25 Jul
2014
25 Jul
'14
12:25 p.m.
Hi all
I have built Osmocommbb with testing branch and I want to run Mobile app
allowing me to make a call via my local network.
All goes well in the build but I am unable to register on my own network
while using a genuine network sim.
This is output from my compal_e88/layer1.compalram.bin.
As you can see all looks good with signal levels fairly ok until this point
and then level drops to -138 dbm and there it stays on all chanells.
I have tried this with 3 different sims and all is the same.
Can someone help?
Tom
bat_compal_e88_chg_state=0
L1CTL_RESET_REQ: FULL!SIM Request (7): a0 a4 00 00 02 3f 00
SIM Response (2): 9f 20
SIM Request (5): a0 c0 00 00 20
SIM Response (34): 00 00 02 b7 3f 00 01 00 00 00 00 00 13 b3 05 0a 04 00 83
8a 83 8a 00 03 00 00 02 b7 00 00 02 b7 90 00
SIM Request (7): a0 a4 00 00 02 2f e2
SIM Response (2): 9f 0f
SIM Request (5): a0 c0 00 00 0f
SIM Response (17): 00 00 00 0a 2f e2 04 00 0f 00 ff 01 02 00 00 90 00
SIM Request (5): a0 b0 00 00 0a
SIM Response (12): 98 53 03 11 02 08 22 45 65 f6 90 00
SIM Request (7): a0 a4 00 00 02 7f 20
SIM Response (2): 9f 20
SIM Request (5): a0 c0 00 00 20
SIM Response (34): 00 00 00 00 7f 20 02 00 00 00 00 00 13 b3 00 23 04 00 83
8a 83 8a 00 03 00 00 02 b7 00 00 00 00 90 00
SIM Request (7): a0 a4 00 00 02 6f 07
SIM Response (2): 9f 0f
SIM Request (5): a0 c0 00 00 0f
SIM Response (17): 00 00 00 09 6f 07 04 00 14 00 14 01 02 00 00 90 00
SIM Request (5): a0 b0 00 00 09
SIM Response (11): 08 29 27 10 17 21 89 26 33 90 00
SIM Request (7): a0 a4 00 00 02 6f 7e
SIM Response (2): 9f 0f
SIM Request (5): a0 c0 00 00 0f
SIM Response (17): 00 00 00 0b 6f 7e 04 00 11 00 14 01 02 00 00 90 00
SIM Request (5): a0 b0 00 00 0b
SIM Response (13): ff ff ff ff 72 f2 60 ff fe 00 03 90 00
SIM Request (7): a0 a4 00 00 02 6f 20
SIM Response (2): 9f 0f
SIM Request (5): a0 c0 00 00 0f
SIM Response (17): 00 00 00 09 6f 20 04 00 11 00 44 01 02 00 00 90 00
SIM Request (5): a0 b0 00 00 09
SIM Response (11): ff ff ff ff ff ff ff ff 07 90 00
SIM Request (7): a0 a4 00 00 02 6f 30
SIM Response (2): 9f 0f
SIM Request (5): a0 c0 00 00 0f
SIM Response (17): 00 00 01 2c 6f 30 04 00 11 00 44 01 02 00 00 90 00
SIM Request (5): a0 b0 00 00 2c
SIM Response (46): 32 f4 51 02 f8 01 12 f4 60 12 f4 10 62 f2 20 02 f4 40 22
f2 01 02 f6 10 22 f8 10 72 f0 77 62 f8 10 42 f0 80 32 f8 10 02 f2 50 32 f2
90 00
BAT-ADC: 593 6 0 0 1023 353 327 277
Charger at 51 mV.
PM MEAS: ARFCN=1016, 33 dBm at baseband, -104 dBm at RF
PM MEAS: ARFCN=1017, 33 dBm at baseband, -104 dBm at RF
PM MEAS: ARFCN=1018, 29 dBm at baseband, -108 dBm at RF
PM MEAS: ARFCN=1019, 29 dBm at baseband, -108 dBm at RF
PM MEAS: ARFCN=1020, 28 dBm at baseband, -109 dBm at RF
PM MEAS: ARFCN=1021, 29 dBm at baseband, -108 dBm at RF
PM MEAS: ARFCN=1022, 27 dBm at baseband, -110 dBm at RF
PM MEAS: ARFCN=1023, 39 dBm at baseband, -98 dBm at RF
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=1, flags=0x7)
Starting FCCH RecognitionFB0 (3859:4): TOA= 3792, Power= -88dBm,
Angle=-1361Hz
DSP Error Status: 256
FB1 (3869:8): TOA= 8751, Power= -88dBm, Angle= -36Hz
fn_offset=3867 (fn=3869 + attempt=8 + ntdma = 6)
delay=8 (fn_offset=3867 + 11 - fn=3869 - 1
scheduling next FB/SB detection task with delay 8
=>FB @ FNR 3867 fn_offset=3867 qbits=4820
Synchronize_TDMA
LOST 3711!
