This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/OpenBSC@lists.osmocom.org/.
Max msuraev at sysmocom.deHi.
I've got following problem while trying to make osmotrx work in multitrx
setting on USRP B210:
sudo chrt 20 ./Transceiver52M/osmo-trx -c 2
sudo chrt 15 ./src/osmo-bts-trx/osmo-bts-trx -t 2 -c
~/.config/osmocom/osmo-bts-mtrx.cfg -d DRTP:DCC:DRSL:DOML:DL1C:DTRX
The bts quits from trx_if.c after checking "if (tcm->critical) {...".
The command sequence seems to be the same for both phy0.0 and phy0.1
However 0.0 one accepts SETTSC command and 0.1 rejects it:
trx_if.c:380 transceiver (phy0.1) rejected TRX command with response:
'RSP SETTSC 1 7'
So far I fail to see where this difference comes from.
Full log:
<0001> oml.c:1249 Initializing OML attribute definitions
<000b> trx_if.c:560 Open transceiver for phy0.0
<000b> trx_if.c:222 Adding new control 'CMD POWEROFF'
<000b> trx_if.c:169 Sending control 'CMD POWEROFF' to phy0.0
<000b> trx_if.c:560 Open transceiver for phy0.1
<000b> trx_if.c:348 Response message: 'RSP POWEROFF 0'
<0001> oml.c:547 Ignoring T200[0] (150 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[1] (180 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[2] (180 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[3] (1680 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[4] (520 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[5] (165 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[6] (1680 ms) as sent by BSC due to
suspected LAPDm bug!
<000b> trx_if.c:222 Adding new control 'CMD POWEROFF'
<000b> trx_if.c:169 Sending control 'CMD POWEROFF' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP POWEROFF 0'
<0001> oml.c:884 ADM state already was Unlocked
<000b> trx_if.c:222 Adding new control 'CMD RXTUNE 1783400'
<000b> trx_if.c:169 Sending control 'CMD RXTUNE 1783400' to phy0.0
<000b> trx_if.c:222 Adding new control 'CMD TXTUNE 1878400'
<000b> trx_if.c:222 Adding new control 'CMD SETTSC 7'
<000b> trx_if.c:222 Adding new control 'CMD POWERON'
<000b> trx_if.c:222 Adding new control 'CMD SETRXGAIN 1'
<000b> trx_if.c:222 Adding new control 'CMD SETPOWER 0'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 0 4'
<0005> paging.c:545 Paging: BS_AG_BLKS_RES = 0 != 1 not fully supported
<000b> trx_if.c:348 Response message: 'RSP RXTUNE 0 1783400'
<000b> trx_if.c:169 Sending control 'CMD TXTUNE 1878400' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP TXTUNE 0 1878400'
<000b> trx_if.c:169 Sending control 'CMD SETTSC 7' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETTSC 0 7'
<000b> trx_if.c:169 Sending control 'CMD POWERON' to phy0.0
<0005> paging.c:545 Paging: BS_AG_BLKS_RES = 0 != 1 not fully supported
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 1 7'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 2 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 3 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 4 13'
<000b> trx_if.c:348 Response message: 'RSP POWERON 0'
<000b> trx_if.c:169 Sending control 'CMD SETRXGAIN 1' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETRXGAIN 0 1'
<000b> trx_if.c:169 Sending control 'CMD SETPOWER 0' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETPOWER 0 0'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 0 4' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 0 4'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 1 7' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 1 7'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 2 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 2 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 3 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 3 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 4 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 4 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 5 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 5 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 5 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 6 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 6 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 6 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 7 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 7 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 7 13'
<0001> oml.c:884 ADM state already was Unlocked
<000b> trx_if.c:222 Adding new control 'CMD RXTUNE 1783800'
<000b> trx_if.c:169 Sending control 'CMD RXTUNE 1783800' to phy0.1
<000b> trx_if.c:222 Adding new control 'CMD TXTUNE 1878800'
<000b> trx_if.c:222 Adding new control 'CMD SETTSC 7'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 0 7'
<000b> trx_if.c:348 Response message: 'RSP RXTUNE 0 1783800'
<000b> trx_if.c:169 Sending control 'CMD TXTUNE 1878800' to phy0.1
<000b> trx_if.c:348 Response message: 'RSP TXTUNE 0 1878800'
<000b> trx_if.c:169 Sending control 'CMD SETTSC 7' to phy0.1
<000b> trx_if.c:348 Response message: 'RSP SETTSC 1 7'
<000b> trx_if.c:380 transceiver (phy0.1) rejected TRX command with
response: 'RSP SETTSC 1 7'
<0001> bts.c:203 Shutting down BTS 0, Reason TRX-CTRL-MSG: CRITICAL
<000b> trx_if.c:222 Adding new control 'CMD POWEROFF'
<000b> trx_if.c:169 Sending control 'CMD POWEROFF' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP POWEROFF 0'
<0001> oml.c:547 Ignoring T200[0] (150 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[1] (180 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[2] (180 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[3] (1680 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[4] (520 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[5] (165 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:547 Ignoring T200[6] (1680 ms) as sent by BSC due to
suspected LAPDm bug!
<0001> oml.c:884 ADM state already was Unlocked
<000b> trx_if.c:222 Adding new control 'CMD POWERON'
<000b> trx_if.c:169 Sending control 'CMD POWERON' to phy0.0
<000b> trx_if.c:222 Adding new control 'CMD SETRXGAIN 1'
<000b> trx_if.c:222 Adding new control 'CMD SETPOWER 0'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 0 4'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 1 7'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 2 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 3 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 4 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 5 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 6 13'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 7 13'
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<000b> trx_if.c:348 Response message: 'RSP POWERON 0'
<000b> trx_if.c:169 Sending control 'CMD SETRXGAIN 1' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETRXGAIN 0 1'
<000b> trx_if.c:169 Sending control 'CMD SETPOWER 0' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETPOWER 0 0'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 0 4' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 0 4'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 1 7' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 1 7'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 2 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 2 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 3 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 3 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 4 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 4 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 5 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 5 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 6 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 6 13'
<000b> trx_if.c:169 Sending control 'CMD SETSLOT 7 13' to phy0.0
<000b> trx_if.c:348 Response message: 'RSP SETSLOT 0 7 13'
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 0 7'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 1 1'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 2 1'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 3 1'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 4 1'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 5 1'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 6 1'
<000b> trx_if.c:222 Adding new control 'CMD SETSLOT 7 1'
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<0001> oml.c:884 ADM state already was Unlocked
<000b> trx_if.c:138 Clock indication: fn=999376
<000b> trx_if.c:470 TX burst tn=0 fn=999396 pwr=0
<000b> trx_if.c:470 TX burst tn=1 fn=999396 pwr=0
<000b> trx_if.c:470 TX burst tn=2 fn=999396 pwr=0
...
--
Max Suraev <msuraev at sysmocom.de> http://www.sysmocom.de/
=======================================================================
* sysmocom - systems for mobile communications GmbH
* Alt-Moabit 93
* 10559 Berlin, Germany
* Sitz / Registered office: Berlin, HRB 134158 B
* Geschaeftsfuehrer / Managing Director: Harald Welte