[M] Change in osmo-bts[master]: sysmo: generate empty TCH/H payload on FACCH/H Rx

falconia has submitted this change. ( https://gerrit.osmocom.org/c/osmo-bts/+/37647?usp=email ) Change subject: sysmo: generate empty TCH/H payload on FACCH/H Rx ...................................................................... sysmo: generate empty TCH/H payload on FACCH/H Rx When sysmoBTS PHY decodes TCH UL Rx as FACCH, it sends only one PH-DATA.ind for the FACCH, but none for TCH. This case was handled correctly for TCH/F in 2023-03, but FACCH/H has not been handled correctly until now. Change-Id: Id6d966348fb2be084485279e75480f98f46e464b --- M src/osmo-bts-sysmo/l1_if.c 1 file changed, 35 insertions(+), 16 deletions(-) Approvals: Jenkins Builder: Verified fixeria: Looks good to me, but someone else must approve pespin: Looks good to me, approved diff --git a/src/osmo-bts-sysmo/l1_if.c b/src/osmo-bts-sysmo/l1_if.c index 9ca1c32..aa4a739 100644 --- a/src/osmo-bts-sysmo/l1_if.c +++ b/src/osmo-bts-sysmo/l1_if.c @@ -987,23 +987,28 @@ return rc; } - /* If we got FACCH, the RTP clock needs to account for it, - * and if we have rtp continuous-streaming enabled, - * an actual BFI packet will be emitted. + /* When TCH UL receiver in sysmoBTS PHY detects FACCH, + * it behaves as follows (observed): * - * Only the case of TCH/F is currently handled; the task of - * supporting TCH/H is left as a FIXME for other/later - * developers. The difficulty with supporting FACCH/H is that - * only one GsmL1_Sapi_FacchH message will be received, - * covering 40 ms of time, but two RTP "tick" output calls - * will need to be made, with appropriately adjusted frame - * numbers. As a further consideration for rtp continuous-streaming - * mode, having the two RTP BFI packets sent directly back to back, - * as opposed to proper 20 ms timing, may be so undesirable - * that some deployments may rather disable TCH/H (use only TCH/F) - * than deal with the extra pain, or use TCH/H only on SDR-based - * BTS with osmo-bts-trx where correct timing is easily achieved. */ - if (data_ind->sapi == GsmL1_Sapi_FacchF) + * - In each 20 ms window (both TCH/F and TCH/H), a single + * PH-DATA.ind arrives. + * - In the case of TCH/F, this PH-DATA.ind carries GsmL1_Sapi_FacchF + * instead of GsmL1_Sapi_TchF. + * - In the case of TCH/H, the PH-DATA.ind for block 0 carries + * GsmL1_Sapi_FacchH instead of GsmL1_Sapi_TchH. However, + * in the following 20 ms window (block 1 of FACCH/H) + * a PH-DATA.ind with GsmL1_Sapi_TchH arrives as normal. + * Typically the latter PHY message carries a BFI (0 length payload), + * but nonzero payloads have also been observed under some conditions. + * (The latter case remains to be investigated further.) + * + * In those 20 ms windows where we receive PH-DATA.ind for FACCH + * instead of the usual TCH kind, we need to pass an empty payload + * to the upper layers so we can produce the correct effect in + * the outgoing RTP stream depending on configuration. + */ + if (data_ind->sapi == GsmL1_Sapi_FacchF || + data_ind->sapi == GsmL1_Sapi_FacchH) l1if_tch_rx_facch(trx, chan_nr, l1p_msg); /* fill L1SAP header */ -- To view, visit https://gerrit.osmocom.org/c/osmo-bts/+/37647?usp=email To unsubscribe, or for help writing mail filters, visit https://gerrit.osmocom.org/settings Gerrit-Project: osmo-bts Gerrit-Branch: master Gerrit-Change-Id: Id6d966348fb2be084485279e75480f98f46e464b Gerrit-Change-Number: 37647 Gerrit-PatchSet: 1 Gerrit-Owner: falconia <falcon(a)freecalypso.org> Gerrit-Reviewer: Jenkins Builder Gerrit-Reviewer: falconia <falcon(a)freecalypso.org> Gerrit-Reviewer: fixeria <vyanitskiy(a)sysmocom.de> Gerrit-Reviewer: pespin <pespin(a)sysmocom.de> Gerrit-MessageType: merged