DSP Error Status: 256
DSP Error Status: 264
L1CTL_RESET_REQ: FULL!LOST 1893!
L1CTL_FBSB_REQ (arfcn=981, flags=0x7)
Starting FCCH RecognitionLOST 1857!
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=71, flags=0x7)
Starting FCCH RecognitionL1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=993,
flags=0x7)
Starting FCCH RecognitionL1CTL_RESET_REQ: FULL!LOST 1899!
L1CTL_FBSB_REQ (arfcn=979, flags=0x7)
Starting FCCH RecognitionLOST 1851!
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=4, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
BAT-ADC: 590 6 0 0 1023 356 330 277
Charger at 51 mV.
Battery at 4033 mV.
Charging at 0 mA.
Battery capacity is 100%.
Battery range is 3199..3999 mV.
Battery full at 468 LSB .. full at 585 LSB
Charging at 239 LSB (204 mA).
BCICTL2=0x3ff
battery-info.flags=0x00000000
bat_compal_e88_chg_state=0
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=1023, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!LOST 1900!
L1CTL_FBSB_REQ (arfcn=980, flags=0x7)
Starting FCCH RecognitionLOST 1850!
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=78, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=53, flags=0x7)
LOST 1880!
Starting FCCH RecognitionLOST 1870!
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=69, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=94, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=57, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=985, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=970, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=45, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=43, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=33, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=7, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=988, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=971, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=969, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=42, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=40, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=32, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
BAT-ADC: 592 6 0 0 1023 353 327 270
Charger at 51 mV.
Battery at 4047 mV.
Charging at 0 mA.
Battery capacity is 100%.
Battery range is 3199..3999 mV.
Battery full at 468 LSB .. full at 585 LSB
Charging at 239 LSB (204 mA).
BCICTL2=0x3ff
battery-info.flags=0x00000000
bat_compal_e88_chg_state=0
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=85, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=55, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=47, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=28, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=5, flags=0x7)
Starting FCCH RecognitionDSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
DSP Error Status: 8
L1CTL_RESET_REQ: FULL!L1CTL_PM_REQ start=0 end=124
DSP Error Status: 8
PM MEAS: ARFCN=0, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=1, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=2, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=3, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=4, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=5, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=6, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=7, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=8, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=9, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=10, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=11, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=12, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=13, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=14, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=15, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=16, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=17, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=18, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=19, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=20, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=21, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=22, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=23, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=24, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=25, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=26, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=27, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=28, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
PM MEAS: ARFCN=29, 0 dBm at baseband, -138 dBm at RF
DSP Error Status: 8
25 Jul
25 Jul
12:54 p.m.
Hi,
I have built Osmocommbb with testing branch and I want
to run Mobile app
allowing me to make a call via my local network.
All goes well in the build but I am unable to register on my own network
while using a genuine network sim.
This is output from my compal_e88/layer1.compalram.bin.
As you can see all looks good with signal levels fairly ok until this point
and then level drops to -138 dbm and there it stays on all chanells.
I have tried this with 3 different sims and all is the same.
Can someone help?
Use master, not testing.
30 Jul
30 Jul
10:54 a.m.
Hi I have same problem.
But in case with master with TX enabled, it just hang up ?
OsmocomBB> enable
OsmocomBB# sim reader 1
OsmocomBB#
% (MS 1)
% Searching network...
% (MS 1)
% Trying to registering with network...
Connection closed by foreign host.
