<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body text="#000000" bgcolor="#FFFFFF">
<p>Sorry to clutter the list......last was a cut'n'paste error....</p>
<p>Gullik<br>
</p>
<div class="moz-cite-prefix">On 2019-01-10 22:31, Gullik Webjorn
wrote:<br>
</div>
<blockquote type="cite"
cite="mid:26ba2180-3a42-b70d-46ea-92a87348a27b@corevalue.se">
<meta http-equiv="content-type" content="text/html; charset=UTF-8">
<p>I have now built osmo-trx-lms and osmo-bts-trx from source on
an i386 platform.</p>
<p>I have beacon, and two phones registered, the configuration
from msc and up is the one</p>
<p>I had three weeks ago, which more or less worked, but with
large stability problems.</p>
<p>I guess *this* report is the most interesting for you now....</p>
<p>I build from the "master", and target debian9 on i386.<br>
</p>
<p><br>
</p>
<p>I have not been able to make a call yet, possibly because I
might have messed up some</p>
<p>library the MSC is dependent on, but I will work on that.</p>
<p>What is interesting is that bts 0 trx 0 is running trx-uhd with
a B100, and seems quite stable.</p>
<p>Moreover, bts 1 trx 0 is running on the i386 and seems happy so
far, after 30 minutes.</p>
<p>This is Limesdr mini.<br>
</p>
<p><br>
</p>
<p>I have just copied the bts0 to trx 0 section from my original
config, duplicated it and changed <br>
</p>
<p>bts0 to bts1, and the ipa unit-id 1805 0, and of course the ip
addresses. <br>
</p>
<p>I will comment the various lines in my configs, as I have
understood them, and look forward to your</p>
<p>comments, or maybe a keyword list explaining what each
parameter is used for.</p>
<br>
<p>! osmo-bsc default configuration<br>
! (assumes STP to run on 127.0.0.1 and uses default point codes)<br>
!<br>
e1_input<br>
e1_line 0 driver ipa<br>
network<br>
network country code 1<br>
mobile network code 1<br>
encryption a5 0<br>
neci 1<br>
paging any use tch 0<br>
handover 0<br>
handover algorithm 1<br>
handover1 window rxlev averaging 10<br>
handover1 window rxqual averaging 1<br>
handover1 window rxlev neighbor averaging 10<br>
handover1 power budget interval 6<br>
handover1 power budget hysteresis 3<br>
handover1 maximum distance 9999<br>
dyn_ts_allow_tch_f 0<br>
periodic location update 30<br>
<b>bts 0</b><b><br>
</b><b> </b> type sysmobts<br>
band DCS1800<br>
cell_identity 0<br>
location_area_code 1<br>
base_station_id_code 63<br>
ms max power 15<br>
cell reselection hysteresis 4<br>
rxlev access min 0<br>
radio-link-timeout 32<br>
channel allocator ascending<br>
rach tx integer 9<br>
rach max transmission 7<br>
channel-descrption attach 1<br>
channel-descrption bs-pa-mfrms 5<br>
channel-descrption bs-ag-blks-res 1<br>
early-classmark-sending forbidden<br>
<b> ip.access unit_id 1801 0</b><b><br>
</b> oml ip.access stream_id 255 line 0<br>
codec-support fr<br>
gprs mode none<br>
trx 0<br>
rf_locked 0<br>
<b> arfcn 871</b><b><br>
</b> nominal power 20<br>
! to use full TRX power, set max_power_red 0<br>
max_power_red 3<br>
rsl e1 tei 0<br>
timeslot 0<br>
phys_chan_config CCCH+SDCCH4<br>
hopping enabled 0<br>
timeslot 1<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 2<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 3<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 4<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 5<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 6<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 7<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
<b>bts 1</b><b><br>
</b><b> </b> type sysmobts<br>
band DCS1800<br>
cell_identity 0<br>
location_area_code 1<br>
base_station_id_code 63<br>
ms max power 15<br>
cell reselection hysteresis 4<br>
rxlev access min 0<br>
radio-link-timeout 32<br>
channel allocator ascending<br>
rach tx integer 9<br>
rach max transmission 7<br>
channel-descrption attach 1<br>
channel-descrption bs-pa-mfrms 5<br>
channel-descrption bs-ag-blks-res 1<br>
early-classmark-sending forbidden<br>
<b> ip.access unit_id 1805 0</b><b><br>
</b> oml ip.access stream_id 255 line 0<br>
codec-support fr<br>
gprs mode none<br>
trx 0<br>
rf_locked 0<br>
<b> arfcn 881</b><b><br>
</b> nominal power 20<br>
! to use full TRX power, set max_power_red 0<br>
max_power_red 3<br>
rsl e1 tei 0<br>
timeslot 0<br>
phys_chan_config CCCH+SDCCH4<br>
hopping enabled 0<br>
timeslot 1<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 2<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 3<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 4<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 5<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 6<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
timeslot 7<br>
phys_chan_config TCH/F<br>
hopping enabled 0<br>
msc 0<br>
no bsc-welcome-text<br>
no bsc-msc-lost-text<br>
no bsc-grace-text<br>
type normal<br>
allow-emergency allow<br>
amr-config 12_2k forbidden<br>
amr-config 10_2k forbidden<br>
amr-config 7_95k forbidden<br>
amr-config 7_40k forbidden<br>
amr-config 6_70k forbidden<br>
amr-config 5_90k allowed<br>
amr-config 5_15k forbidden<br>
amr-config 4_75k forbidden<br>
codec-list fr1 fr2 fr3 hr1 hr3<br>
mgw remote-ip 127.0.0.1<br>
mgw remote-port 2427<br>
mgw local-port 2727<br>
mgw endpoint-range 1 31<br>
bsc<br>
mid-call-timeout 0<br>
no missing-msc-text<br>
</p>
<p>Does this look OK to you??<br>
</p>
<p>Regards,</p>
<p>Gullik<br>
</p>
</blockquote>
</body>
</html>