2 May
2012
2 May
'12
3:02 p.m.
Hi folks,
I'm still tinkering with this but am running into a bit of a wall with regards to P25
data.
These two lines are dumped to stderr using a call to the dump_cw function that I added to
the code. I'm only dumping the first 30 bytes for brevity:
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 5b 10 ba 16 de 2e 82 69 36 3d 98 1f 9b f8 8e c6
Based on what I've been able to determine so far, the first 48 bits are frame sync,
and they should be fixed at 0x5575f5ff77ff, which is what we see above.
The next 64 bits are supposed to be NID, which includes the DUID.
I could be wrong, but I believe the 02 (which alternates between 02 and 03 in the lines
below) at the 9th byte, is the status bit-pair that is interleaved every 70 bits (9 bytes
* 8 bits - 72 bits into the frame). Once removed, that shifts the remaining bits to the
left 2, which still leaves the NID essentially filled with zeroes except for the last two
bits. Immediately after the NID, however, the bits start flying again.
Does this seem normal? I can't really find any annotated hex dumps of a P25 frame to
try to line things up, but it seems that the NID should be populated with something other
than zeroes. If you bit shift the 15th bit 2 to the left, we'll get a parity bit set
every now and then (again, unless I'm messing something up), but nothing else.
I'm completely open to the fact that this could just be a bad signal, but I can get
very clear decodes of the voice if I force the type to LDU1 or LDU2, and I have never seen
anything but all zeroes here (across many minutes of decoded voice data)
Any thoughts?
--- In op25-dev(a)yahoogroups.com, "rrgsti" <bobrich@...> wrote:
Hi Matt!
Thanks for the info, it sounds like that is a very possible option. Is there a way to
see the state of the fsk4 demodulator? I did try running with the updated OP25.py that
Balint put out on Saturday (uses _op25.fsk4 instead of the Radio Raush module, and it
doesn't seem to behave any differently.
I did find dump_cw in op25_imbe_frame.h and used it to dump frames right before their
duid is read. I don't know if these will be meaningful, but I'll paste them in
here. Moments of silence have the clusters of 0xff's on the right, while portions
where there is audio has more random numbers.
I did note that about 9 bytes into this dump there is a byte that keeps flipping between
2 and 3. Is it possible this is where the DUID is (shifted a bit or two). Each row
starting with 0x55 0x75 is a new frame dumped, I only dump the first 32 bytes or so of
each one.
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 03 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 5b 10 ba 16 de 2e 82 69 36 3d 98 1f 9b f8 8e c6
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 74 35 56 de 42 7b ac 05 90 af 5a 0e 12 84 81 6b
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 52 0b 37 d6 c5 a6 11 79 56 f5 9b 1a 1e 22 8a 35
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 7e 2d f0 82 d0 4f f8 4d a2 61 34 94 52 a4 f8 ec
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 4e 46 60 ce 5d a8 8b 27 7f 62 78 ab c2 52 ee 0f
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 00 00 00 02 55 75 f5 ff 77 ff 2d 6f ae e2 78 2e
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 03 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff ff fc 25 ed
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 45 5e a4 8b 59 7f 74 31 29 f3 ed d2 36 6c fa 30
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 46 33 55 22 52 69 8e 51 5c 01 0b ae 5a eb 36 8f
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 5b 10 ba 16 de 2e 82 69 36 3d 98 1f 9a f8 8e c6
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 00 00 00 02 55 75 f5 ff 77 ff 2d 6f ae e2 78 2e
55 75 f5 ff 77 ff 00 00 02 00 00 00 00 00 01 26 2d 02 0f 68 4f ff ff ff ff ff fe fc 25 ed
--- In op25-dev(a)yahoogroups.com, Matt Robert <matt.robert80@> wrote:
Hi Bob,
Its more than likely a result of a bad signal. The FSK4 demod tends to output zeros when
it loses sync which is why the DUID is erroneously coming up as 0x00.
LDU1/2 are the two types of voice frames. LDU1 has signalling data embedded and LDU2 has
encryption sync data embedded.
The kludge diff posted below will work - but only for valid frames with a corrupt DUID
value.
