24 Nov
2023
24 Nov
'23
9:16 a.m.
osmith has submitted this change. (
https://gerrit.osmocom.org/c/docker-playground/+/35103?usp=email )
Change subject: open5gs configs: remove comments
......................................................................
open5gs configs: remove comments
A lot of these comments got outdated with recent config changes
in the related PR. Instead of syncing the comments again and having a
big diff, remove the comments once and then only have diffs of
actual config changes in future patches. This will make it easier to
maintain these configs.
Related: https://github.com/open5gs/open5gs/pull/2739
Change-Id: I67c2a198b9682e15e23a466380e62a976e6236cd
---
M ttcn3-ggsn-test/ogs/open5gs-smf.yaml
M ttcn3-ggsn-test/ogs/open5gs-upf.yaml
M ttcn3-hss-test-ogs/ogs/open5gs-hss.yaml
M ttcn3-mme-test-ogs/ogs/open5gs-mme.yaml
M ttcn3-pgw-test/open5gs-nrf.yaml
M ttcn3-pgw-test/open5gs-smf.yaml
M ttcn3-pgw-test/open5gs-upf.yaml
7 files changed, 32 insertions(+), 2,973 deletions(-)
Approvals:
fixeria: Looks good to me, but someone else must approve
daniel: Looks good to me, approved
Jenkins Builder: Verified
diff --git a/ttcn3-ggsn-test/ogs/open5gs-smf.yaml b/ttcn3-ggsn-test/ogs/open5gs-smf.yaml
index 045c585..afb5cf2 100644
--- a/ttcn3-ggsn-test/ogs/open5gs-smf.yaml
+++ b/ttcn3-ggsn-test/ogs/open5gs-smf.yaml
@@ -1,63 +1,8 @@
-#
-# o Set OGS_LOG_INFO to all domain level
-# - If `level` is omitted, the default level is OGS_LOG_INFO)
-# - If `domain` is omitted, the all domain level is set from 'level'
-# (Default values are used, so no configuration is required)
-#
-# o Set OGS_LOG_ERROR to all domain level
-# - `level` can be set with none, fatal, error, warn, info, debug, trace
-# logger:
-# level: error
-#
-# o Set OGS_LOG_DEBUG to mme/emm domain level
-# logger:
-# level: debug
-# domain: mme,emm
-#
-# o Set OGS_LOG_TRACE to all domain level
-# logger:
-# level: trace
-# domain: core,sbi,ausf,event,tlv,mem,sock
-#
+# See https://github.com/open5gs/open5gs/blob/main/configs/open5gs/smf.yaml.in
+
logger:
level: info
-#
-# o TLS enable/disable
-# sbi:
-# server|client:
-# no_tls: false|true
-# - false: (Default) Use TLS
-# - true: TLS disabled
-#
-# o Verification enable/disable
-# sbi:
-# server|client:
-# no_verify: false|true
-# - false: (Default) Verify the PEER
-# - true: Skip the verification step
-#
-# o Server-side does not use TLS
-# sbi:
-# server:
-# no_tls: true
-#
-# o Client-side skips the verification step
-# sbi:
-# client:
-# no_verify: true
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-#
-# o Use the specified certificate while verifying the client
-# sbi:
-# server
-# cacert: /etc/open5gs/tls/ca.crt
-#
-# o Use the specified certificate while verifying the server
-# sbi:
-# client
-# cacert: /etc/open5gs/tls/ca.crt
-#
+
sbi:
server:
no_tls: true
@@ -70,525 +15,6 @@
key: /etc/open5gs/tls/smf.key
cert: /etc/open5gs/tls/smf.crt
-#
-# <SBI Server>
-#
-# o SBI Server(http://<all address available>:80)
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-#
-# o SBI Server(http://<any address>:7777)
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr:
-# - 0.0.0.0
-# - ::0
-# port: 7777
-#
-# o SBI Server(https://<all address available>:443)
-# sbi:
-# server:
-# key: /etc/open5gs/tls/smf.key
-# cert: /etc/open5gs/tls/smf.crt
-# smf:
-# sbi:
-#
-# o SBI Server(https://127.0.0.4:443, https://[::1]:443) without verification
-# sbi:
-# server:
-# no_verify: true
-# key: /etc/open5gs/tls/smf.key
-# cert: /etc/open5gs/tls/smf.crt
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# - addr: ::1
-#
-# o SBI Server(https://smf.open5gs.org:443)
-# Use the specified certificate while verifying the client
-#
-# sbi:
-# server:
-# cacert: /etc/open5gs/tls/ca.crt
-# key: /etc/open5gs/tls/smf.key
-# cert: /etc/open5gs/tls/smf.crt
-# smf:
-# sbi:
-# - name: smf.open5gs.org
-#
-# o SBI Server(http://127.0.0.4:7777)
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-#
-# o SBI Server(http://<eth0 IP address>:80)
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - dev: eth0
-#
-# o Provide custom SBI address to be advertised to NRF
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - dev: eth0
-# advertise: open5gs-smf.svc.local
-#
-# o Another example of advertising on NRF
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: localhost
-# advertise:
-# - 127.0.0.99
-# - ::1
-#
-# o SBI Option (Default)
-# - tcp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# addr: 127.0.0.4
-# option:
-# tcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
-#
-# <NF Service>
-#
-# o NF Service Name(Default : all NF services available)
-# smf:
-# service_name:
-#
-# o NF Service Name(Only some NF services are available)
-# smf:
-# service_name:
-# - nsmf-pdusession
-#
-# <NF Discovery Query Parameter>
-#
-# o (Default) If you do not set Query Parameter as shown below,
-#
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-#
-# - 'service-names' is included.
-#
-# o Service-Names are not included
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-# discovery:
-# option:
-# no_service_names: false
-#
-# o To remove 'service-names' from URI query parameters in NS Discovery
-# no_service_names: true
-#
-# * For Indirect Communication with Delegated Discovery,
-# 'service-names' is always included in the URI query parameter.
-# * That is, 'no_service_names' has no effect.
-#
-# <For Indirect Communication with Delegated Discovery>
-#
-# o (Default) If you do not set Delegated Discovery as shown below,
-#
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-#
-# - Use SCP if SCP available. Otherwise NRF is used.
-# => App fails if both NRF and SCP are unavailable.
-#
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-# discovery:
-# delegated: auto
-#
-# o To use SCP always => App fails if no SCP available.
-# delegated: yes
-#
-# o Don't use SCP server => App fails if no NRF available.
-# delegated: no
-#
-# <PFCP Server>
-#
-# o PFCP Server(127.0.0.4:8805, ::1:8805)
-# smf:
-# pfcp:
-# - addr: 127.0.0.4
-# - addr: ::1
-#
-# o PFCP-U Server(127.0.0.1:2152, [::1]:2152)
-# smf:
-# pfcp:
-# name: localhost
-#
-# o PFCP Option (Default)
-# - so_bindtodevice : NULL
-#
-# smf:
-# pfcp:
-# addr: 127.0.0.4
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <GTP-C Server>
-#
-# o GTP-C Server(127.0.0.4:2123, [fd69:f21d:873c:fa::3]:2123)
-# smf:
-# gtpc:
-# addr:
-# - 127.0.0.4
-# - fd69:f21d:873c:fa::3
-#
-# o On SMF, Same configuration
-# (127.0.0.4:2123, [fd69:f21d:873c:fa::3]:2123).
-# smf:
-# gtpc:
-# - addr: 127.0.0.4
-# - addr: fd69:f21d:873c:fa::3
-#
-# o GTP-C Option (Default)
-# - so_bindtodevice : NULL
-#
-# smf:
-# gtpc:
-# addr: 127.0.0.4
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <GTP-U Server>>
-#
-# o GTP-U Server(127.0.0.4:2152, [::1]:2152)
-# smf:
-# gtpu:
-# - addr: 127.0.0.4
-# - addr: ::1
-#
-# o GTP-U Server(127.0.0.1:2152, [::1]:2152)
-# smf:
-# gtpu:
-# name: localhost
-#
-# o GTP-U Option (Default)
-# - so_bindtodevice : NULL
-#
-# smf:
-# gtpu:
-# addr: 127.0.0.4
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <Metrics Server>
-#
-# o Metrics Server(http://<any address>:9090)
-# smf:
-# metrics:
-# - addr: 0.0.0.0
-# port: 9090
-#
-# <Subnet for UE Pool>
-#
-# o IPv4 Pool
-# smf:
-# subnet:
-# addr: 10.45.0.1/16
-#
-# o IPv4/IPv6 Pool
-# smf:
-# subnet:
-# - addr: 10.45.0.1/16
-# - addr: 2001:db8:cafe::1/48
-#
-#
-# o Specific DNN/APN(e.g 'ims') uses 10.46.0.1/16, 2001:db8:babe::1/48
-# ; If the UE has unknown DNN/APN(not internet/ims), SMF/UPF will crash.
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 2001:db8:cafe::1/48
-# dnn: internet
-# - addr: 10.46.0.1/16
-# dnn: ims
-# - addr: 2001:db8:babe::1/48
-# dnn: ims
-#
-# o Specific DNN/APN with the FALLBACK SUBNET(10.47.0.1/16)
-# ; Note that put the FALLBACK SUBNET last to avoid SMF/UPF crash.
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 10.46.0.1/16
-# dnn: ims
-# - addr: 10.50.0.1/16 ## FALLBACK SUBNET
-#
-# o Pool Range Sample
-# smf:
-# subnet:
-# - addr: 10.45.0.1/24
-# range: 10.45.0.100-10.45.0.200
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/24
-# range:
-# - 10.45.0.5-10.45.0.50
-# - 10.45.0.100-
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/24
-# range:
-# - -10.45.0.200
-# - 10.45.0.210-10.45.0.220
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/16
-# range:
-# - 10.45.0.100-10.45.0.200
-# - 10.45.1.100-10.45.1.200
-# - addr: 2001:db8:cafe::1/48
-# range:
-# - 2001:db8:cafe:a0::0-2001:db8:cafe:b0::0
-# - 2001:db8:cafe:c0::0-2001:db8:cafe:d0::0
-#
-# <Domain Name Server>
-#
-# o Primary/Secondary can be configured. Others are ignored.
