If you’d called me like I offered, I could have explained a few things.
There is no need to enter a TG on the fly. Just put the desired TG id’s (in decimal)
into the whitelist field of trunk.tsv (hills.tsv) and op25 will only track those TG’s.
Now if you want to setup scan priorities then make sure you’re using the hills-tgids.tsv
file that I made and sent you. In that file you’ll notice tab separated column all the
way to the right of each line with the number “3” populated.
This is the default scan priority scan feature in Graham’s boatbod fork. The scan
priority numbers range from 1-5 with 5 being the highest and 1 being the lowest. Set
your desired TG’s in that file with a number that corresponds to the desired priority.
You don’t need to set all of the TG’s found in that file, only those you have in your
whitelist as op25 is going to ignore the others.
No entries in the whitelist field means op25 will track all TG’s on the system. Only add
those TG’s that you’re are interested in.
Bill
From: op25-dev(a)yahoogroups.com <op25-dev(a)yahoogroups.com>
Sent: Monday, December 10, 2018 7:20 PM
To: op25-dev(a)yahoogroups.com
Subject: RE: [op25-dev] Re: How To Hold On A Talk Group
Well, I think that hold hotkey only works when a talk group pops up while the software is
running. That means you'd have to wait until the talk group you wanna listen to
becomes active AND OP25 happens to stop on it (and not some other talk group). But I
don't see a way to just outright type in an ID number for a TG that I wanna listen
to..
Like suppose cop A tells cop B, "Go to channel 2". If I know the TG ID for ch.
2, I'd want to be able to quickly switch to it at that moment. But I'm not seeing
a way to do that, or is there?
trunktracker(a)tampabay.rr.com <mailto:trunktracker@tampabay.rr.com>
From: op25-dev(a)yahoogroups.com <mailto:op25-dev@yahoogroups.com>
[mailto:op25-dev@yahoogroups.com]
Sent: Monday, December 10, 2018 1:39 AM
To: op25-dev(a)yahoogroups.com <mailto:op25-dev@yahoogroups.com>
Subject: [op25-dev] Re: How To Hold On A Talk Group
Have you read op25/op25/gr-op25_repeater/apps/README?
Here is part of that file:
TERMINAL OPERATION
==================
After starting rx.py if plotting is in use a separate gnuplot window
should open. You must click on the terminal window to restore it to
focus, otherwise all keystrokes are consumed by gnuplot. Once in the
terminal window there are several keyboard commands:
h - hold
l - lockout
s - skip
q - quit program
, - decrease fine tune by 100Hz
. - increase fine tune by 100Hz
< - decrease fine tune by 1200Hz
- increase fine tune by 1200Hz
1 - toggle fft
plot
2 - toggle constellation plot (cqpsk)
3 - toggle symbol plot
4 - toggle datascope plot (fsk4)
5 - toggle mixer plot
There are also two experimental commands (should not be used in -T mode)
f - manually change frequencies
t - if currently tuned to a CC, autostart scanning talkgroups
The "t" command allows trunk tracking without setting up a trunking TSV
file. However running with the -T <filename> command line option is
preferred as that allows use of white/black lists and talkgroup tags files.
If the terminal window freezes there may have been a crash. Press Ctrl-Z
to suspend the program and examine stderr.2 for error messages. If there
is a traceback please report the full traceback (and the command line) to
the mail list.