This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/OpenBSC@lists.osmocom.org/.
Gullik Webjorn gullik.webjorn at corevalue.seSorry to clutter the list......last was a cut'n'paste error.... Gullik On 2019-01-10 22:31, Gullik Webjorn wrote: > > I have now built osmo-trx-lms and osmo-bts-trx from source on an i386 > platform. > > I have beacon, and two phones registered, the configuration from msc > and up is the one > > I had three weeks ago, which more or less worked, but with large > stability problems. > > I guess *this* report is the most interesting for you now.... > > I build from the "master", and target debian9 on i386. > > > I have not been able to make a call yet, possibly because I might have > messed up some > > library the MSC is dependent on, but I will work on that. > > What is interesting is that bts 0 trx 0 is running trx-uhd with a > B100, and seems quite stable. > > Moreover, bts 1 trx 0 is running on the i386 and seems happy so far, > after 30 minutes. > > This is Limesdr mini. > > > I have just copied the bts0 to trx 0 section from my original config, > duplicated it and changed > > bts0 to bts1, and the ipa unit-id 1805 0, and of course the ip addresses. > > I will comment the various lines in my configs, as I have understood > them, and look forward to your > > comments, or maybe a keyword list explaining what each parameter is > used for. > > > ! osmo-bsc default configuration > ! (assumes STP to run on 127.0.0.1 and uses default point codes) > ! > e1_input > e1_line 0 driver ipa > network > network country code 1 > mobile network code 1 > encryption a5 0 > neci 1 > paging any use tch 0 > handover 0 > handover algorithm 1 > handover1 window rxlev averaging 10 > handover1 window rxqual averaging 1 > handover1 window rxlev neighbor averaging 10 > handover1 power budget interval 6 > handover1 power budget hysteresis 3 > handover1 maximum distance 9999 > dyn_ts_allow_tch_f 0 > periodic location update 30 > *bts 0** > *** type sysmobts > band DCS1800 > cell_identity 0 > location_area_code 1 > base_station_id_code 63 > ms max power 15 > cell reselection hysteresis 4 > rxlev access min 0 > radio-link-timeout 32 > channel allocator ascending > rach tx integer 9 > rach max transmission 7 > channel-descrption attach 1 > channel-descrption bs-pa-mfrms 5 > channel-descrption bs-ag-blks-res 1 > early-classmark-sending forbidden > * ip.access unit_id 1801 0** > * oml ip.access stream_id 255 line 0 > codec-support fr > gprs mode none > trx 0 > rf_locked 0 > * arfcn 871** > * nominal power 20 > ! to use full TRX power, set max_power_red 0 > max_power_red 3 > rsl e1 tei 0 > timeslot 0 > phys_chan_config CCCH+SDCCH4 > hopping enabled 0 > timeslot 1 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 2 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 3 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 4 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 5 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 6 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 7 > phys_chan_config TCH/F > hopping enabled 0 > *bts 1** > *** type sysmobts > band DCS1800 > cell_identity 0 > location_area_code 1 > base_station_id_code 63 > ms max power 15 > cell reselection hysteresis 4 > rxlev access min 0 > radio-link-timeout 32 > channel allocator ascending > rach tx integer 9 > rach max transmission 7 > channel-descrption attach 1 > channel-descrption bs-pa-mfrms 5 > channel-descrption bs-ag-blks-res 1 > early-classmark-sending forbidden > * ip.access unit_id 1805 0** > * oml ip.access stream_id 255 line 0 > codec-support fr > gprs mode none > trx 0 > rf_locked 0 > * arfcn 881** > * nominal power 20 > ! to use full TRX power, set max_power_red 0 > max_power_red 3 > rsl e1 tei 0 > timeslot 0 > phys_chan_config CCCH+SDCCH4 > hopping enabled 0 > timeslot 1 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 2 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 3 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 4 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 5 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 6 > phys_chan_config TCH/F > hopping enabled 0 > timeslot 7 > phys_chan_config TCH/F > hopping enabled 0 > msc 0 > no bsc-welcome-text > no bsc-msc-lost-text > no bsc-grace-text > type normal > allow-emergency allow > amr-config 12_2k forbidden > amr-config 10_2k forbidden > amr-config 7_95k forbidden > amr-config 7_40k forbidden > amr-config 6_70k forbidden > amr-config 5_90k allowed > amr-config 5_15k forbidden > amr-config 4_75k forbidden > codec-list fr1 fr2 fr3 hr1 hr3 > mgw remote-ip 127.0.0.1 > mgw remote-port 2427 > mgw local-port 2727 > mgw endpoint-range 1 31 > bsc > mid-call-timeout 0 > no missing-msc-text > > Does this look OK to you?? > > Regards, > > Gullik > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.osmocom.org/pipermail/openbsc/attachments/20190110/d5777b52/attachment.htm>