-#
-# smf:
-# dns:
-# - 8.8.8.8
-# - 8.8.4.4
-# - 2001:4860:4860::8888
-# - 2001:4860:4860::8844
-#
-# <MTU Size>
-#
-# o Provisioning a limit on the size of the packets sent by the MS
-# to avoid packet fragmentation in the backbone network
-# between the MS and the GGSN/PGW and/or across the (S)Gi reference point)
-# when some of the backbone links does not support
-# packets larger then 1500 octets
-#
-# <P-CSCF>
-#
-# o Proxy Call Session Control Function
-#
-# smf:
-# p-cscf:
-# - 127.0.0.1
-# - ::1
-#
-# <CTF>
-#
-# o Gy interface parameters towards OCS.
-# o enabled:
-# o auto: Default. Use Gy only if OCS available among Diameter peers
-# o yes: Use Gy always;
-# reject subscribers if no OCS available among Diameter peers
-# o no: Don't use Gy interface if there is an OCS available
-#
-# smf:
-# ctf:
-# enabled: auto|yes|no
-#
-#
-# <SMF Selection - 5G Core only>
-# 1. SMF sends SmfInfo(S-NSSAI, DNN, TAI) to the NRF
-# 2. NRF responds to AMF with SmfInfo during NF-Discovery.
-# 3. AMF selects SMF based on S-NSSAI, DNN and TAI in SmfInfo.
-#
-# Note that if there is no SmfInfo, any AMF can select this SMF.
-#
-# o S-NSSAI[SST:1] and DNN[internet] - At least 1 DNN is required in S-NSSAI
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# dnn:
-# - internet
-#
-# o S-NSSAI[SST:1 SD:009000] and DNN[internet or ims]
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# sd: 009000
-# dnn:
-# - internet
-# - ims
-#
-# o S-NSSAI[SST:1] and DNN[internet] and TAI[PLMN-ID:99970 TAC:1]
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac: 1
-#
-# o If any of conditions below are met:
-# - S-NSSAI[SST:1] and DNN[internet] and TAI[PLMN-ID:99970 TAC:1-9]
-# - S-NSSAI[SST:2 SD:000080] and DNN[internet or ims]
-# - S-NSSAI[SST:4] and DNN[internet] and TAI[PLMN-ID:99970 TAC:10-20,30-40]
-#
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# range:
-# - 1-9
-# - s_nssai:
-# - sst: 2
-# sd: 000080
-# dnn:
-# - internet
-# - ims
-# - s_nssai:
-# - sst: 4
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# range:
-# - 10-20
-# - 30-40
-#
-# o Complex Example
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# dnn:
-# - internet
-# - sst: 1
-# sd: 000080
-# dnn:
-# - internet
-# - ims
-# - sst: 1
-# sd: 009000
-# dnn:
-# [internet, ims]
-# - sst: 2
-# dnn:
-# - internet
-# - sst: 3
-# sd: 123456
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac: [1, 2, 3]
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac: 4
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac:
-# - 5
-# - 6
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# range:
-# - 100-200
-# - 300-400
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# range:
-# - 500-600
-# - 700-800
-# - 900-1000
-# - s_nssai:
-# - sst: 4
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac: 99
-#
-# <Security Indication - 5G Core only>
-#
-# According to 3GPP TS38.413 Section 9.3.1.27,
-# Security Indication IE may be instructed to 5G gNB.
-#
-# If you set the security_indication in smf.yaml,
-# this information is delivered using PDU Session Resource Request Transfer IE
-#
-# smf:
-# security_indication:
-# integrity_protection_indication: required|preferred|not-needed
-# confidentiality_protection_indication: required|preferred|not-needed
-# maximum_integrity_protected_data_rate_uplink: bitrate64kbs|maximum-UE-rate
-# maximum_integrity_protected_data_rate_downlink: bitrate64kbs|maximum-UE-rate
-#
smf:
sbi:
- addr: 172.18.3.201
@@ -626,262 +52,23 @@
enabled: auto
freeDiameter: /data/freediameter.conf
-#
-# <SBI Client>>
-#
-# o SBI Client(http://127.0.1.10:7777)
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr: 127.0.1.10
-# port: 7777
-#
-# o SBI Client(https://127.0.1.10:443, https://[::1]:443) without verification
-# sbi:
-# client:
-# no_verify: true
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# scp:
-# sbi:
-# - addr: 127.0.1.10
-# - addr: ::1
-#
-# o SBI Client(https://scp.open5gs.org:443)
-# Use the specified certificate while verifying the server
-#
-# sbi:
-# client:
-# cacert: /etc/open5gs/tls/ca.crt
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# scp:
-# sbi:
-# - name: scp.open5gs.org
-#
-# o SBI Client(http://[fd69:f21d:873c:fb::1]:80)
-# If prefer_ipv4 is true, http://127.0.1.10:80 is selected.
-#
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr:
-# - 127.0.1.10
-# - fd69:f21d:873c:fb::1
-#
-# o SBI Option (Default)
-# - tcp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr: 127.0.1.10
-# option:
-# tcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
-#
scp:
sbi:
- addr: 127.0.1.10
port: 7777
-#
-# <SBI Client>>
-#
-# o SBI Client(http://127.0.0.10:7777)
-# sbi:
-# client:
-# no_tls: true
-# nrf:
-# sbi:
-# addr: 127.0.0.10
-# port: 7777
-#
-# o SBI Client(https://127.0.0.10:443, https://[::1]:443) without verification
-# sbi:
-# client:
-# no_verify: true
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# nrf:
-# sbi:
-# - addr: 127.0.0.10
-# - addr: ::1
-#
-# o SBI Client(https://nrf.open5gs.org:443)
-# Use the specified certificate while verifying the server
-#
-# sbi:
-# client:
-# cacert: /etc/open5gs/tls/ca.crt
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# nrf:
-# sbi:
-# - name: nrf.open5gs.org
-#
-# o SBI Client(http://[fd69:f21d:873c:fa::1]:80)
-# If prefer_ipv4 is true, http://127.0.0.10:80 is selected.
-#
-# sbi:
-# addr:
-# - 127.0.0.10
-# - fd69:f21d:873c:fa::1
-#
-# o SBI Option (Default)
-# - tcp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# sbi:
-# client:
-# no_tls: true
-# nrf:
-# sbi:
-# addr: 127.0.0.10
-# option:
-# tcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
nrf:
sbi:
- addr:
- 172.18.3.201
port: 7777
-#
-# <PFCP Client>>
-#
-# o PFCP Client(127.0.0.7:8805)
-# upf:
-# pfcp:
-# addr: 127.0.0.7
-#
-# <UPF Selection>
-#
-# o Round-Robin
-# (note that round robin can be disabled for a particular node
-# by setting flag 'rr' to 0)
-#
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# - addr: 127.0.0.12
-# rr: 0
-# - addr: 127.0.0.19
-#
-# o UPF selection by eNodeB TAC
-# (either single TAC or multiple TACs, DECIMAL representation)
-#
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# tac: 1
-# - addr: 127.0.0.12
-# tac: [3,5,8]
-#
-# o UPF selection by UE's DNN/APN (either single DNN/APN or multiple DNNs/APNs)
-#
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# dnn: ims
-# - addr: 127.0.0.12
-# dnn: [internet, web]
-#
-# o UPF selection by CellID(e_cell_id: 28bit, nr_cell_id: 36bit)
-# (either single enb_id or multiple enb_ids, HEX representation)
-#
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# e_cell_id: 463
-# - addr: 127.0.0.12
-# nr_cell_id: [123456789, 9413]
-#
upf:
pfcp:
- addr: 172.18.3.222
-#
-# o Disable use of IPv4 addresses (only IPv6)
-# parameter:
-# no_ipv4: true
-#
-# o Disable use of IPv6 addresses (only IPv4)
-# parameter:
-# no_ipv6: true
-#
-# o Prefer IPv4 instead of IPv6 for estabishing new GTP connections.
