Hi Andy,That setup seemed to have worked for me once I rebuilt it again.But I'm still facing the same error as stated by Amber & SaroshThe 2nd BTS refuses to take the configuration of "bts 1". I have tried to run the 2nd BTS on the same machine as well as from a networked machine.------------------------------------------------------------------------------------------root@nistws4:/home/nist-ws4# osmobts-trx -c /root/.osmocom/ho_bts1.cfg((*))|/ \ OsmoBTSUsing MAC address of eth0: '40:a8:f0:63:c7:b6'<0006> scheduler.c:212 Init scheduler for trx=0<000b> trx_if.c:493 Open transceiver for trx=0<000b> trx_if.c:504 Waiting for transceiver send clockThere is no such command.Error occurred during reading below line:band DCS1800% Unknown BTS number 1 (num 1)Failed to parse the config file: '/root/.osmocom/ho_bts1.cfg'------------------------------------------------------------------------------------------Configuration file for ho_bts1.cfg is as follows:------------------------------------------------------------------------------------------bts 1band DCS1800ipa unit-id 1802 0oml remote-ip 172.30.1.10rtp bind-ip 172.30.1.10rtp jitter-buffer 0paging lifetime 0gsmtap-sapi bcchgsmtap-sapi ccchgsmtap-sapi rachgsmtap-sapi agchgsmtap-sapi pchgsmtap-sapi sdcchgsmtap-sapi pacchgsmtap-sapi pdtchgsmtap-sapi sacchfn-advance 20ms-power-loop -60timing-advance-looptrx 0rxgain 0power 0------------------------------------------------------------------------------------------Can you please suggest some alternatives?Thanks and Regards,JijoOn Thu, May 21, 2015 at 12:06 PM, Joe Ge <jijo123789@gmail.com> wrote:Hi Andy,There are no logs in the location you specified.Does it need to be activated somehow(debug mode)???What might be the problem?Regards,JijoOn Wed, May 20, 2015 at 9:29 PM, Andy Avtushenko <andy.avtushenko@gmail.com> wrote:Hello JijoCould you please provide us a osmo-trx logslocated in var/logs/osmo-trx/currentthanks2015-05-20 4:34 GMT-08:00 Jijo <jijo123789@gmail.com>:Hi Alexander,
I'm working on a similar setup as Amber & Sarosh, till about recently I was
facing the same error as these guys (where the config file was not parsing
the trx 1 and later sections) when I stumbled upon your response.
Now I've installed the same versions as suggested by you :
osmo_trx: fairwaves/master
libosmocore: master
libosmo-abis: fairwaves/master
libsmpp34: master
osmo_bts: fairwaves/debian
openbsc: fairwaves/master
But somehow my osmobts-trx is not recognizing osmo-trx
--------------------------------------------------------
<0001> oml.c:419 L3=0x94eb07e, VAL=0x94eb0ad, DIF=47
<0001> oml.c:790 ADM state already was Unlocked
<0001> oml.c:790 ADM state already was Unlocked
<0001> oml.c:790 ADM state already was Unlocked
<0001> oml.c:790 ADM state already was Unlocked
<000b> trx_if.c:187 No response from transceiver for trx=0
<000b> trx_if.c:187 No response from transceiver for trx=0
<000b> trx_if.c:187 No response from transceiver for trx=0
<000b> trx_if.c:187 No response from transceiver for trx=0
--------------------------------------------------------
I'm using UmDESK for this setup.
PS- I built osmo-bts with(./configure --enable-trx). I hope that was correct
for UmDESK
Can you help with this regard?
Thanks and Regards,
Jijo
--Best regards,Andy