This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/UmTRX@lists.osmocom.org/.
Andrey Sviyazov andrey.sviyazov at fairwaves.ruSergey. I'll play around GPS power and RTC supply, thank you for your help. Thomas. About r0x16 please be sure that sometimes it isn't set to default value after power up (I saw it few times). Also I think that possible those bad "power on reset" gave us unstable result of LMS autocalibration. Best regards, Andrey Sviyazov. 2012/7/19 sergey kostanbaev <sergey.kostanbaev at gmail.com> > Which gives ~1.5khz cut-off, that's strange > > Also I'd check GPS VDD and AVDD nosies > > > On Thu, Jul 19, 2012 at 6:41 PM, Andrey Sviyazov < > andrey.sviyazov at fairwaves.ru> wrote: > >> 1kOhm resistor and 0.1uF capacitor already exist between DAC and VC input. >> Of course I'll increase capacitance or resistance to be sure about VC pin. >> >> Best regards, >> Andrey Sviyazov. >> >> >> >> 2012/7/19 sergey kostanbaev <sergey.kostanbaev at gmail.com> >> >>> No :) But it may cause. >>> >>> I'd check all the line from FPGA to DAC to VCTXCO because VC pin is >>> really sensible to any noise. >>> - caused by power supply of DAC. >>> - output noise of DAC. >>> - algorithm of changing values >>> >>> At first I'd inspect VC pin at VCTXCO and try to filter it with cut-off >>> frequency 1-0.1 Hz >>> >>> >>> On Thu, Jul 19, 2012 at 6:29 PM, Andrey Sviyazov < >>> andrey.sviyazov at fairwaves.ru> wrote: >>> >>>> Sergey. >>>> Is it really so frequently (32k/s updates at 1pps reference)? >>>> >>>> Best regards, >>>> Andrey Sviyazov. >>>> >>>> >>>> >>>> 2012/7/19 sergey kostanbaev <sergey.kostanbaev at gmail.com> >>>> >>>>> >>>>> >>>>> On Thu, Jul 19, 2012 at 6:10 PM, Andrey Sviyazov < >>>>> andrey.sviyazov at fairwaves.ru> wrote: >>>>> >>>>>> Hi all. >>>>>> >>>>>> I've found spurs on the LO noise plot at ~33kHz and ~66kHz offset >>>>>> when GPS antenna used and position locked. >>>>>> This spurs begin grow up when GPS just near to lock position and >>>>>> after locking spurs stopped to grow as you can see at picture. >>>>>> If thereafter GPS disconnected then noise coming back to normal plot. >>>>>> I think that it is result of 32768Hz clock in the GPS module EB-230, >>>>>> but can't understant how it can impact to 26MHz clock or VCO. >>>>>> >>>>> >>>>> As another idea it can be caused by continues GPS correction lead to >>>>> DAC changes to the VCTXCO. >>>>> >>>>> >>>>>> Please tell me something who know. >>>>>> >>>>>> Thomas. >>>>>> Was GPS antenna connected when noise measured like on the picture >>>>>> which you sent us (also attached here)? >>>>>> I would to know because of anomal peak near to 30kHz offset too. >>>>>> >>>>>> Best regards, >>>>>> Andrey Sviyazov. >>>>>> >>>>>> >>>>>> >>>>>> 2012/7/19 Andrey Sviyazov <andrey.sviyazov at fairwaves.ru> >>>>>> >>>>>>> Sorry, that was meant to be sent to the mailing list :) >>>>>>> >>>>>>> Best regards, >>>>>>> Andrey Sviyazov. >>>>>>> >>>>>>> ---------- Forwarded message ---------- >>>>>>> From: Andrey Sviyazov <andreysviyaz at gmail.com> >>>>>>> Date: 2012/7/18 >>>>>>> Subject: LMS TxLO noise >>>>>>> >>>>>>> Hi Thomas. >>>>>>> >>>>>>> Here forwarded my last e-mail with noise plots when I stopped work >>>>>>> around it at first time, please see below. >>>>>>> >>>>>>> Please try to play around Tx PLL charge pump current (register 0x16) >>>>>>> for better RMS phase stability. >>>>>>> I think we should reach 1 degree or below. >>>>>>> >>>>>>> Alexander gave me the second UmTRX board and after checking and >>>>>>> fixing all known hardware issues<http://code.google.com/p/umtrx/issues/list?can=1&q=&colspec=ID+Type+Status+Priority+Milestone+Owner+Summary+Modified&cells=tiles>I've got roughly the same LO noise plot. >>>>>>> Possible Robin had no time to fixing all of our issues, so check >>>>>>> them all please. >>>>>>> And also check please what type of TCXO installed on your board. >>>>>>> >>>>>>> Best regards, >>>>>>> Andrey Sviyazov. >>>>>>> >>>>>>> ---------- Forwarded message ---------- >>>>>>> From: Andrey Sviyazov <andreysviyaz at gmail.com> >>>>>>> Date: 2012/4/13 >>>>>>> Subject: Re: LMS TxLO noise >>>>>>> >>>>>>> Hi all. >>>>>>> >>>>>>> There is progress with LMS PLL :) >>>>>>> Pictures are attached here. >>>>>>> t was discovered that 80 kHz spurs come from Ethernet, or rather >>>>>>> from the ET1011. >>>>>>> I unknowingly put the choke between transistor of 1V regulator and >>>>>>> analog power 1V. >>>>>>> As a result, the regulator has become unstable and oscillated 80 kHz >>>>>>> with amplitude of 200 mV, which climbed into the LMS PLL. >>>>>>> To correct this problem L46 should be replaced by jumper on all alfa >>>>>>> version PCB's. >>>>>>> >>>>>>> Also I just played with current in the PLL loop, shown on the >>>>>>> picture for clarity. >>>>>>> Proved to be the optimal current 1,9 mA (you should write 0x93 in >>>>>>> the register of 0x16). >>>>>>> But, I think, for the RxPLL will be better use of the current 2.4 >>>>>>> mA, because the nearest noises more important for Rx (you should write 0x98 >>>>>>> in the register 0x26). >>>>>>> >>>>>>> Best regards, >>>>>>> Andrey Sviyazov. >>>>>>> >>>>>>> >>>>>>> >>>>>> >>>>> >>>> >>> >> > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.osmocom.org/pipermail/umtrx/attachments/20120719/0fd6086d/attachment-0001.htm>