-# parameter:
-# prefer_ipv4: true
-#
-# o Disable selection of UPF PFCP in Round-Robin manner
-# parameter:
-# no_pfcp_rr_select: true
-#
-# o Legacy support for pre-release LTE 11 devices
-# - Omits adding local address in packet filters for compatibility
-# parameter:
-# no_ipv4v6_local_addr_in_packet_filter: true
-#
parameter:
-#
-# o Maximum Number of UE
-# max:
-# ue: 1024
-#
-# o Maximum Number of Peer(S1AP/NGAP, DIAMETER, GTP, PFCP or SBI)
-# max:
-# peer: 64
-#
-# o Maximum Number of GTP peer nodes per SGWC/SMF
-# max:
-# gtp_peer: 64
-#
max:
-#
-# o NF Instance Heartbeat (Default : 0)
-# NFs will not send heart-beat timer in NFProfile
-# NRF will send heart-beat timer in NFProfile
-# (Default values are used, so no configuration is required)
-#
-# o NF Instance Heartbeat (20 seconds)
-# NFs will send heart-beat timer (20 seconds) in NFProfile
-# NRF can change heart-beat timer in NFProfile
-# time:
-# nf_instance:
-# heartbeat: 20
-#
-# o Message Wait Duration (Default : 10,000 ms = 10 seconds)
-# (Default values are used, so no configuration is required)
-#
-# o Message Wait Duration (3000 ms)
-# time:
-# message:
-# duration: 3000
-#
-# o Handover Wait Duration (Default : 300 ms)
-# Time to wait for SMF to send
-# PFCP Session Modification Request(Remove Indirect Tunnel) to the UPF
-# after sending Nsmf_PDUSession_UpdateSMContext Response(hoState:COMPLETED)
-# (Default values are used, so no configuration is required)
-#
-# o Handover Wait Duration (500ms)
-# time:
-# handover:
-# duration: 500
time:
diff --git a/ttcn3-ggsn-test/ogs/open5gs-upf.yaml b/ttcn3-ggsn-test/ogs/open5gs-upf.yaml
index c82a80c..73e1bac 100644
--- a/ttcn3-ggsn-test/ogs/open5gs-upf.yaml
+++ b/ttcn3-ggsn-test/ogs/open5gs-upf.yaml
@@ -1,192 +1,8 @@
-#
-# o Set OGS_LOG_INFO to all domain level
-# - If `level` is omitted, the default level is OGS_LOG_INFO)
-# - If `domain` is omitted, the all domain level is set from 'level'
-# (Default values are used, so no configuration is required)
-#
-# o Set OGS_LOG_ERROR to all domain level
-# - `level` can be set with none, fatal, error, warn, info, debug, trace
-# logger:
-# level: error
-#
-# o Set OGS_LOG_DEBUG to mme/emm domain level
-# logger:
-# level: debug
-# domain: mme,emm
-#
-# o Set OGS_LOG_TRACE to all domain level
-# logger:
-# level: trace
-# domain: core,sbi,ausf,event,tlv,mem,sock
-#
+# See https://github.com/open5gs/open5gs/blob/main/configs/open5gs/upf.yaml.in
+
logger:
level: info
-#
-# <PFCP Server>
-#
-# o PFCP Server(127.0.0.7:8805, ::1:8805)
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# - addr: ::1
-#
-# o PFCP-U Server(127.0.0.1:2152, [::1]:2152)
-# upf:
-# pfcp:
-# name: localhost
-#
-# o PFCP Option (Default)
-# - so_bindtodevice : NULL
-#
-# upf:
-# pfcp:
-# addr: 127.0.0.7
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <GTP-U Server>>
-#
-# o GTP-U Server(127.0.0.7:2152, [::1]:2152)
-# upf:
-# gtpu:
-# - addr: 127.0.0.7
-# - addr: ::1
-#
-# o GTP-U Server(127.0.0.1:2152, [::1]:2152)
-# upf:
-# gtpu:
-# name: localhost
-#
-# o User Plane IP Resource information
-# upf:
-# gtpu:
-# - addr:
-# - 127.0.0.7
-# - ::1
-# teid_range_indication: 4
-# teid_range: 10
-# network_instance: internet
-# source_interface: 0
-# - addr: 127.0.10.4
-# teid_range_indication: 4
-# teid_range: 5
-# network_instance: ims
-# source_interface: 1
-#
-# o Provide custom UPF GTP-U address to be advertised inside NGAP messages
-# upf:
-# gtpu:
-# - addr: 10.4.128.21
-# advertise: 172.24.15.30
-#
-# upf:
-# gtpu:
-# - addr: 10.4.128.21
-# advertise:
-# - 127.0.0.1
-# - ::1
-#
-# upf:
-# gtpu:
-# - addr: 10.4.128.21
-# advertise: upf1.5gc.mnc001.mcc001.3gppnetwork.org
-#
-# upf:
-# gtpu:
-# - dev: ens3
-# advertise: upf1.5gc.mnc001.mcc001.3gppnetwork.org
-#
-# o GTP-U Option (Default)
-# - so_bindtodevice : NULL
-#
-# upf:
-# gtpu:
-# addr: 127.0.0.7
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <Subnet for UE network>
-#
-# Note that you need to setup your UE network using TUN device.
-# (ogstun, ogstun2, ogstunX, ..)
-#
-# o IPv4 Pool
-# $ sudo ip addr add 10.45.0.1/16 dev ogstun
-#
-# upf:
-# subnet:
-# addr: 10.45.0.1/16
-#
-# o IPv4/IPv6 Pool
-# $ sudo ip addr add 10.45.0.1/16 dev ogstun
-# $ sudo ip addr add 2001:db8:cafe::1/48 dev ogstun
-#
-# upf:
-# subnet:
-# - addr: 10.45.0.1/16
-# - addr: 2001:db8:cafe::1/48
-#
-#
-# o Specific DNN/APN(e.g 'ims') uses 10.46.0.1/16, 2001:db8:babe::1/48
-# All other APNs use 10.45.0.1/16, 2001:db8:cafe::1/48
-# $ sudo ip addr add 10.45.0.1/16 dev ogstun
-# $ sudo ip addr add 10.46.0.1/16 dev ogstun
-# $ sudo ip addr add 2001:db8:cafe::1/48 dev ogstun
-# $ sudo ip addr add 2001:db8:babe::1/48 dev ogstun
-#
-# ; If the UE has unknown DNN/APN(not internet/ims), SMF/UPF will crash.
-#
-# upf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 2001:db8:cafe::1/48
-# dnn: internet
-# - addr: 10.46.0.1/16
-# dnn: ims
-# - addr: 2001:db8:babe::1/48
-# dnn: ims
-#
-# o Specific DNN/APN with the FALLBACK SUBNET(10.47.0.1/16)
-# ; Note that put the FALLBACK SUBNET last to avoid SMF/UPF crash.
-#
-# upf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 10.46.0.1/16
-# dnn: ims
-# - addr: 10.50.0.1/16 ## FALLBACK SUBNET
-#
-# o Multiple Devices (default: ogstun)
-# $ sudo ip addr add 10.45.0.1/16 dev ogstun
-# $ sudo ip addr add 2001:db8:cafe::1/48 dev ogstun2
-# $ sudo ip addr add 10.46.0.1/16 dev ogstun3
-# $ sudo ip addr add 2001:db8:babe::1/48 dev ogstun3
-#
-# upf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 2001:db8:cafe::1/48
-# dnn: internet
-# dev: ogstun2
-# - addr: 10.46.0.1/16
-# dnn: ims
-# dev: ogstun3
-# - addr: 2001:db8:babe::1/48
-# dnn: ims
-# dev: ogstun3
-#
-# <Metrics Server>
-#
-# o Metrics Server(http://<any address>:9090)
-# upf:
-# metrics:
-# - addr: 0.0.0.0
-# port: 9090
-#
upf:
pfcp:
- addr: 172.18.3.222
@@ -209,54 +25,12 @@
dnn: inet46
dev: ogstun46
-#
-# <PFCP Client>>
-#
-# o PFCP Client(127.0.0.4:8805)
-# smf:
-# pfcp:
-# addr: 127.0.0.4
-#
smf:
pfcp:
- addr: 172.18.3.201
-#
-# o Number of output streams per SCTP associations.
-# parameter:
-# sctp_streams: 30
-#
-# o Disable use of IPv4 addresses (only IPv6)
-# parameter:
-# no_ipv4: true
-#
-# o Disable use of IPv6 addresses (only IPv4)
-# parameter:
-# no_ipv6: true
-#
-# o Prefer IPv4 instead of IPv6 for estabishing new GTP connections.
-# parameter:
-# prefer_ipv4: true
-#
parameter:
-#
-# o Maximum Number of UE
-# max:
-# ue: 1024
-#
-# o Maximum Number of Peer(S1AP/NGAP, DIAMETER, GTP, PFCP or SBI)
-# max:
-# peer: 64
-#
max:
-#
-# o Message Wait Duration (Default : 10,000 ms = 10 seconds)
-# (Default values are used, so no configuration is required)
-#
-# o Message Wait Duration (3000 ms)
-# time:
-# message:
-# duration: 3000
time:
diff --git a/ttcn3-hss-test-ogs/ogs/open5gs-hss.yaml
b/ttcn3-hss-test-ogs/ogs/open5gs-hss.yaml
index 5f38e58..8d1f42e 100644
--- a/ttcn3-hss-test-ogs/ogs/open5gs-hss.yaml
+++ b/ttcn3-hss-test-ogs/ogs/open5gs-hss.yaml
@@ -1,63 +1,13 @@
+# See https://github.com/open5gs/open5gs/blob/main/configs/open5gs/hss.yaml.in
+
db_uri: mongodb://172.18.3.103/open5gs
-#
-# o Set OGS_LOG_INFO to all domain level
-# - If `level` is omitted, the default level is OGS_LOG_INFO)
-# - If `domain` is omitted, the all domain level is set from 'level'
-# (Default values are used, so no configuration is required)
-#
-# o Set OGS_LOG_ERROR to all domain level
-# - `level` can be set with none, fatal, error, warn, info, debug, trace
-# logger:
-# level: error
-#
-# o Set OGS_LOG_DEBUG to mme/emm domain level
-# logger:
-# level: debug
-# domain: mme,emm
-#
-# o Set OGS_LOG_TRACE to all domain level
-# logger:
-# level: trace
-# domain: core,sbi,ausf,event,tlv,mem,sock
-#
logger:
level: trace
hss:
freeDiameter: /data/freediameter.conf
-#
-# hss:
-# sms_over_ims: "sip:smsc.mnc001.mcc001.3gppnetwork.org:7060;transport=tcp"
-#
-
-#
-# o Disable use of IPv4 addresses (only IPv6)
-# parameter:
-# no_ipv4: true
-#
-# o Disable use of IPv6 addresses (only IPv4)
-# parameter:
-# no_ipv6: true
-#
-# o Prefer IPv4 instead of IPv6 for estabishing new GTP connections.
