This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/OpenBSC@lists.osmocom.org/.
Sergey V. Efimov risky at mail.ruHello, I used step-by-step instruction from the osmocom.org site. Here is my openbsc config: ==== e1_input e1_line 0 driver ipa network network country code 250 mobile network code 77 short name ABC long name ABC auth policy accept-all location updating reject cause 13 encryption a5 0 neci 1 rrlp mode none mm info 1 handover 0 handover window rxlev averaging 10 handover window rxqual averaging 1 handover window rxlev neighbor averaging 10 handover power budget interval 6 handover power budget hysteresis 3 handover maximum distance 9999 timer t3101 10 timer t3103 0 timer t3105 0 timer t3107 0 timer t3109 4 timer t3111 0 timer t3113 60 timer t3115 0 timer t3117 0 timer t3119 0 timer t3141 0 bts 0 type nanobts band DCS1800 cell_identity 0 location_area_code 1 training_sequence_code 7 base_station_id_code 63 ms max power 15 cell reselection hysteresis 4 rxlev access min 0 channel allocator ascending rach tx integer 9 rach max transmission 7 ip.access unit_id 1234 0 oml ip.access stream_id 255 line 0 gprs mode gprs gprs routing area 0 gprs cell bvci 2 gprs nsei 101 gprs nsvc 0 nsvci 101 gprs nsvc 0 local udp port 23000 gprs nsvc 0 remote udp port 23000 gprs nsvc 0 remote ip 192.168.168.98 trx 0 rf_locked 0 arfcn 666 nominal power 23 max_power_red 20 rsl e1 tei 0 timeslot 0 phys_chan_config CCCH+SDCCH4 timeslot 1 phys_chan_config PDCH timeslot 2 phys_chan_config PDCH timeslot 3 phys_chan_config TCH/F timeslot 4 phys_chan_config TCH/F timeslot 5 phys_chan_config TCH/F timeslot 6 phys_chan_config TCH/F timeslot 7 phys_chan_config TCH/F ==== Here is my osmo-sgsn.cfg ==== sgsn gtp local-ip 192.168.168.98 ggsn 0 remote-ip 192.168.168.230 ggsn 0 gtp-version 1 ! ns timer tns-block 3 timer tns-block-retries 3 timer tns-reset 3 timer tns-reset-retries 3 timer tns-test 30 timer tns-alive 3 timer tns-alive-retries 10 encapsulation udp local-ip 192.168.168.98 encapsulation udp local-port 23000 encapsulation framerelay-gre enabled 0 ==== Here is my ggsn.cfg === listen 192.168.168.230 net 192.168.168.0/24 dynip 192.168.168.240/30 === Here is my open-bts.cfg === bts 0 band 1800 ipa unit-id 1234 0 oml remote-ip 192.168.168.98 === Regards, Sergey. On Aug 14, 2013, at 8:17 PM, Holger Hans Peter Freyther wrote: > On Wed, Aug 14, 2013 at 07:42:30PM +0400, Sergey V. Efimov wrote: >> Hello All, >> >> <0011> gprs_bssgp.c:1000 NSEI=101/BVCI=2 Rejecting PDU type 1 for unknown BVCI >> <0011> gprs_bssgp_util.c:103 BSSGP BVCI=0 Tx STATUS, cause=Unknown BVCI >> <0011> gprs_bssgp.c:1000 NSEI=101/BVCI=2 Rejecting PDU type 1 for unknown BVCI >> <0011> gprs_bssgp_util.c:103 BSSGP BVCI=0 Tx STATUS, cause=Unknown BVCI > > without your NITB/BSC config it is difficult to judge. What doesn't work for > sure is to restart the SGSN once the PCU has exchanged some messages with it. > > > holger > >