Hi Andy,
That setup seemed to have worked for me once I rebuilt it again.
But I'm still facing the same error as stated by Amber & Sarosh
The 2nd BTS refuses to take the configuration of "bts 1". I have tried to
run the 2nd BTS on the same machine as well as from a networked machine.
------------------------------------------------------------------------------------------
root@nistws4:/home/nist-ws4# osmobts-trx -c /root/.osmocom/ho_bts1.cfg
((*))
|
/ \ OsmoBTS
Using MAC address of eth0: '40:a8:f0:63:c7:b6'
<0006> scheduler.c:212 Init scheduler for trx=0
<000b> trx_if.c:493 Open transceiver for trx=0
<000b> trx_if.c:504 Waiting for transceiver send clock
There is no such command.
Error occurred during reading below line:
band DCS1800
% Unknown BTS number 1 (num 1)
Failed to parse the config file: '/root/.osmocom/ho_bts1.cfg'
------------------------------------------------------------------------------------------
Configuration file for ho_bts1.cfg is as follows:
------------------------------------------------------------------------------------------
bts 1
band DCS1800
ipa unit-id 1802 0
oml remote-ip 172.30.1.10
rtp bind-ip 172.30.1.10
rtp jitter-buffer 0
paging lifetime 0
gsmtap-sapi bcch
gsmtap-sapi ccch
gsmtap-sapi rach
gsmtap-sapi agch
gsmtap-sapi pch
gsmtap-sapi sdcch
gsmtap-sapi pacch
gsmtap-sapi pdtch
gsmtap-sapi sacch
fn-advance 20
ms-power-loop -60
timing-advance-loop
trx 0
rxgain 0
power 0
------------------------------------------------------------------------------------------
Can you please suggest some alternatives?
Thanks and Regards,
Jijo
On Thu, May 21, 2015 at 12:06 PM, Joe Ge <jijo123789(a)gmail.com> wrote:
Hi Andy,
There are no logs in the location you specified.
Does it need to be activated somehow(debug mode)???
What might be the problem?
Regards,
Jijo
On Wed, May 20, 2015 at 9:29 PM, Andy Avtushenko <
andy.avtushenko(a)gmail.com> wrote:
Hello Jijo
Could you please provide us a osmo-trx logs
located in var/logs/osmo-trx/current
thanks
2015-05-20 4:34 GMT-08:00 Jijo <jijo123789(a)gmail.com>om>:
Hi Alexander,
I'm working on a similar setup as Amber & Sarosh, till about recently I
was
facing the same error as these guys (where the config file was not
parsing
the trx 1 and later sections) when I stumbled upon your response.
Now I've installed the same versions as suggested by you :
osmo_trx: fairwaves/master
libosmocore: master
libosmo-abis: fairwaves/master
libsmpp34: master
osmo_bts: fairwaves/debian
openbsc: fairwaves/master
But somehow my osmobts-trx is not recognizing osmo-trx
--------------------------------------------------------
<0001> oml.c:419 L3=0x94eb07e, VAL=0x94eb0ad, DIF=47
<0001> oml.c:790 ADM state already was Unlocked
<0001> oml.c:790 ADM state already was Unlocked
<0001> oml.c:790 ADM state already was Unlocked
<0001> oml.c:790 ADM state already was Unlocked
<000b> trx_if.c:187 No response from transceiver for trx=0
<000b> trx_if.c:187 No response from transceiver for trx=0
<000b> trx_if.c:187 No response from transceiver for trx=0
<000b> trx_if.c:187 No response from transceiver for trx=0
--------------------------------------------------------
I'm using UmDESK for this setup.
PS- I built osmo-bts with(./configure --enable-trx). I hope that was
correct
for UmDESK
Can you help with this regard?
Thanks and Regards,
Jijo
--
Best regards,
Andy