-# parameter:
-# prefer_ipv4: true
-#
-# o Use MongoDB Change Stream
-# parameter:
-# use_mongodb_change_stream: true
-#
parameter:
-#
-# o Maximum Number of UE
-# max:
-# ue: 1024
-#
-# o Maximum Number of Peer(S1AP/NGAP, DIAMETER, GTP, PFCP or SBI)
-# max:
-# peer: 64
-#
max:
diff --git a/ttcn3-mme-test-ogs/ogs/open5gs-mme.yaml
b/ttcn3-mme-test-ogs/ogs/open5gs-mme.yaml
index 74229ea..35b718d 100644
--- a/ttcn3-mme-test-ogs/ogs/open5gs-mme.yaml
+++ b/ttcn3-mme-test-ogs/ogs/open5gs-mme.yaml
@@ -1,323 +1,8 @@
-#
-# o Set OGS_LOG_INFO to all domain level
-# - If `level` is omitted, the default level is OGS_LOG_INFO)
-# - If `domain` is omitted, the all domain level is set from 'level'
-# (Default values are used, so no configuration is required)
-#
-# o Set OGS_LOG_ERROR to all domain level
-# - `level` can be set with none, fatal, error, warn, info, debug, trace
-# logger:
-# level: error
-#
-# o Set OGS_LOG_DEBUG to mme/emm domain level
-# logger:
-# level: debug
-# domain: mme,emm
-#
-# o Set OGS_LOG_TRACE to all domain level
-# logger:
-# level: trace
-# domain: core,sbi,ausf,event,tlv,mem,sock
-#
+# See https://github.com/open5gs/open5gs/blob/main/configs/open5gs/mme.yaml.in
+
logger:
level: info
-#
-# <S1AP Server>>
-#
-# o S1AP Server(all address available)
-# mme:
-# s1ap:
-#
-# o S1AP Server(0.0.0.0:36412)
-# mme:
-# s1ap:
-# addr: 0.0.0.0
-#
-# o S1AP Server(127.0.0.2:36412, [::1]:36412)
-# mme:
-# s1ap:
-# - addr: 127.0.0.2
-# - addr: ::1
-#
-# o S1AP Server(different port)
-# mme:
-# s1ap:
-# - addr: 127.0.0.2
-# port: 36413
-#
-# o S1AP Server(address available in `eth0` interface)
-# mme:
-# s1ap:
-# dev: eth0
-#
-# o S1AP Option (Default)
-# - sctp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# mme:
-# s1ap:
-# addr: 127.0.0.2
-# option:
-# stcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
-# o S1AP SCTP Option (Default)
-# - spp_hbinterval : 5000 (5secs)
-# - spp_sackdelay : 200 (200ms)
-# - srto_initial : 3000 (3secs)
-# - srto_min : 1000 (1sec)
-# - srto_max : 5000 (5secs)
-# - sinit_num_ostreams : 30
-# - sinit_max_instreams : 65535
-# - sinit_max_attempts : 4
-# - sinit_max_init_timeo : 8000(8secs)
-#
-# mme:
-# s1ap:
-# addr: 127.0.0.2
-# option:
-# sctp:
-# spp_hbinterval : 5000
-# spp_sackdelay : 200
-# srto_initial : 3000
-# srto_min : 1000
-# srto_max : 5000
-# sinit_num_ostreams : 30
-# sinit_max_instreams : 65535
-# sinit_max_attempts : 4
-# sinit_max_init_timeo : 8000
-#
-# <GTP-C Server>>
-#
-# o GTP-C Server(all address available)
-# mme:
-# gtpc:
-#
-# o GTP-C Server(127.0.0.2:2123, [::1]:2123)
-# mme:
-# gtpc:
-# - addr: 127.0.0.2
-# - addr: ::1
-#
-# <SGsAP>
-#
-# o Single MSC/VLR(127.0.0.2)
-# mme:
-# sgsap:
-# addr: 127.0.0.2
-# map:
-# tai:
-# plmn_id:
-# mcc: 001
-# mnc: 01
-# tac: 4130
-# lai:
-# plmn_id:
-# mcc: 001
-# mnc: 01
-# lac: 43690
-# map:
-# tai:
-# plmn_id:
-# mcc: 002
-# mnc: 02
-# tac: 4132
-# lai:
-# plmn_id:
-# mcc: 002
-# mnc: 02
-# lac: 43692
-#
-# o Multiple MSC/VLR
-# mme:
-# sgsap:
-# - addr: 127.0.0.2
-# port: 29119
-# map:
-# tai:
-# plmn_id:
-# mcc: 001
-# mnc: 01
-# tac: 4131
-# lai:
-# plmn_id:
-# mcc: 001
-# mnc: 01
-# lac: 43691
-# map:
-# tai:
-# plmn_id:
-# mcc: 002
-# mnc: 02
-# tac: 4132
-# lai:
-# plmn_id:
-# mcc: 002
-# mnc: 02
-# lac: 43692
-# - addr
-# - 127.0.0.4
-# - fd69:f21d:873c:fa::2
-# map:
-# tai:
-# plmn_id:
-# mcc: 001
-# mnc: 01
-# tac: 4132
-# lai:
-# plmn_id:
-# mcc: 002
-# mnc: 02
-# lac: 43692
-# - name: msc.open5gs.org
-# map:
-# tai:
-# plmn_id:
-# mcc: 001
-# mnc: 01
-# tac: 4133
-# lai:
-# plmn_id:
-# mcc: 002
-# mnc: 02
-# lac: 43693
-#
-# <Metrics Server>
-#
-# o Metrics Server(http://<any address>:9090)
-# mme:
-# metrics:
-# - addr: 0.0.0.0
-# port: 9090
-#
-# <GUMMEI>
-#
-# o Multiple GUMMEI
-# mme:
-# gummei:
-# - plmn_id:
-# mcc: 001
-# mnc: 01
-# mme_gid: 2
-# mme_code: 1
-# - plmn_id:
-# - mcc: 002
-# mnc: 02
-# - mcc: 003
-# mnc: 03
-# mme_gid: [3, 4]
-# mme_code:
-# - 2
-# - 3
-#
-#
-# <TAI>
-#
-# o Multiple TAI
-#
-# When multiple TAIs are configured as shown below,
-# the Served TAI is determined by comparing UserLocationInformation
-# of UplinkNASTransport sent from eNB.
-#
-# For example, if the eNB sends TAC with 30 to the MME,
-# the fourth TAI (TAC: 20, 28, 29-32, 36-38, 40-42, 50, 60, 70, 70)
-# is determined as the Served TAI. The result is transmitted to the eNB
-# as a Tracking Area identity List in Registration Accept.
-#
-# mme:
-# tai:
-# - plmn_id:
-# mcc: 001
-# mnc: 01
-# tac: [1, 3, 5]
-# tai:
-# - plmn_id:
-# mcc: 002
-# mnc: 02
-# tac: [6-10, 15-18]
-# tai:
-# - plmn_id:
-# mcc: 003
-# mnc: 03
-# tac: 20
-# - plmn_id:
-# mcc: 004
-# mnc: 04
-# tac: 21
-# tai:
-# - plmn_id:
-# mcc: 005
-# mnc: 05
-# tac: [22, 28]
-# - plmn_id:
-# mcc: 006
-# mnc: 06
-# tac: [30-32, 34, 36-38, 40-42, 44, 46, 48]
-# - plmn_id:
-# mcc: 007
-# mnc: 07
-# tac: 50
-# - plmn_id:
-# mcc: 008
-# mnc: 08
-# tac: 60
-# - plmn_id:
-# mcc: 009
-# mnc: 09
-# tac: [70, 80]
-#
-#
-# <Access Control>
-#
-# If access_control is not specified, then all networks are allowed
-# If access_control is defined,
-# no other networks are allowed other than matching plmn_id.
-#
-# default_reject_cause may be used to overwrite the default error cause #11
-# for non matching plmn_id
-#
-# for matching plmn_id with reject_cause defined,
-# the MME rejects access with the reject_cause error cause
-#
-# for matching plmn_id without reject_cause defined,
-# the MME accepts the PLMN traffic
-#
-# o The example below only accepts 002/02 and 999/70 PLMNs.
-# 001/01 is rejected with cause 15,
-# and the rest of the PLMNs are rejected with default cause 13.
-#
-# mme:
-# access_control:
-# - default_reject_cause: 13
-# - plmn_id:
-# reject_cause: 15
-# mcc: 001
-# mnc: 01
-# - plmn_id:
-# mcc: 002
-# mnc: 02
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-#
-#
-# <Network Name>
-# mme:
-# network_name:
-# full: Open5GS
-# short: Next
-#
-# <MME Name>
-# mme:
-# mme_name: open5gs-mme0
-#
-# <Relative Capacity> - Default(255)
-# mme:
-# relative_capacity: 100
-#
mme:
freeDiameter: /data/freediameter.conf
s1ap:
@@ -345,172 +30,16 @@
full: Open5GS
mme_name: open5gs-mme0
-#
-# <GTP-C Client>
-#
-# o Specify SGW addresses the GTP-C must connect to
-#
-# o One SGW is defined.
-# If prefer_ipv4 is not true, [fd69:f21d:873c:fa::2] is selected.
-# sgwc:
-# gtpc:
-# addr:
-# - 127.0.0.3
-# - fd69:f21d:873c:fa::2
-#
-# o Two SGW are defined. MME selects SGW with round-robin manner per UE
-# sgwc:
-# gtpc:
-# - addr: 127.0.0.3
-# - addr: fd69:f21d:873c:fa::2
-#
-# o Three SGW are defined. MME selects SGW with round-robin manner per UE
-# sgwc:
-# gtpc:
-# - addr
-# - 127.0.0.3
-# - fd69:f21d:873c:fa::2
-# - addr
-# - 127.0.0.22
-# - fd69:f21d:873c:fa::12
-# - name: sgw3.open5gs.org
-#
-# <SGW Selection Mode>
-#
-# o Round-Robin
-# sgwc:
-# gtpc:
-# addr: 127.0.0.3
-# addr: 127.0.2.2
-# addr: 127.0.4.2
-#
-# o SGW selection by eNodeB TAC
-# (either single TAC or multiple TACs, DECIMAL representation)
-#
-# sgwc:
-# gtpc:
-# - addr: 127.0.0.3
-# tac: 26000
-# - addr: 127.0.2.2
-# tac: [25000, 27000, 28000]
-#
-# o SGW selection by e_cell_id(28bit)
-# (either single or multiple e_cell_id, HEX representation)
-#
-# sgwc:
-# gtpc:
-# - addr: 127.0.0.3
-# e_cell_id: abcde01
-# - addr: 127.0.2.2
-# e_cell_id: [12345, a9413, 98765]
-#
sgwc:
gtpc:
- addr: 172.18.3.202
-#
-# smf:
-#
-# <GTP-C Client>
-#
-# o By default, the SMF uses the first SMF node.
-# - To use a different APN for each SMF, specify gtpc.apn as the APN name.
