This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/baseband-devel@lists.osmocom.org/.
baymax Robo baymax254 at gmail.comOh okay. The headphone jack is working fine, i have tested it. And helloworld isn't working. Can you tell some other method to test phones connectivity with my system. On Thu, Jun 1, 2017 at 12:16 PM, Anton Gorbachev <antgorka at gmail.com> wrote: > Hi, > > Check the picture > https://osmocom.org/attachments/download/2091/ > motorola_c123_hello_world.jpg > > I mean the outer plastic case of the phone may not allow your jack to be > inserted at the whole length to thoe whole even if it looks like OK. > It depends on your jack case shape. > > KR, > Anton > > 2017-06-01 9:57 GMT+03:00 baymax Robo <baymax254 at gmail.com>: > >> Hi, >> >> Thanks for replying back. >> >> I am not using virtualized environment. No success with minicom test. >> What exactly do you mean by jack is being plugged on the whole length, i >> didn't get it. >> >> >> On Thu, Jun 1, 2017 at 11:16 AM, Anton Gorbachev <antgorka at gmail.com> >> wrote: >> >>> Hi, >>> >>> Are you sure the jack is being plugged on the whole length? >>> Did you get success with minicom test? >>> I would recommend you to disassemble phone and check whether the jack >>> plugged an the whole length. >>> Do you use virtualized OS or normal? If virtualized, try to play with >>> the settings. >>> >>> KR, >>> Anton >>> >>> 2017-06-01 7:30 GMT+03:00 baymax Robo <baymax254 at gmail.com>: >>> >>>> Hi, >>>> >>>> I am trying to write osmocombb to Motorolla c118 phone by following the >>>> given [1] guide.I have successfully compiled firmware binaries but having >>>> issues while writing them to phone. >>>> >>>> I connected motorolla c118 via USB Serial To RS232 TTL to 2.5mm audio >>>> jack, using the given guide [2] >>>> >>>> When I run this command >>>> >>>> $ dmesg | grep tty >>>> >>>> I get the following output >>>> >>>> [ 0.000000] console [tty0] enabled >>>> [ 14.946936] usb 3-6: pl2303 converter now attached to ttyUSB0 >>>> [ 973.747957] pl2303 ttyUSB0: pl2303 converter now disconnected from >>>> ttyUSB0 >>>> [ 1484.595816] usb 3-6: pl2303 converter now attached to ttyUSB0 >>>> [ 1845.344494] pl2303 ttyUSB0: pl2303 converter now disconnected from >>>> ttyUSB0 >>>> [ 2643.566407] usb 3-6: pl2303 converter now attached to ttyUSB1 >>>> >>>> And on running this >>>> >>>> $ sudo cu -l /dev/ttyUSB1 -s 115200 >>>> >>>> I get a connected message but no further progress is done. When i press >>>> Power button briefly, no activity is shown. I have tried with two phones >>>> but no success on any. I have checked the connectivity between headphone >>>> jack and USB serial chip via voltmeter, it is fine as well. Also tried by >>>> doing Master reset on phone but no use. What can be issue and how can i fix >>>> it. ? >>>> >>>> Kindly ignore any mistakes, i am new to this domain, couldn't find much >>>> help on google as well :( >>>> >>>> [1] >>>> https://osmocom.org/projects/baseband/wiki/Software_Getting_Started >>>> https://osmocom.org/projects/baseband/wiki/Osmocon >>>> >>>> [2] >>>> http://www.linuxx.eu/2014/09/osmocombb-hardware-and-software-setup.html >>>> >>>> [2] >>>> >>>> >>> >> > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.osmocom.org/pipermail/baseband-devel/attachments/20170601/111dea70/attachment.htm>