Nokia AirScale GSM Packet Abis/IUA support in OsmoBSC ? working lab hardware available
Hello, we are trying to bring up a Nokia AirScale GSM BTS in an isolated laboratory using OsmoBSC 1.15.0. Hardware: Nokia AirScale ASIB + ABIA + FXDA GSM900 radio (472083A). BTS software: SBTS25R2, GSM RAT 25R2. The BTS is configured for Nokia Packet Abis over IP. BTS GSM IP: 172.19.107.97 BSC IP: 172.17.208.121 SCTP/IUA port: 49152 We developed a small IUA ↔ libosmo-abis bridge and currently achieve: SCTP association OK ASPUP / ASPUP_ACK OK ASPAC / ASPAC_ACK OK IUA AS ACTIVE OK Nokia uses one SCTP stream and PPID 1. The Routing Context / Interface Identifier observed is 0x00028e00 (BCF ID 654). OsmoBSC establishes its local LAPD link using SAPI 62 / TEI 1 and starts Nokia OML bootstrap. However the AirScale never establishes OMUSIG at application level. WebEM reports: Fault 2412: OMU signaling connection failure in Abis interface. We tested both sending the Nokia RESET_REQ after AS ACTIVE and an IUA TEI-first procedure. SCTP acknowledges the packets, but no Nokia OML response is received. The same behavior has been reproduced with two SBTS25R2 software builds, and an unrelated software-fallback alarm has now been eliminated. We understand that current OsmoBSC Nokia support is nokia-e1, including recent Flexi Multiradio support, while Nokia Packet Abis/IP support is not yet implemented. We have a complete Nokia AirScale GSM laboratory setup available and can provide remote access, packet captures, WebEM logs and test patches if somebody is interested in implementing/debugging nokia-ip support. Our immediate objective is to bring at least one GSM TRX/BCCH on air in the isolated RF laboratory. We can provide: PCAP of the SCTP/IUA association complete iua bridge source code OsmoBSC logs AirScale configuration and runtime exports Nokia alarm information interactive access to the physical AirScale BTS Is anyone interested in helping us identify the missing Packet Abis/IUA bootstrap procedure or in working on Nokia IP Abis support in OsmoBSC? Thank you.
Hi Ciccio,
we are trying to bring up a Nokia AirScale GSM BTS in an isolated laboratory using OsmoBSC 1.15.0. [...] The BTS is configured for Nokia Packet Abis over IP.
I am the developer who added preliminary support to OsmoBSC (much more work is still needed) for Nokia Flexi Multiradio BTS with traditional E1 Abis. My Flexi MR BTS (ESMB system unit + choice of FXCB or FXFB radio module, for GSM850 or PCS1900 band) supports both traditional E1 Abis and Packet Abis over IP: I have FIQB transport module fitted into ESMB, which implements both E1 and Ethernet ports for Abis, with BTS software supporting both Abis types at the high level. As a further clarification, I work with these old Nokia BTS not merely for fun, but because I seek to deploy them in real production operation - see www.usa2g.org. Note that I said "production" operation, rather than "commercial": the company in question is a non-profit org, hence the network we seek to build, serving those human users who wish to use GSM/2G as their personal cellphone, cannot be called commercial. But we do seek the full quality level of a real production network, no worse than commercial ones, despite ours being non-profit and hence non-commercial. Back to Nokia's proprietary Packet Abis over IP, I am very pleased to see that you made more progress with it than I did! I do feel, however, that jumping directly from Flexi MR with E1 Abis (newest Nokia hw config that works today) to the much newer AirScale you are working with may be too big of a jump - too many variables changing at once. Instead I wonder if it might make sense to take a more incremental approach: first get Packet Abis (IP) working on Flexi MR, then on Multiradio 10 (I don't have MR10 hw at the moment, but I should have no problem justifying the purchase of an FSMF unit when we reach that point), and only then the bravest move on AirScale. What do you think? You offered remote access to your AirScale hw setup, and I can likewise provide remote access to the Flexi MR BTS in my lab, with both E1 and IP interfaces wired up and accessible. But let me ask you: can you get access to Nokia's official BSC, whatever it is called, and get a pcap of Nokia BTS connecting to their own official BSC via Packet Abis? My hunch is that we will need such a trace before we can get Packet Abis working with any of those BTS models - in the absence of such working example, we are just blindly stabbing in the dark. Also please treat this response from me as very preliminary: right now I am working in a different area and it will probably be several months before I can properly switch my attention to Nokia BTS details. But when I do eventually make that attention switch, I will keep you in mind, especially if I decide to take another stab at Packet Abis, as opposed to sticking with E1 and building an FPGA-based adapter that would make our E1 Abis interface more efficient than the sw-heavy approach currently adopted in Osmocom. M~
participants (2)
-
Ciccio Franco -
Mychaela Falconia