Hello,
I used step-by-step instruction from the
osmocom.org site.
Here is my openbsc config:
====
e1_input
e1_line 0 driver ipa
network
network country code 250
mobile network code 77
short name ABC
long name ABC
auth policy accept-all
location updating reject cause 13
encryption a5 0
neci 1
rrlp mode none
mm info 1
handover 0
handover window rxlev averaging 10
handover window rxqual averaging 1
handover window rxlev neighbor averaging 10
handover power budget interval 6
handover power budget hysteresis 3
handover maximum distance 9999
timer t3101 10
timer t3103 0
timer t3105 0
timer t3107 0
timer t3109 4
timer t3111 0
timer t3113 60
timer t3115 0
timer t3117 0
timer t3119 0
timer t3141 0
bts 0
type nanobts
band DCS1800
cell_identity 0
location_area_code 1
training_sequence_code 7
base_station_id_code 63
ms max power 15
cell reselection hysteresis 4
rxlev access min 0
channel allocator ascending
rach tx integer 9
rach max transmission 7
ip.access unit_id 1234 0
oml ip.access stream_id 255 line 0
gprs mode gprs
gprs routing area 0
gprs cell bvci 2
gprs nsei 101
gprs nsvc 0 nsvci 101
gprs nsvc 0 local udp port 23000
gprs nsvc 0 remote udp port 23000
gprs nsvc 0 remote ip 192.168.168.98
trx 0
rf_locked 0
arfcn 666
nominal power 23
max_power_red 20
rsl e1 tei 0
timeslot 0
phys_chan_config CCCH+SDCCH4
timeslot 1
phys_chan_config PDCH
timeslot 2
phys_chan_config PDCH
timeslot 3
phys_chan_config TCH/F
timeslot 4
phys_chan_config TCH/F
timeslot 5
phys_chan_config TCH/F
timeslot 6
phys_chan_config TCH/F
timeslot 7
phys_chan_config TCH/F
====
Here is my osmo-sgsn.cfg
====
sgsn
gtp local-ip 192.168.168.98
ggsn 0 remote-ip 192.168.168.230
ggsn 0 gtp-version 1
!
ns
timer tns-block 3
timer tns-block-retries 3
timer tns-reset 3
timer tns-reset-retries 3
timer tns-test 30
timer tns-alive 3
timer tns-alive-retries 10
encapsulation udp local-ip 192.168.168.98
encapsulation udp local-port 23000
encapsulation framerelay-gre enabled 0
====
Here is my ggsn.cfg
===
listen 192.168.168.230
net 192.168.168.0/24
dynip 192.168.168.240/30
===
Here is my open-bts.cfg
===
bts 0
band 1800
ipa unit-id 1234 0
oml remote-ip 192.168.168.98
===
Regards,
Sergey.
On Aug 14, 2013, at 8:17 PM, Holger Hans Peter Freyther wrote:
On Wed, Aug 14, 2013 at 07:42:30PM +0400, Sergey V.
Efimov wrote:
Hello All,
<0011> gprs_bssgp.c:1000 NSEI=101/BVCI=2 Rejecting PDU type 1 for unknown BVCI
<0011> gprs_bssgp_util.c:103 BSSGP BVCI=0 Tx STATUS, cause=Unknown BVCI
<0011> gprs_bssgp.c:1000 NSEI=101/BVCI=2 Rejecting PDU type 1 for unknown BVCI
<0011> gprs_bssgp_util.c:103 BSSGP BVCI=0 Tx STATUS, cause=Unknown BVCI
without your NITB/BSC config it is difficult to judge. What doesn't work for
sure is to restart the SGSN once the PCU has exchanged some messages with it.
holger