28 Jan
2013
28 Jan
'13
7:34 p.m.
Hello,
I've found a very interesting article about SciphoneDream G2 published on your webpage
at http://bb.osmocom.org/trac/wiki/SciphoneDreamG2 that covers pretty detailed information
about MT6235 SoC, bootstrapping as well as JTAG. This is the only article I have ever
found on internet about MTK SoC and JTAG.
What I am trying to accomplish is to access NAND flash and write to it over JTAG (in order
to recover from corruption after bad flash) on MTK8555 SoC which according to my in-depth
research and analysis has very similar architecture to MT6235. If I can't write to
NAND over JTAG but would be able to launch u-boot that would be a solution too. I am very
good at ARM assembly and debugging, however I am not very experienced with JTAG. Do you
think you (or anyone else) could help me out, by giving me guidance what hardware,
software, config files should I use to make JTAG work on this SoC ? Any help or advise
would be more then appreciated!
If you are a wrong person I contacted, I apologize for the inconvenience.
Many thanks in advance!
Dwayne
31 Jan
31 Jan
7:14 a.m.
Hi Dwayne,
On Mon, Jan 28, 2013 at 7:34 PM, <teslarode(a)yahoo.com> wrote:
I've found a very interesting article about SciphoneDream G2 published on
your webpage at http://bb.osmocom.org/trac/wiki/SciphoneDreamG2 that
covers pretty detailed information about MT6235 SoC, bootstrapping as well
as JTAG. This is the only article I have ever found on internet about MTK
SoC and JTAG.
What I am trying to accomplish is to access NAND flash and write to it over
JTAG (in order to recover from corruption after bad
flash) on MTK8555 SoC
which according to my in-depth research and analysis has very similar
architecture to MT6235. If I can't write to NAND over JTAG but would be
able to launch u-boot that would be a solution too. I am very good at ARM
assembly and debugging, however I am not very experienced with JTAG. Do you
think you (or anyone else) could help me out, by giving me guidance what
hardware, software, config files should I use to make JTAG work on this SoC
? Any help or advise would be more then appreciated!
For JTAG debugging of MT6235 I used commercial debugger Trace32 from
Lauterbach. I know that it was also working with OpenOCD.
In case when your NAND is corrupted completely it can be pretty hard to get
your board running. The biggest problem is in initialising SDRAM/DDR RAM
controller, to get external RAM working.
When I had MT6235 running (booting without issues), I was able to break
running processor and load my code into external RAM as RAM was already
initialised by bootloader.
Later on when I learnt Mediatek boot process and new where bootloader is
placed in NAND, I extracted SDRAM initialisation procedure. NAND layout is
described in the link you mentioned.
MT6235 had static RAM (64KB or 128KB) available from start (without
initialisation), and you could place your code for SoC init there (this is
where DRAM initialisation was copied from NAND and then executed).
I have never flashed NAND using JTAG on MT6235 as I haven't found it
useful. I focused on getting U-Boot running and this is the first place
which has flash driver for NAND found on Sciphone G2.
In case of any further questions you can contact me directly as this group
covers different topics.
BR,
Marcin
4109
days inactive
4112
days old
baseband-devel@lists.osmocom.org
1 comments
2 participants
participants (2)
-
Marcin Mielczarczyk -
teslarode＠yahoo.com