????
msgb(0x1638020): Not enough headroom msgb_push (4271669080 < 7)
backtrace() returned 10 addresses
/usr/local/lib/libosmocore.so.4(osmo_panic+0xb9) [0x7f2b4ea57929]
/usr/local/lib/libosmogsm.so.5(lapdm_phsap_up+0x16f) [0x7f2b4e62378f]
./mobile() [0x43981c]
./mobile() [0x439fce]
/usr/local/lib/libosmocore.so.4(osmo_wqueue_bfd_cb+0x93) [0x7f2b4ea550d3]
/usr/local/lib/libosmocore.so.4(osmo_select_main+0x1b1) [0x7f2b4ea54171]
./mobile() [0x404be7]
/lib/x86_64-linux-gnu/libc.so.6(__libc_start_main+0xfd) [0x7f2b4e099eed]
./mobile() [0x404d59]
Signal 6 received.
full talloc report on 'layer2 context' (total 40828 bytes in 53 blocks)
Layer2 contains 424 bytes in 1 blocks (ref
0) 0x1638020
GSM 04.08 L3 contains 456 bytes in 1 blocks (ref
0) 0x1639e10
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x1638930
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x16388c0
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x1638850
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x16387e0
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x1638770
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x1638700
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x1638690
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x1638620
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x16385b0
struct gsm_sub_plmn_list contains 24 bytes in 1 blocks (ref
0) 0x1638540
struct gsm_sim_handler contains 32 bytes in 1 blocks (ref
0) 0x1634810
struct gsm_sim_handler contains 32 bytes in 1 blocks (ref
0) 0x1634890
struct gsm_sim_handler contains 32 bytes in 1 blocks (ref
0) 0x1634910
struct gsm48_sysinfo contains 1452 bytes in 1 blocks (ref
0) 0x1637970
struct gsm48_sysinfo contains 1452 bytes in 1 blocks (ref
0) 0x1637360
struct gsm48_sysinfo contains 1452 bytes in 1 blocks (ref
0) 0x1636d50
struct gsm48_sysinfo contains 1452 bytes in 1 blocks (ref
0) 0x1636740
struct gsm48_sysinfo contains 1452 bytes in 1 blocks (ref
0) 0x1635e60
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635dc0
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635d20
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635c80
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635be0
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635b40
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635aa0
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635a00
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635960
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x16358c0
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635820
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x1635780
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x16356e0
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162d010
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162cf70
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162ced0
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162ce30
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162cd90
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162ccf0
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162d420
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162d380
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162d2e0
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162d240
struct gsm322_neighbour contains 64 bytes in 1 blocks (ref
0) 0x162d1a0
struct gsm48_sysinfo contains 1452 bytes in 1 blocks (ref
0) 0x16350d0
telnet_connection contains 89 bytes in 2 blocks (ref
0) 0x1634bf0
struct telnet_connection contains 88 bytes in 1 blocks
(ref 0) 0x1634c50
struct gsm322_ba_list contains 192 bytes in 1 blocks (ref
0) 0x1634fb0
struct gsm322_ba_list contains 192 bytes in 1 blocks (ref
0) 0x1634e90
struct gsm322_ba_list contains 192 bytes in 1 blocks (ref
0) 0x1634990
struct osmocom_ms contains 28704 bytes in 1 blocks (ref
0) 0x162d590
/root/.osmocom/bb contains 29 bytes in 1 blocks (ref
0) 0x15ca730
main.c:240 contains 29 bytes in 1 blocks (ref
0) 0x15ca6b0
Aborted
On Fri, Jul 25, 2014 at 12:54 PM, Sylvain Munaut <246tnt(a)gmail.com> wrote:
Hi,
--
Milinko Isakovic, CEO
CS Network Solutions Limited
72 Blythe Road, West Kensington, London W14 0HB
London Switchboard: +442071933539
Belgrade Operations: +381112620152
Personal mobille: +381666666666
Web: www.cs-networks.net
<http://www.facebook.com/smsanywhere> <https://twitter.com/cs_networks>
<http://www.linkedin.com/company/cs-networks>
<http://www.youtube.com/csnetworks>
--------------------------
This message (including any attachments) is confidential and may be
privileged. If you have received it by mistake please notify the sender by
return e-mail and delete this message from your system. Any unauthorized
use or dissemination of this message in whole or in part is strictly
prohibited. Please note that e-mails are susceptible to change. CS Networks
shall not be liable for the improper or incomplete transmission of the
information contained in this communication nor for any delay in its
receipt or damage to your system. CS Networks does not guarantee that the
integrity of this communication has been maintained nor that this
communication is free of viruses, interceptions or interference.
I have built Osmocommbb with testing branch and I
want to run Mobile app
allowing me to make a call via my local network.
All goes well in the build but I am unable to register on my own network
while using a genuine network sim.
This is output from my compal_e88/layer1.compalram.bin.
As you can see all looks good with signal levels fairly ok until this
point
and then level drops to -138 dbm and there it
stays on all chanells.