-# - If the HSS uses WebUI to set the SMF IP for each UE,
-# you can use a specific SMF node for each UE.
-# (Default values are used, so no configuration is required)
-#
-# o Two SMF are defined. 127.0.0.4:2123 is used.
-# [fd69:f21d:873c:fa::3]:2123 is ignored.
-# smf:
-# gtpc:
-# - addr: 127.0.0.4
-# - addr: fd69:f21d:873c:fa::3
-#
-# o One SMF is defined. if prefer_ipv4 is not true,
-# [fd69:f21d:873c:fa::3] is selected.
-# smf:
-# gtpc:
-# - addr:
-# - 127.0.0.4
-# - fd69:f21d:873c:fa::3
-#
-# o Two SMF are defined with a different APN.
-# - Note that if SMF IP for UE is configured in HSS,
-# the following configurion for this UE is ignored.
-# smf:
-# gtpc:
-# - addr: 127.0.0.4
-# apn: internet
-# - addr: 127.0.0.5
-# apn: volte
-#
-# o If APN is omitted, the default APN uses the first SMF node.
-# smf:
-# gtpc:
-# - addr: 127.0.0.4
-# - addr: 127.0.0.5
-# apn: volte
-#
-# o SMF selection by eNodeB TAC
-# (either single TAC or multiple TACs, DECIMAL representation)
-#
-# gtpc:
-# - addr: 127.0.0.4
-# tac: 26000
-# - addr: 127.0.2.4
-# tac: [25000, 27000, 28000]
-#
-# o SMF selection by e_cell_id(28bit)
-# (either single or multiple e_cell_id, HEX representation)
-#
-# gtpc:
-# - addr: 127.0.0.4
-# e_cell_id: abcde01
-# - addr: 127.0.2.4
-# e_cell_id: [12345, a9413, 98765]
smf:
gtpc:
- addr:
- 172.18.3.201
- ::1
-
-# <GTP-C Client>
-#
-# o Specify SGSN addresses the GTP-C must connect to
-#
-# o One SGSN is defined.
-# If prefer_ipv4 is not true, [fd69:f21d:873c:fa::2] is selected.
-# sgsn:
-# - gtpc:
-# addr:
-# - 127.0.0.3
-# - fd69:f21d:873c:fa::2
-# routes:
-# - rai: XYZ
-# ci: XYZ
-#
-# o Three SGW are defined. MME selects SGW with round-robin manner per UE
-# sgsn:
-# - gtpc:
-# addr:
-# - 127.0.0.3
-# - fd69:f21d:873c:fa::2
-# routes:
-# - rai: XYZ
-# ci: XYZ
-# - gtpc:
-# addr
-# - 127.0.0.22
-# - fd69:f21d:873c:fa::12
-# routes:
-# - rai: XYZ
-# ci: XYZ
-# - name: sgsn3.open5gs.org
-# routes:
-# - rai: XYZ
-# ci: XYZ
-#
sgsn:
- gtpc:
addr:
@@ -526,63 +55,10 @@
rac: 187
ci: 1223
-#
-# o Disable use of IPv4 addresses (only IPv6)
-# parameter:
-# no_ipv4: true
-#
-# o Disable use of IPv6 addresses (only IPv4)
-# parameter:
-# no_ipv6: true
-#
-# o Prefer IPv4 instead of IPv6 for estabishing new GTP connections.
-# parameter:
-# prefer_ipv4: true
-#
parameter:
-#
-# o Maximum Number of UE
-# max:
-# ue: 1024
-#
-# o Maximum Number of Peer(S1AP/NGAP, DIAMETER, GTP, PFCP or SBI)
-# max:
-# peer: 64
-#
max:
-#
-# usrsctp:
-# udp_port : 9899
-#
usrsctp:
-#
-# o Message Wait Duration (Default : 10,000 ms = 10 seconds)
-# (Default values are used, so no configuration is required)
-#
-# o Message Wait Duration (3000 ms)
-# time:
-# message:
-# duration: 3000
-#
-# o Handover Wait Duration (Default : 300 ms)
-# Time to wait for MME to send UEContextReleaseCommand
-# to the source eNB after receiving HandoverNotify
-# (Default values are used, so no configuration is required)
-#
-# o Handover Wait Duration (500ms)
-# time:
-# handover:
-# duration: 500
-#
-# o Timers of EPS mobility/session management
-# time:
-# t3402:
-# value: 720 # 12 minutes * 60 = 720 seconds
-# t3412:
-# value: 3240 # 54 minutes * 60 = 3240 seconds
-# t3423:
-# value: 720 # 12 minutes * 60 = 720 seconds
time:
diff --git a/ttcn3-pgw-test/open5gs-nrf.yaml b/ttcn3-pgw-test/open5gs-nrf.yaml
index a7b615f..b37ec0d 100644
--- a/ttcn3-pgw-test/open5gs-nrf.yaml
+++ b/ttcn3-pgw-test/open5gs-nrf.yaml
@@ -1,68 +1,10 @@
+# See https://github.com/open5gs/open5gs/blob/main/configs/open5gs/nrf.yaml.in
+
db_uri: mongodb://localhost/open5gs
-#
-# logger:
-#
-# o Set OGS_LOG_INFO to all domain level
-# - If `level` is omitted, the default level is OGS_LOG_INFO)
-# - If `domain` is omitted, the all domain level is set from 'level'
-# (Default values are used, so no configuration is required)
-#
-# o Set OGS_LOG_ERROR to all domain level
-# - `level` can be set with none, fatal, error, warn, info, debug, trace
-# logger:
-# level: error
-#
-# o Set OGS_LOG_DEBUG to mme/emm domain level
-# logger:
-# level: debug
-# domain: mme,emm
-#
-# o Set OGS_LOG_TRACE to all domain level
-# logger:
-# level: trace
-# domain: core,sbi,ausf,event,tlv,mem,sock
-#
logger:
level: info
-#
-# o TLS enable/disable
-# sbi:
-# server|client:
-# no_tls: false|true
-# - false: (Default) Use TLS
-# - true: TLS disabled
-#
-# o Verification enable/disable
-# sbi:
-# server|client:
-# no_verify: false|true
-# - false: (Default) Verify the PEER
-# - true: Skip the verification step
-#
-# o Server-side does not use TLS
-# sbi:
-# server:
-# no_tls: true
-#
-# o Client-side skips the verification step
-# sbi:
-# client:
-# no_verify: true
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-#
-# o Use the specified certificate while verifying the client
-# sbi:
-# server
-# cacert: /etc/open5gs/tls/ca.crt
-#
-# o Use the specified certificate while verifying the server
-# sbi:
-# client
-# cacert: /etc/open5gs/tls/ca.crt
-#
sbi:
server:
no_tls: true
@@ -75,266 +17,20 @@
key: /etc/open5gs/tls/nrf.key
cert: /etc/open5gs/tls/nrf.crt
-#
-# <SBI Server>
-#
-# o SBI Server(http://<all address available>:80)
-# sbi:
-# server:
-# no_tls: true
-# nrf:
-# sbi:
-#
-# o SBI Server(http://<any address>:7777)
-# sbi:
-# server:
-# no_tls: true
-# nrf:
-# sbi:
-# - addr:
-# - 0.0.0.0
-# - ::0
-# port: 7777
-#
-# o SBI Server(https://<all address available>:443)
-# sbi:
-# server:
-# key: /etc/open5gs/tls/nrf.key
-# cert: /etc/open5gs/tls/nrf.crt
-# nrf:
-# sbi:
-#
-# o SBI Server(https://127.0.0.10:443, https://[::1]:443) without verification
-# sbi:
-# server:
-# no_verify: true
-# key: /etc/open5gs/tls/nrf.key
-# cert: /etc/open5gs/tls/nrf.crt
-# nrf:
-# sbi:
-# - addr: 127.0.0.10
-# - addr: ::1
-#
-# o SBI Server(https://nrf.open5gs.org:443)
-# Use the specified certificate while verifying the client
-#
-# sbi:
-# server:
-# cacert: /etc/open5gs/tls/ca.crt
-# key: /etc/open5gs/tls/nrf.key
-# cert: /etc/open5gs/tls/nrf.crt
-# nrf:
-# sbi:
-# - name: nrf.open5gs.org
-#
-# o SBI Server(http://127.0.0.10:7777)
-# sbi:
-# server:
-# no_tls: true
-# nrf:
-# sbi:
-# - addr: 127.0.0.10
-# port: 7777
-#
-# o SBI Server(http://<eth0 IP address>:80)
-# sbi:
-# server:
-# no_tls: true
-# nrf:
-# sbi:
-# - dev: eth0
-#
-# o Provide custom SBI address to be advertised to NRF
-# sbi:
-# server:
-# no_tls: true
-# nrf:
-# sbi:
-# - dev: eth0
-# advertise: open5gs-nrf.svc.local
-#
-# o Another example of advertising on NRF
-# sbi:
-# server:
-# no_tls: true
-# nrf:
-# sbi:
-# - addr: localhost
-# advertise:
-# - 127.0.0.99
-# - ::1
-#
-# o SBI Option (Default)
-# - tcp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# sbi:
-# server:
-# no_tls: true
-# nrf:
-# sbi:
-# addr: 127.0.0.10
-# option:
-# tcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
-# <NF Service>
-#
-# o NF Service Name(Default : all NF services available)
-# nrf:
-# service_name:
-#
-# o NF Service Name(Only some NF services are available)
-# nrf:
-# service_name:
-# - nnrf-nfm
-# - nnrf-disc
-#
nrf:
sbi:
addr:
- 172.18.18.10
port: 7777
-#
-# <SBI Client>>
-#
-# o SBI Client(http://127.0.1.10:7777)
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr: 127.0.1.10
-# port: 7777
-#
-# o SBI Client(https://127.0.1.10:443, https://[::1]:443) without verification
-# sbi:
-# client:
-# no_verify: true
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# scp:
-# sbi:
-# - addr: 127.0.1.10
-# - addr: ::1
-#
-# o SBI Client(https://scp.open5gs.org:443)
-# Use the specified certificate while verifying the server
-#
-# sbi:
-# client:
-# cacert: /etc/open5gs/tls/ca.crt
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# scp:
-# sbi:
-# - name: scp.open5gs.org
-#
-# o SBI Client(http://[fd69:f21d:873c:fb::1]:80)
-# If prefer_ipv4 is true, http://127.0.1.10:80 is selected.
