Hi Richard, I didn't specify details because everything working properly, beside its just stuck while running mobile application probably during cell sync. Its not charger case, its something different.

Beside this if we are talking about charger battery is charging anyway, it doesn't matter osmocom or no osmocom loaded, its USB. But the problem is usb power less (its limited to 100mA) then phone power consumption. do lsusb -v

Bus 001 Device 020: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10

Device Descriptor:

bLength 18

bDescriptorType 1

bcdUSB 1.10

bDeviceClass 0 (Defined at Interface level)

bDeviceSubClass 0

bDeviceProtocol 0

bMaxPacketSize0 64

idVendor 0x0489 Foxconn / Hon Hai

idProduct 0xe003 Pirelli DP-L10

bcdDevice 1.00

iManufacturer 1 Silicon Labs

iProduct 2 DP-L10

iSerial 3 0001

bNumConfigurations 1

Configuration Descriptor:

bLength 9

bDescriptorType 2

wTotalLength 32

bNumInterfaces 1

bConfigurationValue 1

iConfiguration 0

bmAttributes 0x80

(Bus Powered)

MaxPower 100mA

MaxPower is 100mA. this is an issue.

----- Original Message -----

From: "Richard Menedetter" ricsi@gmx.at To: "Yury TSAREGORODTSEV" yury@bridgecommunication.co.uk Cc: baseband-devel@lists.osmocom.org Sent: Sunday, August 24, 2014 2:13:30 PM Subject: Aw: pirelli dp-l10 stuck

Hi Yuri You need to be waaaaaaay more specific of what you have done, and what you have seen. I have not noticed any problems, except the fact that the phone is not charged when Omocom programs are running. This means that when the battery is dead, you will loose power. The phone recognizes that it is charged (default FW) and boots into charging mode. CU, Ricsi Gesendet: Sonntag, 24. August 2014 um 11:39 Uhr Von: "TSAREGORODTSEV, Yury" yury@bridgecommunication.co.uk An: baseband-devel@lists.osmocom.org Betreff: pirelli dp-l10 stuck Hi, everybody has same trouble that pirelli stuck after some usage ?

Hi Steve, tried master and jolly/handover anyway my gcc: 4.7.2 (debian wheezy)

Yury

----- Original Message ----- From: "Steve Markgraf" steve@steve-m.de To: "Yury TSAREGORODTSEV" yury@bridgecommunication.co.uk, "Richard Menedetter" ricsi@gmx.at Cc: baseband-devel@lists.osmocom.org Sent: Sunday, August 24, 2014 2:59:49 PM Subject: Re: Aw: pirelli dp-l10 stuck

Hi,

On 24.08.2014 14:33, TSAREGORODTSEV, Yury wrote:

I didn't specify details because everything working properly, beside its just stuck while running mobile application probably during cell sync. Its not charger case, its something different.

Which branch are you using?

Make sure you have the following commit in your branch: http://cgit.osmocom.org/osmocom-bb/commit/?id=a903b3c1ee27047c79728b18ff6340...

Regards, Steve

Damn, yeah its not charging at all :) even when connected to hub with external power :)

Hi Richard, I didn't specify details because everything working properly, beside its just stuck while running mobile application probably during cell sync. Its not charger case, its something different.

Beside this if we are talking about charger battery is charging anyway, it doesn't matter osmocom or no osmocom loaded, its USB. But the problem is usb power less (its limited to 100mA) then phone power consumption. do lsusb -v

Bus 001 Device 020: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10

Device Descriptor:

bLength 18

bDescriptorType 1

bcdUSB 1.10

bDeviceClass 0 (Defined at Interface level)

bDeviceSubClass 0

bDeviceProtocol 0

bMaxPacketSize0 64

idVendor 0x0489 Foxconn / Hon Hai

idProduct 0xe003 Pirelli DP-L10

bcdDevice 1.00

iManufacturer 1 Silicon Labs

iProduct 2 DP-L10

iSerial 3 0001

bNumConfigurations 1

Configuration Descriptor:

bLength 9

bDescriptorType 2

wTotalLength 32

bNumInterfaces 1

bConfigurationValue 1

iConfiguration 0

bmAttributes 0x80

(Bus Powered)

MaxPower 100mA

MaxPower is 100mA. this is an issue.

----- Original Message -----

From: "Richard Menedetter" ricsi@gmx.at To: "Yury TSAREGORODTSEV" yury@bridgecommunication.co.uk Cc: baseband-devel@lists.osmocom.org Sent: Sunday, August 24, 2014 2:13:30 PM Subject: Aw: pirelli dp-l10 stuck

Hi Yuri You need to be waaaaaaay more specific of what you have done, and what you have seen. I have not noticed any problems, except the fact that the phone is not charged when Omocom programs are running. This means that when the battery is dead, you will loose power. The phone recognizes that it is charged (default FW) and boots into charging mode. CU, Ricsi Gesendet: Sonntag, 24. August 2014 um 11:39 Uhr Von: "TSAREGORODTSEV, Yury" yury@bridgecommunication.co.uk An: baseband-devel@lists.osmocom.org Betreff: pirelli dp-l10 stuck Hi, everybody has same trouble that pirelli stuck after some usage ?