This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/UmTRX@lists.osmocom.org/.
Alexander Chemeris alexander.chemeris at gmail.comJijo, In osmo-bts config you always specify "bts 0". If you need several BTS on the same PC, use different config files for them. You can pass a config file name with a command line option to osmo-bts. All BTS must have different ipa unit-id - that's how they are differentiated in osmo-nitb (openbsc) configuration. On Thu, May 21, 2015 at 11:48 AM, Andy Avtushenko <andy.avtushenko at gmail.com> wrote: > Hi Jijo. > Could you please send openbsc.cfg > also you can use "locate" to find a logs. > run something like > locate osmo-trx either locate current > > > 2015-05-21 4:47 GMT-08:00 Joe Ge <jijo123789 at gmail.com>: >> >> Hi Andy, >> >> That setup seemed to have worked for me once I rebuilt it again. >> But I'm still facing the same error as stated by Amber & Sarosh >> The 2nd BTS refuses to take the configuration of "bts 1". I have tried to >> run the 2nd BTS on the same machine as well as from a networked machine. >> >> >> ------------------------------------------------------------------------------------------ >> root at nistws4:/home/nist-ws4# osmobts-trx -c /root/.osmocom/ho_bts1.cfg >> ((*)) >> | >> / \ OsmoBTS >> Using MAC address of eth0: '40:a8:f0:63:c7:b6' >> <0006> scheduler.c:212 Init scheduler for trx=0 >> <000b> trx_if.c:493 Open transceiver for trx=0 >> <000b> trx_if.c:504 Waiting for transceiver send clock >> There is no such command. >> Error occurred during reading below line: >> band DCS1800 >> >> % Unknown BTS number 1 (num 1) >> Failed to parse the config file: '/root/.osmocom/ho_bts1.cfg' >> >> ------------------------------------------------------------------------------------------ >> >> >> >> Configuration file for ho_bts1.cfg is as follows: >> >> ------------------------------------------------------------------------------------------ >> bts 1 >> band DCS1800 >> ipa unit-id 1802 0 >> oml remote-ip 172.30.1.10 >> rtp bind-ip 172.30.1.10 >> rtp jitter-buffer 0 >> paging lifetime 0 >> gsmtap-sapi bcch >> gsmtap-sapi ccch >> gsmtap-sapi rach >> gsmtap-sapi agch >> gsmtap-sapi pch >> gsmtap-sapi sdcch >> gsmtap-sapi pacch >> gsmtap-sapi pdtch >> gsmtap-sapi sacch >> fn-advance 20 >> ms-power-loop -60 >> timing-advance-loop >> trx 0 >> rxgain 0 >> power 0 >> >> ------------------------------------------------------------------------------------------ >> >> >> Can you please suggest some alternatives? >> >> Thanks and Regards, >> Jijo >> >> On Thu, May 21, 2015 at 12:06 PM, Joe Ge <jijo123789 at gmail.com> wrote: >>> >>> Hi Andy, >>> >>> There are no logs in the location you specified. >>> Does it need to be activated somehow(debug mode)??? >>> What might be the problem? >>> >>> Regards, >>> Jijo >>> >>> On Wed, May 20, 2015 at 9:29 PM, Andy Avtushenko >>> <andy.avtushenko at gmail.com> wrote: >>>> >>>> Hello Jijo >>>> Could you please provide us a osmo-trx logs >>>> located in var/logs/osmo-trx/current >>>> thanks >>>> >>>> 2015-05-20 4:34 GMT-08:00 Jijo <jijo123789 at gmail.com>: >>>>> >>>>> Hi Alexander, >>>>> >>>>> I'm working on a similar setup as Amber & Sarosh, till about recently I >>>>> was >>>>> facing the same error as these guys (where the config file was not >>>>> parsing >>>>> the trx 1 and later sections) when I stumbled upon your response. >>>>> Now I've installed the same versions as suggested by you : >>>>> osmo_trx: fairwaves/master >>>>> libosmocore: master >>>>> libosmo-abis: fairwaves/master >>>>> libsmpp34: master >>>>> osmo_bts: fairwaves/debian >>>>> openbsc: fairwaves/master >>>>> >>>>> But somehow my osmobts-trx is not recognizing osmo-trx >>>>> >>>>> -------------------------------------------------------- >>>>> <0001> oml.c:419 L3=0x94eb07e, VAL=0x94eb0ad, DIF=47 >>>>> <0001> oml.c:790 ADM state already was Unlocked >>>>> <0001> oml.c:790 ADM state already was Unlocked >>>>> <0001> oml.c:790 ADM state already was Unlocked >>>>> <0001> oml.c:790 ADM state already was Unlocked >>>>> <000b> trx_if.c:187 No response from transceiver for trx=0 >>>>> <000b> trx_if.c:187 No response from transceiver for trx=0 >>>>> <000b> trx_if.c:187 No response from transceiver for trx=0 >>>>> <000b> trx_if.c:187 No response from transceiver for trx=0 >>>>> -------------------------------------------------------- >>>>> >>>>> I'm using UmDESK for this setup. >>>>> PS- I built osmo-bts with(./configure --enable-trx). I hope that was >>>>> correct >>>>> for UmDESK >>>>> Can you help with this regard? >>>>> >>>>> Thanks and Regards, >>>>> Jijo >>>>> >>>>> >>>>> >>>> >>>> >>>> >>>> -- >>>> Best regards, >>>> Andy >>> >>> >> > > > > -- > Best regards, > Andy -- Regards, Alexander Chemeris. CEO, Fairwaves, Inc. https://fairwaves.co