This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/baseband-devel@lists.osmocom.org/.
Nicolas Bareil nico at chdir.orgHello, I try to use the 'host23/mobile' application on a C123 but without success. I followed Steve's instructions[1] with today's git tree (d95eddad): 1. osmocon -p /dev/ttyS0 -m c123xor layer1.compalram.bin 2. ./host/layer23/src/mobile/mobile 3. Power on the phone (output of theses commands is thereafter) But I'm not sure it really works: the firmware seems to freeze (not responding to the power button anymore) and the last output of 'mobile' is: <0003> gsm322.c:257 Sync to ARFCN=104 rxlev=-65 (No sysinfo yet, ccch mode NONE) Based on the low rxlevel, I guess it is not acquiring any meaningful signal? In [2], Steve said the internal antenna was switched off when the cable is plugged in, is it still true? I tried to RTFM but I am stuck here. Thanks for your patience, Footnotes: [1] http://baseband-devel.722152.n3.nabble.com/Running-osmocombb-on-a-Motorol-C118-tp937345p937416.html [2] http://lists.osmocom.org/pipermail/baseband-devel/2010-May/000435.html ,---- | % osmocon -p /dev/ttyS0 -m c123xor layer1.compalram.bin | ... | Received DOWNLOAD ACK from phone, your code is running now! | | OSMOCOM Layer 1 (revision osmocon_v0.0.0-598-gd95edda) | ====================================================================== | Device ID code: 0xb4fb | Device Version code: 0x0000 | ARM ID code: 0xfff3 | cDSP ID code: 0x0128 | Die ID code: ebd8283cba021198 | ====================================================================== | REG_DPLL=0x2413 | CNTL_ARM_CLK=0xf0a1 | CNTL_CLK=0xff91 | CNTL_RST=0xfff3 | CNTL_ARM_DIV=0xfff9 | ====================================================================== | | THIS FIRMWARE WAS COMPILED WITHOUT TX SUPPORT!!! | Assert DSP into Reset | Releasing DSP from Reset | Setting some dsp_api.ndb values | Setting API NDB parameters | DSP Download Status: 0x0001 | DSP API Version: 0x0000 0x0000 | Finishing download phase | DSP Download Status: 0x0002 | DSP API Version: 0x3606 0x0000 | LOST 7478! | L1CTL_RESET_REQ: FULL!L1CTL_PM_REQ start=0 end=124 | PM MEAS: ARFCN=0, 27 dBm at baseband, -110 dBm at RF | PM MEAS: ARFCN=0, 26 dBm at baseband, -112 dBm at RF | PM MEAS: ARFCN=1, 30 dBm at baseband, -107 dBm at RF | PM MEAS: ARFCN=2, 29 dBm at baseband, -108 dBm at RF | PM MEAS: ARFCN=3, 43 dBm at baseband, -94 dBm at RF | PM MEAS: ARFCN=4, 32 dBm at baseband, -105 dBm at RF | ../.. | PM MEAS: ARFCN=1023, 33 dBm at baseband, -104 dBm at RF | L1CTL_RESET_REQ: FULL!L1CTL_FBSB_REQ (arfcn=104, flags=0x7) | Starting FCCH RecognitionFB0 (1748:10): TOA=11712, Power=-106dBm, Angle=-22058Hz | FB0 (1775:11): TOA=12528, Power= -65dBm, Angle=-3818Hz | FB0 (1796:5): TOA= 5280, Power= -68dBm, Angle=-16117Hz | FB0 (1799:1): TOA= 96, Power=-109dBm, Angle= 7082Hz `---- ,---- | % ./host/layer23/src/mobile/mobile | ... | Failed to connect to '/tmp/osmocom_sap'. | Failed during sap_open(), no SIM reader | <000e> sim.c:1206 init SIM client | <0005> gsm48_cc.c:61 init Call Control | <0001> gsm48_rr.c:5330 init Radio Ressource process | <0004> gsm48_mm.c:1220 init Mobility Management process | <0004> gsm48_mm.c:971 Selecting PLMN SEARCH state, because no SIM. | <0002> gsm322.c:3466 init PLMN process | <0003> gsm322.c:3467 init Cell Selection process | <0003> gsm322.c:3521 No stored BA list | VTY available on port 4247. | Mobile initialized, please start phone now! | <0002> gsm322.c:3093 (ms 1) Event 'EVENT_SWITCH_ON' for automatic PLMN selection in state 'A0 null' | <000d> gsm322.c:1055 SIM is removed | <0002> gsm322.c:1056 SIM is removed | <0002> gsm322.c:511 new state 'A0 null' -> 'A6 no SIM inserted' | <0003> gsm322.c:3313 (ms 1) Event 'EVENT_SWITCH_ON' for Cell selection in state 'C0 null' | <0003> gsm322.c:2986 Switch on without SIM. | <0003> gsm322.c:540 new state 'C0 null' -> 'C6 any cell selection' | <0003> gsm322.c:2404 Getting PM for frequency 0 twice. Overwriting the first! Please fix prim_pm.c | <0003> gsm322.c:2415 Found signal (frequency 3 rxlev -94 (16)) | <0003> gsm322.c:2415 Found signal (frequency 8 rxlev -86 (24)) | <0003> gsm322.c:2415 Found signal (frequency 16 rxlev -93 (17)) | ... | <0003> gsm322.c:2415 Found signal (frequency 819 rxlev -97 (13)) | <0003> gsm322.c:2404 Getting PM for frequency 955 twice. Overwriting the first! Please fix prim_pm.c | <0003> gsm322.c:2415 Found signal (frequency 982 rxlev -98 (12)) | ... | <0003> gsm322.c:2415 Found signal (frequency 1004 rxlev -91 (19)) | <0003> gsm322.c:2415 Found signal (frequency 1007 rxlev -89 (21)) | <0003> gsm322.c:2415 Found signal (frequency 1009 rxlev -97 (13)) | <0003> gsm322.c:2415 Found signal (frequency 1010 rxlev -86 (24)) | <0003> gsm322.c:2415 Found signal (frequency 1011 rxlev -67 (43)) | <0003> gsm322.c:2415 Found signal (frequency 1012 rxlev -86 (24)) | <0003> gsm322.c:2415 Found signal (frequency 1013 rxlev -80 (30)) | <0003> gsm322.c:2415 Found signal (frequency 1014 rxlev -87 (23)) | <0003> gsm322.c:2415 Found signal (frequency 1021 rxlev -82 (28)) | <0003> gsm322.c:2415 Found signal (frequency 1022 rxlev -98 (12)) | <0003> gsm322.c:2348 Found 97 frequencies. | <0003> gsm322.c:257 Sync to ARFCN=104 rxlev=-65 (No sysinfo yet, ccch mode NONE) `----