-#
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr:
-# - 127.0.1.10
-# - fd69:f21d:873c:fb::1
-#
-# o SBI Option (Default)
-# - tcp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr: 127.0.1.10
-# option:
-# tcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
-#
scp:
sbi:
- addr: 127.0.1.10
port: 7777
-#
-# o Disable use of IPv4 addresses (only IPv6)
-# parameter:
-# no_ipv4: true
-#
-# o Disable use of IPv6 addresses (only IPv4)
-# parameter:
-# no_ipv6: true
-#
-# o Prefer IPv4 instead of IPv6 for estabishing new GTP connections.
-# parameter:
-# prefer_ipv4: true
-#
parameter:
-#
-# o Maximum Number of UE
-# max:
-# ue: 1024
-#
-# o Maximum Number of Peer(S1AP/NGAP, DIAMETER, GTP, PFCP or SBI)
-# max:
-# peer: 64
-#
max:
-#
-#
-# o NF Instance Heartbeat (Default : 10 seconds)
-# (Default values are used, so no configuration is required)
-#
-# o NF Instance Heartbeat (Disabled)
-# time:
-# nf_instance:
-# heartbeat: 0
-#
-# o NF Instance Heartbeat (5 seconds)
-# time:
-# nf_instance:
-# heartbeat: 5
-#
-# o NF Instance Validity (Default : 3600 seconds = 1 hour)
-# (Default values are used, so no configuration is required)
-#
-# o NF Instance Validity (10 seconds)
-# time:
-# nf_instance:
-# validity: 10
-#
-# o Subscription Validity (Default : 86400 seconds = 1 day)
-# (Default values are used, so no configuration is required)
-#
-# o Subscription Validity (Disabled)
-# time:
-# subscription:
-# validity: 0
-#
-# o Subscription Validity (3600 seconds = 1 hour)
-# time:
-# subscription:
-# validity: 3600
-#
-# o Message Wait Duration (Default : 10,000 ms = 10 seconds)
-# (Default values are used, so no configuration is required)
-#
-# o Message Wait Duration (3000 ms)
-# time:
-# message:
-# duration: 3000
time:
diff --git a/ttcn3-pgw-test/open5gs-smf.yaml b/ttcn3-pgw-test/open5gs-smf.yaml
index f75a6e6..622618b 100644
--- a/ttcn3-pgw-test/open5gs-smf.yaml
+++ b/ttcn3-pgw-test/open5gs-smf.yaml
@@ -1,63 +1,8 @@
-#
-# o Set OGS_LOG_INFO to all domain level
-# - If `level` is omitted, the default level is OGS_LOG_INFO)
-# - If `domain` is omitted, the all domain level is set from 'level'
-# (Default values are used, so no configuration is required)
-#
-# o Set OGS_LOG_ERROR to all domain level
-# - `level` can be set with none, fatal, error, warn, info, debug, trace
-# logger:
-# level: error
-#
-# o Set OGS_LOG_DEBUG to mme/emm domain level
-# logger:
-# level: debug
-# domain: mme,emm
-#
-# o Set OGS_LOG_TRACE to all domain level
-# logger:
-# level: trace
-# domain: core,sbi,ausf,event,tlv,mem,sock
-#
+# See https://github.com/open5gs/open5gs/blob/main/configs/open5gs/smf.yaml.in
+
logger:
level: info
-#
-# o TLS enable/disable
-# sbi:
-# server|client:
-# no_tls: false|true
-# - false: (Default) Use TLS
-# - true: TLS disabled
-#
-# o Verification enable/disable
-# sbi:
-# server|client:
-# no_verify: false|true
-# - false: (Default) Verify the PEER
-# - true: Skip the verification step
-#
-# o Server-side does not use TLS
-# sbi:
-# server:
-# no_tls: true
-#
-# o Client-side skips the verification step
-# sbi:
-# client:
-# no_verify: true
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-#
-# o Use the specified certificate while verifying the client
-# sbi:
-# server
-# cacert: /etc/open5gs/tls/ca.crt
-#
-# o Use the specified certificate while verifying the server
-# sbi:
-# client
-# cacert: /etc/open5gs/tls/ca.crt
-#
+
sbi:
server:
no_tls: true
@@ -70,525 +15,6 @@
key: /etc/open5gs/tls/smf.key
cert: /etc/open5gs/tls/smf.crt
-#
-# <SBI Server>
-#
-# o SBI Server(http://<all address available>:80)
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-#
-# o SBI Server(http://<any address>:7777)
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr:
-# - 0.0.0.0
-# - ::0
-# port: 7777
-#
-# o SBI Server(https://<all address available>:443)
-# sbi:
-# server:
-# key: /etc/open5gs/tls/smf.key
-# cert: /etc/open5gs/tls/smf.crt
-# smf:
-# sbi:
-#
-# o SBI Server(https://127.0.0.4:443, https://[::1]:443) without verification
-# sbi:
-# server:
-# no_verify: true
-# key: /etc/open5gs/tls/smf.key
-# cert: /etc/open5gs/tls/smf.crt
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# - addr: ::1
-#
-# o SBI Server(https://smf.open5gs.org:443)
-# Use the specified certificate while verifying the client
-#
-# sbi:
-# server:
-# cacert: /etc/open5gs/tls/ca.crt
-# key: /etc/open5gs/tls/smf.key
-# cert: /etc/open5gs/tls/smf.crt
-# smf:
-# sbi:
-# - name: smf.open5gs.org
-#
-# o SBI Server(http://127.0.0.4:7777)
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-#
-# o SBI Server(http://<eth0 IP address>:80)
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - dev: eth0
-#
-# o Provide custom SBI address to be advertised to NRF
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - dev: eth0
-# advertise: open5gs-smf.svc.local
-#
-# o Another example of advertising on NRF
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: localhost
-# advertise:
-# - 127.0.0.99
-# - ::1
-#
-# o SBI Option (Default)
-# - tcp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# addr: 127.0.0.4
-# option:
-# tcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
-#
-# <NF Service>
-#
-# o NF Service Name(Default : all NF services available)
-# smf:
-# service_name:
-#
-# o NF Service Name(Only some NF services are available)
-# smf:
-# service_name:
-# - nsmf-pdusession
-#
-# <NF Discovery Query Parameter>
-#
-# o (Default) If you do not set Query Parameter as shown below,
-#
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-#
-# - 'service-names' is included.
-#
-# o Service-Names are not included
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-# discovery:
-# option:
-# no_service_names: false
-#
-# o To remove 'service-names' from URI query parameters in NS Discovery
-# no_service_names: true
-#
-# * For Indirect Communication with Delegated Discovery,
-# 'service-names' is always included in the URI query parameter.
-# * That is, 'no_service_names' has no effect.
-#
-# <For Indirect Communication with Delegated Discovery>
-#
-# o (Default) If you do not set Delegated Discovery as shown below,
-#
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-#
-# - Use SCP if SCP available. Otherwise NRF is used.
-# => App fails if both NRF and SCP are unavailable.
-#
-# sbi:
-# server:
-# no_tls: true
-# smf:
-# sbi:
-# - addr: 127.0.0.4
-# port: 7777
-# discovery:
-# delegated: auto
-#
-# o To use SCP always => App fails if no SCP available.
-# delegated: yes
-#
-# o Don't use SCP server => App fails if no NRF available.
-# delegated: no
-#
-# <PFCP Server>
-#
-# o PFCP Server(127.0.0.4:8805, ::1:8805)
-# smf:
-# pfcp:
-# - addr: 127.0.0.4
-# - addr: ::1
-#
-# o PFCP-U Server(127.0.0.1:2152, [::1]:2152)
-# smf:
-# pfcp:
-# name: localhost
-#
-# o PFCP Option (Default)
-# - so_bindtodevice : NULL
-#
-# smf:
-# pfcp:
-# addr: 127.0.0.4
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <GTP-C Server>
-#
-# o GTP-C Server(127.0.0.4:2123, [fd69:f21d:873c:fa::3]:2123)
-# smf:
-# gtpc:
-# addr:
-# - 127.0.0.4
-# - fd69:f21d:873c:fa::3
-#
-# o On SMF, Same configuration
-# (127.0.0.4:2123, [fd69:f21d:873c:fa::3]:2123).
-# smf:
-# gtpc:
-# - addr: 127.0.0.4
-# - addr: fd69:f21d:873c:fa::3
-#
-# o GTP-C Option (Default)
-# - so_bindtodevice : NULL
-#
-# smf:
-# gtpc:
-# addr: 127.0.0.4
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <GTP-U Server>>
-#
-# o GTP-U Server(127.0.0.4:2152, [::1]:2152)
-# smf:
-# gtpu:
-# - addr: 127.0.0.4
-# - addr: ::1
-#
-# o GTP-U Server(127.0.0.1:2152, [::1]:2152)
-# smf:
-# gtpu:
-# name: localhost
-#
-# o GTP-U Option (Default)
-# - so_bindtodevice : NULL
-#
-# smf:
-# gtpu:
-# addr: 127.0.0.4
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <Metrics Server>
-#
-# o Metrics Server(http://<any address>:9090)
-# smf:
-# metrics:
-# - addr: 0.0.0.0
-# port: 9090
-#
-# <Subnet for UE Pool>
-#
-# o IPv4 Pool
-# smf:
-# subnet:
-# addr: 10.45.0.1/16
-#
-# o IPv4/IPv6 Pool
-# smf:
-# subnet:
-# - addr: 10.45.0.1/16
-# - addr: 2001:db8:cafe::1/48
-#
-#
-# o Specific DNN/APN(e.g 'ims') uses 10.46.0.1/16, 2001:db8:babe::1/48
-# ; If the UE has unknown DNN/APN(not internet/ims), SMF/UPF will crash.