I'm sure the root cause is the FSK4 demod isn't locking properly and causing a
bad DUID value to be outputted. I have seen similar behaviour in other areas of OP25 - for
example I was looking at the IV/MI value (72 bits) on a local P25 system here. Whenever
the demodulator ran out of talent, it would output steams of constant zeros.
Ohio MARCS is a Type 2 Smartzone Omnilink System with CAI compatible ASTRO voice channels
- so its essentially P25 compatible. The P25 CAI spec was based on the ASTRO CAI from the
same era, so its essentially the same thing.
Is the system running any form of simulcasting?Â
Cheers,
Matt
________________________________
From: rrgsti <bobrich@>
To: op25-dev(a)yahoogroups.com
Sent: Thursday, 26 April 2012 10:59 PM
Subject: [op25-dev] Re: OP25 GRC - Almost but not quite working
Â
Quick update from my end.
It looks like every frame coming out of the fsk4 demodulator (I'm assuming, still a
n00b here) is marked with a 'duid' of 0x0. Consequently, when data_unit.cc
initializes a new data_unit from the frame, it is always creating it as an HDU (P25
header) type. This then prevents the IMBE decoder from being executed b/c it's not a
voice data unit type (LDU1/LDU2 (no idea what these mean)).
I figured maybe it has something to do with our system (Ohio MARCS) not being full P25
compliant and not including metadata of any sort, so I just made the following change to
data_unit.cc and re-ran it:
--- op25-orig/blocks/src/lib/data_unit.cc 2012-04-24 10:31:29.139694592 -0400
+++ op25/blocks/src/lib/data_unit.cc 2012-04-26 08:12:35.183962129 -0400
@@ -39,7 +39,8 @@
uint8_t duid = extract(frame_body, 60, 64);
switch(duid) {
case 0x0:
- d = data_unit_sptr(new hdu(frame_body));
+ //d = data_unit_sptr(new hdu(frame_body));
+ d = data_unit_sptr(new ldu1(frame_body));
break;
case 0x3:
d = data_unit_sptr(new tdu(frame_body, false));
This seemed to sort of work as I now get rather garbled, but intelligible, audio from the
decoder.
I've uploaded the baseband capture (1Msps) and resulting audio .wav file that I get
at the following URLS:
http://s3.amazonaws.com/public-xrp/p25.iq.bz2
http://s3.amazonaws.com/public-xrp/p25.wav
Not sure if this is of any use, but it is encouraging to hear voices at least. :)
Thanks!
Bob
--- In op25-dev(a)yahoogroups.com, Andy Knitt <andyknitt@> wrote:
It looks like imbe_decoder_factory.cc in OP25 defaults to
'software_imbe_decoder'. I manually changed the IMBE environment variable
to "soft" and confirmed it with printenv, but I'm still getting a flat
line
at the output of the OP25 block. Any other ideas?
Thanks,
Andy
On Mon, Apr 23, 2012 at 11:47 PM, Balint <balint256@> wrote:
**
I *still* haven't checked out the latest code, but in my old code the
default voice frame output was (null?).****
There are options for file output, null, external (hardware) decoder and
internal decoder. You used to be able to spec this on the command line as
an environment variable:****
export IMBE=soft****
I changed my default to be the internal decoder (see
`imbe_decoder_factory.cc').****
** **
*From:* op25-dev(a)yahoogroups.com [mailto:op25-dev@yahoogroups.com] *On
Behalf Of *Andy Knitt
*Sent:* Tuesday, 24 April 2012 12:45 PM
*To:* op25-dev(a)yahoogroups.com
*Subject:* [op25-dev] OP25 GRC - Almost but not quite working****
** **
****
I have the OP25 GRC demo that Balint provided up and running.
Everything seems to working except I'm not getting any audio out of
the OP25 block. I'm getting the "four line" output from the dibit
output port when there is traffic on the channel, and the autotune
output is outputting data. However, no audio. I put a scope on the
audio output and it's a flat line at zero, even when the dibit output
is "four lines". Any tips on how to further troubleshoot?
Thanks,
Andy****
****