Issue with C139

Hi all, I have been using C123 for a long time with FTDI cable. I recently bought a C139 on which I wanted to run layer1 fw, i check the SW version using #02# and software version is "1.3.29", UART Flag is "0" On going through the mailing list I found these to be sufficient for using osmocom-bb but some how there is a problem on loading. When I use the fwg command ./osmocon -p /dev/ttyUSB0 -m c140 -c ../../target/firmware/board/compal_e86/layer1.highram.bin I get the following got 2 bytes from modem, data looks like: 04 81 .. got 5 bytes from modem, data looks like: 1b f6 02 00 41 ....A got 1 bytes from modem, data looks like: 01 . got 1 bytes from modem, data looks like: 40 @ Received PROMPT1 from phone, responding with CMD read_file(chainloader): file_size=32, hdr_len=4, dnload_len=15341 got 1 bytes from modem, data looks like: 1b . got 1 bytes from modem, data looks like: f6 . got 1 bytes from modem, data looks like: 02 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: 41 A got 1 bytes from modem, data looks like: 02 . got 1 bytes from modem, data looks like: 43 C Received PROMPT2 from phone, starting download handle_write(): 4096 bytes (4096/15341) handle_write(): 4096 bytes (8192/15341) handle_write(): 4096 bytes (12288/15341) handle_write(): 3053 bytes (15341/15341) handle_write(): finished It receives prompt2 and loads the file but doesn't move ahead, the phone does not show layer1 on the screen either. when i use fwg command (add -m c140xor ) ./osmocon -p /dev/ttyUSB0 -m c140xor -c ../../target/firmware/board/compal_e86/layer1.highram.bin I get the fwg: got 1 bytes from modem, data looks like: 04 . got 1 bytes from modem, data looks like: 81 . got 5 bytes from modem, data looks like: 1b f6 02 00 41 ....A got 1 bytes from modem, data looks like: 01 . got 1 bytes from modem, data looks like: 40 @ Received PROMPT1 from phone, responding with CMD read_file(chainloader): file_size=32, hdr_len=4, dnload_len=15341 got 1 bytes from modem, data looks like: 1b . got 1 bytes from modem, data looks like: f6 . got 1 bytes from modem, data looks like: 02 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: 41 A got 1 bytes from modem, data looks like: 02 . got 1 bytes from modem, data looks like: 43 C Received PROMPT2 from phone, starting download handle_write(): 4096 bytes (4096/15341) handle_write(): 4096 bytes (8192/15341) handle_write(): 4096 bytes (12288/15341) handle_write(): 3053 bytes (15341/15341) handle_write(): finished got 1 bytes from modem, data looks like: 1b . got 1 bytes from modem, data looks like: f6 . got 1 bytes from modem, data looks like: 02 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: 41 A got 1 bytes from modem, data looks like: 03 . got 1 bytes from modem, data looks like: 57 W Received MAGIC NACK from phone, you need to have "1003" at 0x803ce0 got 1 bytes from modem, data looks like: 66 f got 1 bytes from modem, data looks like: 74 t got 1 bytes from modem, data looks like: 6d m got 1 bytes from modem, data looks like: 74 t got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 6c l Received FTMTOOL from phone, ramloader has aborted got 1 bytes from modem, data looks like: 65 e got 1 bytes from modem, data looks like: 72 r got 1 bytes from modem, data looks like: 72 r got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 72 r It now move ahead and says the received MAGIC NACK and also that you need to have "1003" at 0x803ce0, this is a documented problem and i believe in compal_e86 binaries must have been taken care of. Any ideas on how can I get around this and load the firmware on my c139 ? I am again usung the same cable FTDI which works perfectly with c123. My setup is native Ubuntu 14.04 , host machine and Intel i5.. (hw does not seem to be the problem) Looking forward to hear from you guys. Thanks in advance. Regards, Ajay merlinsignals.blogspot.in