baseband-devel

baseband-devel@lists.osmocom.org

3 participants
2004 discussions

SIM-Max Tech's Super-SIM
by David A. Burgess 07 Mar '11

07 Mar '11

Hi - I apologize if this is slightly off topic, but has anyone here used a SIM-MaxTechnology "Super SIM" and its associated USB programmed to generate SIMs with a known A3/A8 and a known Ki? (I have been trying, but without success.) -- David

5 6

hi all
by 麦田守望 07 Mar '11

07 Mar '11

who tell me the osmocom .what is it i say it not to use

2 1

openmoko problem
by suraev＠stud.ntnu.no 06 Mar '11

06 Mar '11

Hi fellows. I'm having troubles running osmocom on neo freerunner: When I execure fluid flasher it works just fine, here is part of strace captured while it was waiting for me to power cycle modem: gettimeofday({1298877354, 793367}, NULL) = 0 gettimeofday({1298877354, 794341}, NULL) = 0 select(5, [4], NULL, NULL, {0, 12026}) = 0 (Timeout) ioctl(4, TCFLSH, 0) = 0 write(4, "<i\0", 3) = 3 gettimeofday({1298877354, 813368}, NULL) = 0 gettimeofday({1298877354, 814343}, NULL) = 0 select(5, [4], NULL, NULL, {0, 12025}) = 0 (Timeout) ioctl(4, TCFLSH, 0) = 0 write(4, "<i\0", 3) = 3 When I run osmocon - it waits endlessly completely ignoring power cycle: gettimeofday({1298875477, 254494}, NULL) = 0 gettimeofday({1298875477, 255514}, NULL) = 0 select(6, [3 4 5], [], [], {0, 48980}) = 0 (Timeout) gettimeofday({1298875477, 310972}, NULL) = 0 write(1, "Sending Calypso romloader beacon"..., 36) = 36 write(3, "<i", 2) = 2 gettimeofday({1298875477, 314494}, NULL) = 0 gettimeofday({1298875477, 315513}, NULL) = 0 select(6, [3 4 5], [], [], {0, 48981}) = 0 (Timeout) gettimeofday({1298875477, 370973}, NULL) = 0 write(1, "Sending Calypso romloader beacon"..., 36) = 36 write(3, "<i", 2) = 2 Can you help me to figure out what's wrong? Somebody succeeded in executing osmocon on moko? thanks, Max.

3 4

Newbie questions: Kc thru vty and CHAN_REQ
by David Ortega 06 Mar '11

06 Mar '11

Hi list !! Three newbie questions: 1.- What is the correct way to put Kc in the the sim-test ? the help command says: ki Set Key (Kc) on test card there are two options: - ki comp128 HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX (i think this is to fix the Ki value - 16bytes) - ki xor HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX HEX (this one need 12 bytes, when Kc it's only 8) 2.- In both calls type MOC and MTC i can't see the CHAN_REQ frame from MS in wireshark. I only get the RR IMM_ASS_CMD from BTS and the rest of the traffic: (from wireshark) to_MS 12:34:38.411650 GSMTAP (CCCH) (RR) Immediate Assignment from-MS 12:34:38.411675 LAPDm U, func=UI(DTAP) (RR) Measurement Report from-MS 12:34:38.411695 LAPDm U P, func=SABM(DTAP) (MM) CM Service Request to-MS 12:34:38.431273 GSMTAP (CCCH) (RR) Immediate Assignment (from my mobile app logs) Sun Mar 6 12:34:38 2011 <0001> gsm48_rr.c:363 new state idle -> connection pending Sun Mar 6 12:34:38 2011 <0001> gsm48_rr.c:1313 CHANNEL REQUEST: e0 (Orig TCH/F) (but i don't see this one in wireshark) Sun Mar 6 12:34:38 2011 <0004> gsm48_mm.c:887 new state MM IDLE, normal service -> wait for RR connection (MM connection) 3.- How must I activate the timestamp in the logs ? I'm using: //target->print_timestamp = 0; target->print_timestamp = 1; But i guess that there is an easy way without recompile... Thanx in advance !!

