This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/baseband-devel@lists.osmocom.org/.
Tomas Kopsa deacon at volny.czHi Lia, I have tested another cable (USB <-> 2,5 jack, speacial for Compal phones) - it is the same chip (Prolific) and I am able to load firmware too. Although it is the same chip, there is a difference that this one makes the osmocon printing those messages instantly when phone is not connected: got 1 bytes from modem, data looks like: f5 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: f5 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: f5 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: fd . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: f5 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: fd . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: ea . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: ea . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: ea . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: ea . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: fd . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: ea If I connect phone, printing stops. Here is what happened when I tried to load firmware without xor (-m c123) and pressed the button: (This happened every attempt without xor flag) Received PROMPT2 from phone, starting download handle_write(): 1087 bytes (1087/50947) got 1 bytes from modem, data looks like: 1b . got 1 bytes from modem, data looks like: f6 . got 1 bytes from modem, data looks like: 02 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: 45 E got 1 bytes from modem, data looks like: 53 S got 1 bytes from modem, data looks like: 16 . Received DOWNLOAD NACK from phone, something went wrong :( got 1 bytes from modem, data looks like: 66 f got 1 bytes from modem, data looks like: 74 t got 1 bytes from modem, data looks like: 6d m got 1 bytes from modem, data looks like: 74 t got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 6c l Received FTMTOOL from phone, ramloader has aborted got 1 bytes from modem, data looks like: 65 e got 1 bytes from modem, data looks like: 72 r got 1 bytes from modem, data looks like: 72 r got 1 bytes from modem, data looks like: 6f o got 1 bytes from modem, data looks like: 72 r got 1 bytes from modem, data looks like: 00 . If you have USB adapter (I guess you have), you dont need to check model, check 'lsusb' [root at amilo osmocon]# lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub *Bus 002 Device 017: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port* If you have Prolific, which is very common, I encourage you to use xor flag. You can also try to switch on your phone to check if original firmware boots. I experienced during my early tests, that phone crashed (probably SRAM) and it was unable to boot even original fw. In case phone is crashed, reconnect battery and it will fix itself. Here is the ACK after hello world load: handle_write(): 768 bytes (17919/19787) handle_write(): 768 bytes (18687/19787) handle_write(): 768 bytes (19455/19787) handle_write(): 332 bytes (19787/19787) handle_write(): finished got 1 bytes from modem, data looks like: 1b . got 1 bytes from modem, data looks like: f6 . got 1 bytes from modem, data looks like: 02 . got 1 bytes from modem, data looks like: 00 . got 1 bytes from modem, data looks like: 41 A got 1 bytes from modem, data looks like: 03 . got 1 bytes from modem, data looks like: 42 B Received DOWNLOAD ACK from phone, your code is running now! OSMOCOM Hello World (revision osmocon_v0.0.0-754-gb5abcb6-modified) ====================================================================== Device ID code: 0xb4fb Device Version code: 0x0000 ARM ID code: 0xfff3 cDSP ID code: 0x0128 Die ID code: efce3b1ce1001255 ====================================================================== REG_DPLL=0x2413 CNTL_ARM_CLK=0xf0a1 CNTL_CLK=0xff91 CNTL_RST=0xfff3 CNTL_ARM_DIV=0xfff9 ============================================== Looking forward your response, Tomas > Hi Tomas, > > thanks for your feedback. > > Actually, I've tried both flags (woth/without xor extension), but hte > result is the same. > > So, in your opinioni, the problem could depend on the cable? > > I don't have the cable model now, but I can send you this information > Tuesday. > > Thanks again. > > cheers. > > lia > > ----Messaggio originale---- > Da: deacon at volny.cz > Data: 16-gen-2011 4.26 > A: <list_mailing at libero.it> > ubut Ogg: Re: C115 loader.compalram.bin > > Hello, > I have C115 too and I use '-m c123xor' switch, the phone mostly > boots on 1st button push (I never reacher full load with '-m c123'). > > ./osmocon -p /dev/ttyUSB0 -m c123xor > ../../target/firmware/board/compal_e88/hello_world.compalram.bin > ./osmocon -p /dev/ttyUSB0 -m c123xor > ../../target/firmware/board/compal_e88/loader.compalram.bin > ./osmocon -p /dev/ttyUSB0 -m c123xor > ../../target/firmware/board/compal_e88/layer1.compalram.bin > > I have FTDI USB<->RS232 + Calypso serial. When load fails (with > xor), I have a feeling that it helps reconnection cable to the phone. > (I have also Calypso USB cable which I haven't tested yet, will > report later.) > > - Tomas > > >>> Hello. >>> I'm trying to load the loader.compalram.bin. >>> The behaviour is very strange because sometimes the download is complete and >>> successfull, sometimes; in particular, in this case, the download is complete, >>> but any ACK is sent back from the mobile phone (see below). >>> ./osmocon -p /dev/ttyUSB0 -m c123 ../.. >>> /target/firmware/board/compal_e99/loader.compalram.bin >>> got 2 bytes from modem, data looks like: 2e c8 .. >>> got 5 bytes from modem, data looks like: 1b f6 02 00 41 ....A >>> got 1 bytes from modem, data looks like: 01 . >>> got 1 bytes from modem, data looks like: 40 @ >>> Received PROMPT1 from phone, responding with CMD >>> read_file(../../target/firmware/board/compal_e99/loader.compalram.bin): >>> file_size=21752, hdr_len=4, dnload_len=21759 >>> got 1 bytes from modem, data looks like: 1b . >>> got 1 bytes from modem, data looks like: f6 . >>> got 1 bytes from modem, data looks like: 02 . >>> got 1 bytes from modem, data looks like: 00 . >>> got 1 bytes from modem, data looks like: 41 A >>> got 1 bytes from modem, data looks like: 02 . >>> got 1 bytes from modem, data looks like: 43 C >>> Received PROMPT2 from phone, starting download >>> handle_write(): 4096 bytes (4096/21759) >>> handle_write(): 4096 bytes (8192/21759) >>> handle_write(): 4096 bytes (12288/21759) >>> handle_write(): 4096 bytes (16384/21759) >>> handle_write(): 4096 bytes (20480/21759) >>> handle_write(): 1279 bytes (21759/21759) >>> handle_write(): finished >>> >>> >>> The target phone is C115. I tried compal_exx and the result is the same :-( >>> >>> Please, can someone help me to understand the reasons? >>> Thanks in advance. >>> >>> >>> >>> >> > > > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.osmocom.org/pipermail/baseband-devel/attachments/20110117/a10d1974/attachment.htm>