hi, maybe I'm missing something, but when I read that the Pirelli DP-L10 would be supported I tried to get it running: I didn't patch my usb-module, but used: modprobe -v cp210x echo "0489 e003" > /sys/bus/usb-serial/drivers/cp210x/new_id from the steve-m/testing-branch I compiled the firmware and loaded it with ./host/osmocon/osmocon -p /dev/ttyUSB0 -m romload target/firmware/board/pirelli_dpl10/hello_world.highram.bin onto the phone... that worked but I was never able to see any messages after the upload: Received block ack from phone Sending checksum: 0xaa Checksum on phone side matches, let's branch to your code Branching to 0x00820000 Received branch ack, your code is running now! ... there it stayed forever ... I'm pretty sure that the code runs, because I commented in init.c the keyboard lighting code and it didn't light up after upload. I've tried other bins but to no success. Any hint or am it too early playing with that hardware? Greetings Leif

2 1

Regarding IMSI detach DoS
by Bogdan Alecu 24 Jan '11

24 Jan '11

Hello, In order for this attack to work it has to be on a GSM network because on 3G there is a higher security mechanism. A way to protect against this, for the opperator, could be to implement 3G over 900Mhz so this way even if the targeted phones are on 2G they will still be protected. Am I right? Regards, Bogdan

2 1

serial cable
by Tommy R. 23 Jan '11

23 Jan '11

Hey, I ordered the serial cable coming from dealextreme and it has not arrived yet. I noticed today that the link was taken off the wiki due to it not being at TTL levels. I was wondering if I bought a Nokia serial cable (the ones that have the prolific chips in them) which runs at 3.3v out of the box, could I just connect the tx and rx pins to the cable I had bought and it would possibly work or would that be a bad idea and I should cut my losses and kill the order. -- -Tom

2 1

Sniff Code..shown @chao conf.. CCC
by Marten Christophe 23 Jan '11

23 Jan '11

Hello All, Pls help me, any one who can Kindly give me code or even binary file for sniff code which Sylvain demonstrated in chao meeting, it will solve my purpose, i can See, in video he made the same interface to tune to a ARFCN, TS , and hopping sequence as i requested a long time back to mailling list It will be great help for poor students. my project don't required any a5 creaking so it wont be used as unlawful means. so far i have arranged 12 USRP1 to run openBTS. I just wanted to do the same, which Sylvain have done in video @ chao presentation, except cracking the encryption as i will configure openBTS as a5/0 coz it’s education transmission not necessary to encrypt kindly do me a favour in shake of charity. Pls reply to my query pls help me in the shake of poor students. I promise will keep that code secret and will not disclose to any one else. or pls advise me how i can modify existing code up to that level. Kindly reply on my request , can you pls provide me Sniff software? it will help me allot, my NGO can deploy a pilot project at least Kind Regards,

4 3

Non Standard Baud Rates?
by MATTHEW EVANS 22 Jan '11

22 Jan '11

Hi, I'm trying to get the burst_ind branch working at the higher speed baud rates. I have a USB to Serial FTDI Cable (FT232R) plus the T191. This setup works fine with the main trunk of osmocombb. When I fire up osmocon, layer1 appears to download to the phone and runs successfully. Osmocon then logs 'Received DOWNLOAD ACK from phone, your code is running now!'. The phone has layer1.bin displayed as usual. However it goes no further and just hangs. Could anyone please give any advice on what to try next? Thanks, Matt.

2 1

Why my phone can't attach the network?
by xuchenyu 22 Jan '11

22 Jan '11

Thanks to Tomas and ton, I can run osmocombb on the phone. But the phone can't attach the network, can't make a call, can't recognise the SIM card. I found that this was no BCCH received in wireshark. And when I type some command via telnet localhost, it always output "Command incomplete" Anybody can give me some solution? Thanks! -- View this message in context: http://baseband-devel.722152.n3.nabble.com/Why-my-phone-can-t-attach-the-ne… Sent from the baseband-devel mailing list archive at Nabble.com.

2 1

Re:radio is not started
by Bogdan Alecu 21 Jan '11

21 Jan '11

I guess you have the default configuration: "No Mobile Station defined, creating: MS '1'" After you start "mobile" application, select "enable" and then "write". This will write your configuration to /etc/osmocom/osmocom.cfg After that edit this file and set from no sim to sim reader. Restart the mobile application and it should work.

2 3

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

baseband-devel