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 2001:db8:cafe::1/48
-# dnn: internet
-# - addr: 10.46.0.1/16
-# dnn: ims
-# - addr: 2001:db8:babe::1/48
-# dnn: ims
-#
-# o Specific DNN/APN with the FALLBACK SUBNET(10.47.0.1/16)
-# ; Note that put the FALLBACK SUBNET last to avoid SMF/UPF crash.
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 10.46.0.1/16
-# dnn: ims
-# - addr: 10.50.0.1/16 ## FALLBACK SUBNET
-#
-# o Pool Range Sample
-# smf:
-# subnet:
-# - addr: 10.45.0.1/24
-# range: 10.45.0.100-10.45.0.200
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/24
-# range:
-# - 10.45.0.5-10.45.0.50
-# - 10.45.0.100-
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/24
-# range:
-# - -10.45.0.200
-# - 10.45.0.210-10.45.0.220
-#
-# smf:
-# subnet:
-# - addr: 10.45.0.1/16
-# range:
-# - 10.45.0.100-10.45.0.200
-# - 10.45.1.100-10.45.1.200
-# - addr: 2001:db8:cafe::1/48
-# range:
-# - 2001:db8:cafe:a0::0-2001:db8:cafe:b0::0
-# - 2001:db8:cafe:c0::0-2001:db8:cafe:d0::0
-#
-# <Domain Name Server>
-#
-# o Primary/Secondary can be configured. Others are ignored.
-#
-# smf:
-# dns:
-# - 8.8.8.8
-# - 8.8.4.4
-# - 2001:4860:4860::8888
-# - 2001:4860:4860::8844
-#
-# <MTU Size>
-#
-# o Provisioning a limit on the size of the packets sent by the MS
-# to avoid packet fragmentation in the backbone network
-# between the MS and the GGSN/PGW and/or across the (S)Gi reference point)
-# when some of the backbone links does not support
-# packets larger then 1500 octets
-#
-# <P-CSCF>
-#
-# o Proxy Call Session Control Function
-#
-# smf:
-# p-cscf:
-# - 127.0.0.1
-# - ::1
-#
-# <CTF>
-#
-# o Gy interface parameters towards OCS.
-# o enabled:
-# o auto: Default. Use Gy only if OCS available among Diameter peers
-# o yes: Use Gy always;
-# reject subscribers if no OCS available among Diameter peers
-# o no: Don't use Gy interface if there is an OCS available
-#
-# smf:
-# ctf:
-# enabled: auto|yes|no
-#
-#
-# <SMF Selection - 5G Core only>
-# 1. SMF sends SmfInfo(S-NSSAI, DNN, TAI) to the NRF
-# 2. NRF responds to AMF with SmfInfo during NF-Discovery.
-# 3. AMF selects SMF based on S-NSSAI, DNN and TAI in SmfInfo.
-#
-# Note that if there is no SmfInfo, any AMF can select this SMF.
-#
-# o S-NSSAI[SST:1] and DNN[internet] - At least 1 DNN is required in S-NSSAI
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# dnn:
-# - internet
-#
-# o S-NSSAI[SST:1 SD:009000] and DNN[internet or ims]
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# sd: 009000
-# dnn:
-# - internet
-# - ims
-#
-# o S-NSSAI[SST:1] and DNN[internet] and TAI[PLMN-ID:99970 TAC:1]
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac: 1
-#
-# o If any of conditions below are met:
-# - S-NSSAI[SST:1] and DNN[internet] and TAI[PLMN-ID:99970 TAC:1-9]
-# - S-NSSAI[SST:2 SD:000080] and DNN[internet or ims]
-# - S-NSSAI[SST:4] and DNN[internet] and TAI[PLMN-ID:99970 TAC:10-20,30-40]
-#
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# range:
-# - 1-9
-# - s_nssai:
-# - sst: 2
-# sd: 000080
-# dnn:
-# - internet
-# - ims
-# - s_nssai:
-# - sst: 4
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# range:
-# - 10-20
-# - 30-40
-#
-# o Complex Example
-# smf:
-# info:
-# - s_nssai:
-# - sst: 1
-# dnn:
-# - internet
-# - sst: 1
-# sd: 000080
-# dnn:
-# - internet
-# - ims
-# - sst: 1
-# sd: 009000
-# dnn:
-# [internet, ims]
-# - sst: 2
-# dnn:
-# - internet
-# - sst: 3
-# sd: 123456
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac: [1, 2, 3]
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac: 4
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac:
-# - 5
-# - 6
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# range:
-# - 100-200
-# - 300-400
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# range:
-# - 500-600
-# - 700-800
-# - 900-1000
-# - s_nssai:
-# - sst: 4
-# dnn:
-# - internet
-# tai:
-# - plmn_id:
-# mcc: 999
-# mnc: 70
-# tac: 99
-#
-# <Security Indication - 5G Core only>
-#
-# According to 3GPP TS38.413 Section 9.3.1.27,
-# Security Indication IE may be instructed to 5G gNB.
-#
-# If you set the security_indication in smf.yaml,
-# this information is delivered using PDU Session Resource Request Transfer IE
-#
-# smf:
-# security_indication:
-# integrity_protection_indication: required|preferred|not-needed
-# confidentiality_protection_indication: required|preferred|not-needed
-# maximum_integrity_protected_data_rate_uplink: bitrate64kbs|maximum-UE-rate
-# maximum_integrity_protected_data_rate_downlink: bitrate64kbs|maximum-UE-rate
-#
smf:
sbi:
- addr: 172.18.18.4
@@ -617,262 +43,22 @@
enabled: auto
freeDiameter: /data/freeDiameter-smf.conf
-#
-# <SBI Client>>
-#
-# o SBI Client(http://127.0.1.10:7777)
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr: 127.0.1.10
-# port: 7777
-#
-# o SBI Client(https://127.0.1.10:443, https://[::1]:443) without verification
-# sbi:
-# client:
-# no_verify: true
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# scp:
-# sbi:
-# - addr: 127.0.1.10
-# - addr: ::1
-#
-# o SBI Client(https://scp.open5gs.org:443)
-# Use the specified certificate while verifying the server
-#
-# sbi:
-# client:
-# cacert: /etc/open5gs/tls/ca.crt
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# scp:
-# sbi:
-# - name: scp.open5gs.org
-#
-# o SBI Client(http://[fd69:f21d:873c:fb::1]:80)
-# If prefer_ipv4 is true, http://127.0.1.10:80 is selected.
-#
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr:
-# - 127.0.1.10
-# - fd69:f21d:873c:fb::1
-#
-# o SBI Option (Default)
-# - tcp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# sbi:
-# client:
-# no_tls: true
-# scp:
-# sbi:
-# addr: 127.0.1.10
-# option:
-# tcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
-#
scp:
sbi:
- addr: 127.0.1.10
port: 7777
-
-#
-# <SBI Client>>
-#
-# o SBI Client(http://127.0.0.10:7777)
-# sbi:
-# client:
-# no_tls: true
-# nrf:
-# sbi:
-# addr: 127.0.0.10
-# port: 7777
-#
-# o SBI Client(https://127.0.0.10:443, https://[::1]:443) without verification
-# sbi:
-# client:
-# no_verify: true
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# nrf:
-# sbi:
-# - addr: 127.0.0.10
-# - addr: ::1
-#
-# o SBI Client(https://nrf.open5gs.org:443)
-# Use the specified certificate while verifying the server
-#
-# sbi:
-# client:
-# cacert: /etc/open5gs/tls/ca.crt
-# key: /etc/open5gs/tls/amf.key
-# cert: /etc/open5gs/tls/amf.crt
-# nrf:
-# sbi:
-# - name: nrf.open5gs.org
-#
-# o SBI Client(http://[fd69:f21d:873c:fa::1]:80)
-# If prefer_ipv4 is true, http://127.0.0.10:80 is selected.
-#
-# sbi:
-# addr:
-# - 127.0.0.10
-# - fd69:f21d:873c:fa::1
-#
-# o SBI Option (Default)
-# - tcp_nodelay : true
-# - so_linger.l_onoff : false
-#
-# sbi:
-# client:
-# no_tls: true
-# nrf:
-# sbi:
-# addr: 127.0.0.10
-# option:
-# tcp_nodelay: false
-# so_linger:
-# l_onoff: true
-# l_linger: 10
-#
nrf:
sbi:
- addr:
- 172.18.18.10
port: 7777
-#
-# <PFCP Client>>
-#
-# o PFCP Client(127.0.0.7:8805)
-# upf:
-# pfcp:
-# addr: 127.0.0.7
-#
-# <UPF Selection>
-#
-# o Round-Robin
-# (note that round robin can be disabled for a particular node
-# by setting flag 'rr' to 0)
-#
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# - addr: 127.0.0.12
-# rr: 0
-# - addr: 127.0.0.19
-#
-# o UPF selection by eNodeB TAC
-# (either single TAC or multiple TACs, DECIMAL representation)
-#
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# tac: 1
-# - addr: 127.0.0.12
-# tac: [3,5,8]
-#
-# o UPF selection by UE's DNN/APN (either single DNN/APN or multiple DNNs/APNs)
-#
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# dnn: ims
-# - addr: 127.0.0.12
-# dnn: [internet, web]
-#
-# o UPF selection by CellID(e_cell_id: 28bit, nr_cell_id: 36bit)
-# (either single enb_id or multiple enb_ids, HEX representation)
-#
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# e_cell_id: 463
-# - addr: 127.0.0.12
-# nr_cell_id: [123456789, 9413]
-#
upf:
pfcp:
- addr: 172.18.18.7
-#
-# o Disable use of IPv4 addresses (only IPv6)
-# parameter:
-# no_ipv4: true
-#
-# o Disable use of IPv6 addresses (only IPv4)
-# parameter:
-# no_ipv6: true
-#
-# o Prefer IPv4 instead of IPv6 for estabishing new GTP connections.
