Please advice - C115 FMTOOL - Ramloader Aborted
Dear Folks, After much deliberation and waiting I finally rxed a C115 and the T1 Cable USB. I am running Backtrack 5 and have compiled the Osmocomm bundles and all executable seem to be present. When i plug om the Jack cable and press the power switch i get this :- ~/osmocom-bb/osmocom-bb/src/host/osmocon# ./osmocon -p /dev/ttyUSB0 -m c123xor ../../target/firmware/board/compal_e88/layer1.compalram.bin got 1 bytes from modem, data looks like: 00 . got 2 bytes from modem, data looks like: 2f 00 /. got 4 bytes from modem, data looks like: 1b f6 02 00 .... got 1 bytes from modem, data looks like: 41 A got 1 bytes from modem, data looks like: 01 . got 1 bytes from modem, data looks like: 40 @ Received PROMPT1 from phone, responding with CMD read_file(../../target/firmware/board/compal_e88/layer1.compalram.bin): file_size=48808, hdr_len=4, dnload_len=48815 got 1 bytes from modem, data looks like: 66 f got 1 bytes from modem, data looks like: 74 t got 1 bytes from modem, data looks like: 6d m got 1 bytes from modem, data looks like: 74 t got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 6c l Received FTMTOOL from phone, ramloader has aborted got 1 bytes from modem, data looks like: 65 e got 1 bytes from modem, data looks like: 72 r got 1 bytes from modem, data looks like: 72 r got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 72 r got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: 00 . Have have tried with Xor and without. What am I missing folks - please advice as have been at this a while now with same results. Thanks in advance. Raz
Hi Raz, I have a c115 as well and I use the option -i 10 to load layer1. Anyway, with one of my cables I had problems at the beginning, until I realized that the plastic around the jack was impeding the jack from being properly plugged in. I cut it off and now it works. regards, Loretta -- View this message in context: http://baseband-devel.722152.n3.nabble.com/Please-advice-C115-FMTOOL-Ramload... Sent from the baseband-devel mailing list archive at Nabble.com.
Hi, On 01.07.2011 16:51, Raz Sharif wrote:
Have have tried with Xor and without. What am I missing folks - please advice as have been at this a while now with same results.
Maybe your machine is too slow, but you could try this: http://lists.osmocom.org/pipermail/baseband-devel/2011-February/001407.html I'm not sure if the patch still applies correctly though. If that doesn't work, here's another thing to try: http://lists.osmocom.org/pipermail/baseband-devel/2011-January/001053.html Regards, Steve
Hi, As I mailed before I also have a non working C115, but I have 3 working so I have something to compare. I suspect a hardware problem on my side, but I tried your tips
Maybe your machine is too slow, but you could try this: http://lists.osmocom.org/pipermail/baseband-devel/2011-February/001407.html I'm not sure if the patch still applies correctly though.
No it doesn't but I compiled it and it did not help me.
If that doesn't work, here's another thing to try: http://lists.osmocom.org/pipermail/baseband-devel/2011-January/001053.html
Tried that too without result. I also confirmed by breaking the TX line to the phone (from the PC) that this error (FTMTOOL error) then also happens. So it can also be caused by a faulty cable, faulty connector or blown UART pin on the Calypso. Best regards, Job
Hi, On 02.07.2011 15:37, Job wrote:
As I mailed before I also have a non working C115, but I have 3 working so I have something to compare. I suspect a hardware problem on my side, but I tried your tips
Yes, in your case I'd say the RX line of your third phone is somehow broken as well. Regards, Steve
participants (4)
-
Job -
Raz Sharif -
screaming-pain -
Steve Markgraf