1 0

Re: MT6235/6140 and MT6516?
by burebista 04 Mar '11

04 Mar '11

Hy, do you have the MT6516 processors datasheet, could you please send it to me too? I tried asking MediaTek and Gigabyte (my pocket pc developer) but they refused me, I'm trying to port Haret to work on a pocket pc with this processor to boot linux. And another question: in the latest linux kernel i saw that the match_type for the MT65xx is there, but this processor is supported by the linux kernel? Thank You,

1 0

[PATCH] support for device specific setup (no need to patch UARTs for Pirelli DPL10)
by Leif Jakob 03 Mar '11

03 Mar '11

Hi, attached is a small patch to make board specific overrides (change UARTs). I'm experiencing some stability issues on my pirelli phone, sooner or later the layer1 resets and the phone boots again. Ah by the way: the wiki says "send and receive SMS". Did I miss something or is this not yet implemented (at least in "mobile")? Cheers Leif

1 0

AW: Fwd: gpsd support
by Andreas.Eversberg 02 Mar '11

02 Mar '11

hi dario, thanx for you work. here i still got problems, if i use gpsd 2.32: laptop src # make Making all in common make[1]: Entering directory `/root/osmocom-bb/src/host/layer23/src/common' CC gps.o gps.c: In function 'osmo_gpsd_cb': gps.c:73: warning: implicit declaration of function 'gps_waiting' gps.c: In function 'osmo_gpsd_open': gps.c:135: warning: implicit declaration of function 'gps_stream' gps.c:135: error: 'WATCH_ENABLE' undeclared (first use in this function) gps.c:135: error: (Each undeclared identifier is reported only once gps.c:135: error: for each function it appears in.) make[1]: *** [gps.o] Error 1 make[1]: Leaving directory `/root/osmocom-bb/src/host/layer23/src/common' make: *** [all-recursive] Error 1 also the patch will not work with the current head. the app_cell_log.c will fail to patch, but this is a minor problem. regards, andreas

1 0

AW: Help me I have a difficult problem
by Andreas.Eversberg 02 Mar '11

02 Mar '11

> This sound as a better solution, although I would suggest a .osmocom > directory and everything else as cache/whatever inside that directory, > otherwise it would be pretty dirty and messy as the project grows. what about this? : $HOME/.osmocom/mobile.cfg and for the stored band allocations: $HOME/.osmocom/xxxx.ba

3 3

mobile: config file in /etc/osmocom/osmocom.cfg
by Harald Welte 02 Mar '11

02 Mar '11

Hi all, I would like to propose moving the config file into something like ~/.osmocom/ and not put it in a system wide directory. The path in /etc/ is the only part of OsmocomBB that requires root privileges, and I don't really think that in a case of multiple users you would want to e.g. share stuff like the IMSI / Ki anyway. What do you think? -- - Harald Welte <laforge(a)gnumonks.org> http://laforge.gnumonks.org/ ============================================================================ "Privacy in residential applications is a desirable marketing option." (ETSI EN 300 175-7 Ch. A6)

3 4

openmoko test
by suraev＠stud.ntnu.no 02 Mar '11

02 Mar '11

Hello. I'm trying to run osmocom on neo freerunner (gta02) with shr-unstable. I've stopped fso framework and disabled fsogsmd, checked that nobody is using modem: fuser /dev/ttySAC0 After this I issue following: echo 1 > /sys/bus/platform/devices/gta02-pm-gsm.0/download ./osmocon -m romload -p /dev/ttySAC0 hello_world.highram.bin Sending Calypso romloader beacon... Sending Calypso romloader beacon... Sending Calypso romloader beacon... Sending Calypso romloader beacon... Sending Calypso romloader beacon... In separate console I run: echo 0 >/sys/bus/platform/devices/gta02-pm-gsm.0/power_on echo 1 >/sys/bus/platform/devices/gta02-pm-gsm.0/power_on but I keep getting "Sending Calypso romloader beacon..." on 1st one. Any ideas what am I doing wrong? Note: I got osmocon and hello_world.highram.bin at the same directory on moko to which I'm connected via ssh. Btw, do I need debug board in order to get /dev/ttyUSB0 when I connect freerunner to my laptop? best regards, Max.

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

baseband-devel