-# parameter:
-# prefer_ipv4: true
-#
-# o Disable selection of UPF PFCP in Round-Robin manner
-# parameter:
-# no_pfcp_rr_select: true
-#
-# o Legacy support for pre-release LTE 11 devices
-# - Omits adding local address in packet filters for compatibility
-# parameter:
-# no_ipv4v6_local_addr_in_packet_filter: true
-#
parameter:
-#
-# o Maximum Number of UE
-# max:
-# ue: 1024
-#
-# o Maximum Number of Peer(S1AP/NGAP, DIAMETER, GTP, PFCP or SBI)
-# max:
-# peer: 64
-#
-# o Maximum Number of GTP peer nodes per SGWC/SMF
-# max:
-# gtp_peer: 64
-#
max:
-#
-# o NF Instance Heartbeat (Default : 0)
-# NFs will not send heart-beat timer in NFProfile
-# NRF will send heart-beat timer in NFProfile
-# (Default values are used, so no configuration is required)
-#
-# o NF Instance Heartbeat (20 seconds)
-# NFs will send heart-beat timer (20 seconds) in NFProfile
-# NRF can change heart-beat timer in NFProfile
-# time:
-# nf_instance:
-# heartbeat: 20
-#
-# o Message Wait Duration (Default : 10,000 ms = 10 seconds)
-# (Default values are used, so no configuration is required)
-#
-# o Message Wait Duration (3000 ms)
-# time:
-# message:
-# duration: 3000
-#
-# o Handover Wait Duration (Default : 300 ms)
-# Time to wait for SMF to send
-# PFCP Session Modification Request(Remove Indirect Tunnel) to the UPF
-# after sending Nsmf_PDUSession_UpdateSMContext Response(hoState:COMPLETED)
-# (Default values are used, so no configuration is required)
-#
-# o Handover Wait Duration (500ms)
-# time:
-# handover:
-# duration: 500
time:
diff --git a/ttcn3-pgw-test/open5gs-upf.yaml b/ttcn3-pgw-test/open5gs-upf.yaml
index 693a1d7..fec9fc7 100644
--- a/ttcn3-pgw-test/open5gs-upf.yaml
+++ b/ttcn3-pgw-test/open5gs-upf.yaml
@@ -1,192 +1,8 @@
-#
-# o Set OGS_LOG_INFO to all domain level
-# - If `level` is omitted, the default level is OGS_LOG_INFO)
-# - If `domain` is omitted, the all domain level is set from 'level'
-# (Default values are used, so no configuration is required)
-#
-# o Set OGS_LOG_ERROR to all domain level
-# - `level` can be set with none, fatal, error, warn, info, debug, trace
-# logger:
-# level: error
-#
-# o Set OGS_LOG_DEBUG to mme/emm domain level
-# logger:
-# level: debug
-# domain: mme,emm
-#
-# o Set OGS_LOG_TRACE to all domain level
-# logger:
-# level: trace
-# domain: core,sbi,ausf,event,tlv,mem,sock
-#
+# See https://github.com/open5gs/open5gs/blob/main/configs/open5gs/upf.yaml.in
+
logger:
level: info
-#
-# <PFCP Server>
-#
-# o PFCP Server(127.0.0.7:8805, ::1:8805)
-# upf:
-# pfcp:
-# - addr: 127.0.0.7
-# - addr: ::1
-#
-# o PFCP-U Server(127.0.0.1:2152, [::1]:2152)
-# upf:
-# pfcp:
-# name: localhost
-#
-# o PFCP Option (Default)
-# - so_bindtodevice : NULL
-#
-# upf:
-# pfcp:
-# addr: 127.0.0.7
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <GTP-U Server>>
-#
-# o GTP-U Server(127.0.0.7:2152, [::1]:2152)
-# upf:
-# gtpu:
-# - addr: 127.0.0.7
-# - addr: ::1
-#
-# o GTP-U Server(127.0.0.1:2152, [::1]:2152)
-# upf:
-# gtpu:
-# name: localhost
-#
-# o User Plane IP Resource information
-# upf:
-# gtpu:
-# - addr:
-# - 127.0.0.7
-# - ::1
-# teid_range_indication: 4
-# teid_range: 10
-# network_instance: internet
-# source_interface: 0
-# - addr: 127.0.10.4
-# teid_range_indication: 4
-# teid_range: 5
-# network_instance: ims
-# source_interface: 1
-#
-# o Provide custom UPF GTP-U address to be advertised inside NGAP messages
-# upf:
-# gtpu:
-# - addr: 10.4.128.21
-# advertise: 172.24.15.30
-#
-# upf:
-# gtpu:
-# - addr: 10.4.128.21
-# advertise:
-# - 127.0.0.1
-# - ::1
-#
-# upf:
-# gtpu:
-# - addr: 10.4.128.21
-# advertise: upf1.5gc.mnc001.mcc001.3gppnetwork.org
-#
-# upf:
-# gtpu:
-# - dev: ens3
-# advertise: upf1.5gc.mnc001.mcc001.3gppnetwork.org
-#
-# o GTP-U Option (Default)
-# - so_bindtodevice : NULL
-#
-# upf:
-# gtpu:
-# addr: 127.0.0.7
-# option:
-# so_bindtodevice: vrf-blue
-#
-# <Subnet for UE network>
-#
-# Note that you need to setup your UE network using TUN device.
-# (ogstun, ogstun2, ogstunX, ..)
-#
-# o IPv4 Pool
-# $ sudo ip addr add 10.45.0.1/16 dev ogstun
-#
-# upf:
-# subnet:
-# addr: 10.45.0.1/16
-#
-# o IPv4/IPv6 Pool
-# $ sudo ip addr add 10.45.0.1/16 dev ogstun
-# $ sudo ip addr add 2001:db8:cafe::1/48 dev ogstun
-#
-# upf:
-# subnet:
-# - addr: 10.45.0.1/16
-# - addr: 2001:db8:cafe::1/48
-#
-#
-# o Specific DNN/APN(e.g 'ims') uses 10.46.0.1/16, 2001:db8:babe::1/48
-# All other APNs use 10.45.0.1/16, 2001:db8:cafe::1/48
-# $ sudo ip addr add 10.45.0.1/16 dev ogstun
-# $ sudo ip addr add 10.46.0.1/16 dev ogstun
-# $ sudo ip addr add 2001:db8:cafe::1/48 dev ogstun
-# $ sudo ip addr add 2001:db8:babe::1/48 dev ogstun
-#
-# ; If the UE has unknown DNN/APN(not internet/ims), SMF/UPF will crash.
-#
-# upf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 2001:db8:cafe::1/48
-# dnn: internet
-# - addr: 10.46.0.1/16
-# dnn: ims
-# - addr: 2001:db8:babe::1/48
-# dnn: ims
-#
-# o Specific DNN/APN with the FALLBACK SUBNET(10.47.0.1/16)
-# ; Note that put the FALLBACK SUBNET last to avoid SMF/UPF crash.
-#
-# upf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 10.46.0.1/16
-# dnn: ims
-# - addr: 10.50.0.1/16 ## FALLBACK SUBNET
-#
-# o Multiple Devices (default: ogstun)
-# $ sudo ip addr add 10.45.0.1/16 dev ogstun
-# $ sudo ip addr add 2001:db8:cafe::1/48 dev ogstun2
-# $ sudo ip addr add 10.46.0.1/16 dev ogstun3
-# $ sudo ip addr add 2001:db8:babe::1/48 dev ogstun3
-#
-# upf:
-# subnet:
-# - addr: 10.45.0.1/16
-# dnn: internet
-# - addr: 2001:db8:cafe::1/48
-# dnn: internet
-# dev: ogstun2
-# - addr: 10.46.0.1/16
-# dnn: ims
-# dev: ogstun3
-# - addr: 2001:db8:babe::1/48
-# dnn: ims
-# dev: ogstun3
-#
-# <Metrics Server>
-#
-# o Metrics Server(http://<any address>:9090)
-# upf:
-# metrics:
-# - addr: 0.0.0.0
-# port: 9090
-#
upf:
pfcp:
- addr: 172.18.18.7
@@ -200,54 +16,12 @@
dnn: internet
dev: ogstun46
-#
-# <PFCP Client>>
-#
-# o PFCP Client(127.0.0.4:8805)
-# smf:
-# pfcp:
-# addr: 127.0.0.4
-#
smf:
pfcp:
addr: 172.18.18.4
-#
-# o Number of output streams per SCTP associations.
-# parameter:
-# sctp_streams: 30
-#
-# o Disable use of IPv4 addresses (only IPv6)
-# parameter:
-# no_ipv4: true
-#
-# o Disable use of IPv6 addresses (only IPv4)
-# parameter:
-# no_ipv6: true
-#
-# o Prefer IPv4 instead of IPv6 for estabishing new GTP connections.
-# parameter:
-# prefer_ipv4: true
-#
parameter:
-#
-# o Maximum Number of UE
-# max:
-# ue: 1024
-#
-# o Maximum Number of Peer(S1AP/NGAP, DIAMETER, GTP, PFCP or SBI)
-# max:
-# peer: 64
-#
max:
-#
-# o Message Wait Duration (Default : 10,000 ms = 10 seconds)
-# (Default values are used, so no configuration is required)
-#
-# o Message Wait Duration (3000 ms)
-# time:
-# message:
-# duration: 3000
time:
--
To view, visit https://gerrit.osmocom.org/c/docker-playground/+/35103?usp=email
To unsubscribe, or for help writing mail filters, visit
https://gerrit.osmocom.org/settings
Gerrit-Project: docker-playground
Gerrit-Branch: master
Gerrit-Change-Id: I67c2a198b9682e15e23a466380e62a976e6236cd
Gerrit-Change-Number: 35103
Gerrit-PatchSet: 1
Gerrit-Owner: osmith <osmith(a)sysmocom.de>
Gerrit-Reviewer: Jenkins Builder
Gerrit-Reviewer: daniel <dwillmann(a)sysmocom.de>
Gerrit-Reviewer: fixeria <vyanitskiy(a)sysmocom.de>
Gerrit-Reviewer: osmith <osmith(a)sysmocom.de>
Gerrit-MessageType: merged