I have tried this with 3 different sims and all is the same.
Can someone help?
Use master, not testing.
12:28 p.m.
On Wed, Jul 30, 2014 at 10:54:39AM +0200, Milinko Isakovic wrote:
Hi I have same problem.
Hi,
msgb(0x1638020): Not enough headroom msgb_push
(4271669080 < 7)
backtrace() returned 10 addresses
/usr/local/lib/libosmocore.so.4(osmo_panic+0xb9) [0x7f2b4ea57929]
/usr/local/lib/libosmogsm.so.5(lapdm_phsap_up+0x16f) [0x7f2b4e62378f]
./mobile() [0x43981c]
./mobile() [0x439fce]
/usr/local/lib/libosmocore.so.4(osmo_wqueue_bfd_cb+0x93) [0x7f2b4ea550d3]
/usr/local/lib/libosmocore.so.4(osmo_select_main+0x1b1) [0x7f2b4ea54171]
./mobile() [0x404be7]
/lib/x86_64-linux-gnu/libc.so.6(__libc_start_main+0xfd) [0x7f2b4e099eed]
./mobile() [0x404d59]
we are still waiting for a patch. The LAPDm code is using l2h/l3h but
in rx_l1_rach_conf it is not initialized at all.
Patches welcome.
holger
21 Aug
21 Aug
6:04 a.m.
Hi,
On 07/30/2014 07:28 AM, Holger Hans Peter Freyther wrote:
On Wed, Jul 30, 2014 at 10:54:39AM +0200, Milinko
Isakovic wrote:
The attached patch works for me. Anything I've missed?
Hi I have same problem.
Hi,
msgb(0x1638020): Not enough headroom msgb_push
(4271669080 < 7)
backtrace() returned 10 addresses
/usr/local/lib/libosmocore.so.4(osmo_panic+0xb9) [0x7f2b4ea57929]
/usr/local/lib/libosmogsm.so.5(lapdm_phsap_up+0x16f) [0x7f2b4e62378f]
./mobile() [0x43981c]
./mobile() [0x439fce]
/usr/local/lib/libosmocore.so.4(osmo_wqueue_bfd_cb+0x93) [0x7f2b4ea550d3]
/usr/local/lib/libosmocore.so.4(osmo_select_main+0x1b1) [0x7f2b4ea54171]
./mobile() [0x404be7]
/lib/x86_64-linux-gnu/libc.so.6(__libc_start_main+0xfd) [0x7f2b4e099eed]
./mobile() [0x404d59]
we are still waiting for a patch. The LAPDm code is using l2h/l3h but
in rx_l1_rach_conf it is not initialized at all.
Patches welcome.
holger
--
Igor Almeida
22 Aug
22 Aug
5:50 p.m.
On Thu, Aug 21, 2014 at 01:04:38AM -0300, Igor Almeida wrote:
Hi!
dl = (struct l1ctl_info_dl *) msg->l1h;
+ msg->l2h = msg->l3h = dl->payload;
yes, looks fine. I had msg->l2h = msg->l3h = msg->tail but
dl->payload should probably work as well. I will leave it for
Sylvain/Andreas to comment.
thanks a lot for the patch
holger
5:58 p.m.
On Fri, Aug 22, 2014 at 5:50 PM, Holger Hans Peter Freyther
<holger(a)freyther.de> wrote:
On Thu, Aug 21, 2014 at 01:04:38AM -0300, Igor Almeida
wrote:
Hi!
I'll give it a shot this week end when I have a osmocom-bb phone handy
and merge it.
Cheers,
Sylvain
dl = (struct l1ctl_info_dl *) msg->l1h;
+ msg->l2h = msg->l3h = dl->payload;
yes, looks fine. I had msg->l2h = msg->l3h = msg->tail but
dl->payload should probably work as well. I will leave it for
Sylvain/Andreas to comment.
thanks a lot for the patch
7 Sep
7 Sep
10:22 a.m.
dl = (struct l1ctl_info_dl *) msg->l1h;
+ msg->l2h = msg->l3h = dl->payload;
yes, looks fine. I had msg->l2h = msg->l3h = msg->tail but
dl->payload should probably work as well. I will leave it for
Sylvain/Andreas to comment.
thanks a lot for the patch
3523
days inactive
3567
days old
baseband-devel@lists.osmocom.org
7 comments
5 participants
participants (5)
-
Holger Hans Peter Freyther -
Igor Almeida -
Milinko Isakovic -
Sylvain Munaut -
tom mc loughlin