please verify my multidrop-config

hello list, i'd like you to go with me thru my setup of 2 bs11 and verify it. it looks like this: E1 E1 PC------BTS0------BTS1 let's begin with the bs11_config outputs bts0: LMT LOGON: ACK PHASE: 3 Normal MBCCU0: Load MBCCU1: No Load Abis-link: Restoring BS11 ATTRIBUTES: BS-11 ESN PCB Serial Number: 001104 BS-11 ESN Hardware Code Number: 135-2044/03.07 BS-11 ESN Firmware Code Number: 135-2044/03.07 PLL Set Value=1006, Work Value=1038 SITE MANAGER ATTRIBUTES: E1 Channel: Port=0 Timeslot=1 (Full Slot) TEI: 25 BS11 Line Interface ATTRIBUTES: PLL Mode: Standalone BS11 CCLK ATTRIBUTES: CCLK Accuracy: High (1) CCLK Type=0 BS11 Power Amplifier 0 ATTRIBUTES: TRX Power: 30mW (GSM) BPORT0 ATTRIBUTES: Line Configuration: Multi-Drop (1) BPORT1 ATTRIBUTES: Line Configuration: Multi-Drop (1) LMT LOGOFF: ACK and that's bts1: LMT LOGON: ACK PHASE: 3 Normal MBCCU0: Load MBCCU1: No Load Abis-link: Restoring BS11 ATTRIBUTES: BS-11 ESN PCB Serial Number: 001112 BS-11 ESN Hardware Code Number: 135-2044/03.03 BS-11 ESN Firmware Code Number: 135-2044/03.03 PLL Set Value=1073, Work Value=1073 SITE MANAGER ATTRIBUTES: E1 Channel: Port=1 Timeslot=17 (Full Slot) TEI: 25 BS11 Line Interface ATTRIBUTES: PLL Mode: Standalone BS11 CCLK ATTRIBUTES: CCLK Accuracy: High (1) CCLK Type=0 BS11 Power Amplifier 0 ATTRIBUTES: TRX Power: 30mW (GSM) BPORT0 ATTRIBUTES: Line Configuration: Star (0) BPORT1 GET ATTR NACK <--- do i have to worry about his? LMT LOGOFF: ACK here we go with openbsc.cfg. i use only trx0 of each bts. don't ask why i did something like this or like that, i just adapted the openbsc.cfg-file from the packet to my timeslots configured ! ! OpenBSC configuration saved from vty ! ! password foo ! line vty no login ! network network country code 262 mobile network code 10 short name Y-Phone long name Yodaphone handover 1 bts 0 type bs11 band GSM900 cell_identity 1 location_area_code 1 training_sequence_code 7 base_station_id_code 63 oml e1 line 0 timeslot 1 sub-slot full oml e1 tei 25 <-- i use tei 25 for the oml of bts1, too. correct? trx 0 arfcn 121 max_power_red 0 rsl e1 line 0 timeslot 1 sub-slot full <-- the same e1 timeslot for oml is used here for the ccch. rsl e1 tei 1 | correct? timeslot 0 | i'd say weird phys_chan_config CCCH+SDCCH4 | e1 line 0 timeslot 1 sub-slot full <-- timeslot 1 phys_chan_config TCH/F e1 line 0 timeslot 2 sub-slot 1 timeslot 2 phys_chan_config TCH/F e1 line 0 timeslot 2 sub-slot 2 timeslot 3 phys_chan_config TCH/F e1 line 0 timeslot 2 sub-slot 3 timeslot 4 phys_chan_config TCH/F e1 line 0 timeslot 3 sub-slot 0 timeslot 5 phys_chan_config TCH/F e1 line 0 timeslot 3 sub-slot 1 timeslot 6 phys_chan_config TCH/F e1 line 0 timeslot 3 sub-slot 2 timeslot 7 phys_chan_config TCH/F e1 line 0 timeslot 3 sub-slot 3 bts 1 type bs11 band GSM900 location_area_code 2 training_sequence_code 7 base_station_id_code 63 oml e1 line 0 timeslot 17 sub-slot full <-- harald told me line has to be 0, but i dont understand why. i configured 2 fragments on the misdn driver, with d-channel on ts 1 and 17, the rest b-channels. each fragment is a device,right? (0 and 1). Each device corresponds to a port in bs11_config and a line here, right ? oml e1 tei 25 <-- here again: all oml e1 teis identical? trx 0 arfcn 122 max_power_red 0 rsl e1 line 0 timeslot 17 sub-slot full rsl e1 tei 2 timeslot 0 phys_chan_config CCCH+SDCCH4 <--here we go with line(=port=id) 1, since fragment 2 starts ad device id 1 on e1 ts 17 as d-channel e1 line 1 timeslot 17 sub-slot full timeslot 1 phys_chan_config SDCCH8 e1 line 1 timeslot 18 sub-slot 1 timeslot 2 phys_chan_config TCH/F e1 line 1 timeslot 18 sub-slot 2 timeslot 3 phys_chan_config TCH/F e1 line 1 timeslot 18 sub-slot 3 timeslot 4 phys_chan_config TCH/F e1 line 1 timeslot 19 sub-slot 0 timeslot 5 phys_chan_config TCH/F e1 line 1 timeslot 19 sub-slot 1 timeslot 6 phys_chan_config TCH/F e1 line 1 timeslot 19 sub-slot 2 timeslot 7 phys_chan_config TCH/F e1 line 1 timeslot 19 sub-slot 3 and for the final: the output of bsc_hack during start: 2 devices found id: 0 Dprotocols: 00000018 Bprotocols: 0000000e protocol: 4 nrbchan: 14 name: hfc-e1.1-1 activate bchan activate bchan DB: Database initialized. DB: Database prepared. since line 1 isnt used for bts1 oml, only device id 0 with d-channel on ts 1 is activated. but im quite sure this is a mistake, i need 2 devices for 2 bts. right? this config dont work at all. bts1 not recognised, bts0 is recognised but cant handle calls. the handys are callable and ring, but no data is transmitted. please give me as much feedback as possible mni tnx T. -- Wer Rechtschreibfehler findet, darf sie behalten!