This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/gerrit-log@lists.osmocom.org/.
pespin gerrit-no-reply at lists.osmocom.orgpespin has posted comments on this change. ( https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502 ) Change subject: add common/chapters/cs7-config ...................................................................... Patch Set 1: Code-Review+1 (6 comments) https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502/1/common/chapters/cs7-config.adoc File common/chapters/cs7-config.adoc: https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502/1/common/chapters/cs7-config.adoc@63 PS1, Line 63: # IP address of the remote STP: We usually do use some kind of markers for this. It shows up in the pdf as (1) and then below the explanation. It'd be great also adding a line with "local-ip" (or however it's called) and stating it's optional, kernel deciding by default. https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502/1/common/chapters/cs7-config.adoc@103 PS1, Line 103: Each CNI program on an SCCP/M3UA link typically has a local point-code, That's a bit strange from reader point of view. You first explain the different formats supported and then you explained what you already showed through the format. I'd make a lot more sense to first have the "Local Point-Code" section and perhaps also de "Remote Point-Code" one, and later the "Point-Code Format" one, which is basically a detailed explanation on how to set them. https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502/1/common/chapters/cs7-config.adoc@138 PS1, Line 138: sccp-address my-entry my-entry-name? or my-entry-label https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502/1/common/chapters/cs7-config.adoc@185 PS1, Line 185: An `asp` is part of an `as`. For details, see the OsmoSTP manual, chapters Not necessarily, an ASP can be used by several AS afair. So let's say the relation is not "AS 1 --- * ASP". That's why in VTY config the asp node is not inside the AS one, but separated, and only a reference to the ASP is used inside the AS node. https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502/1/common/chapters/cs7-config.adoc@189 PS1, Line 189: an `as` references the `asp` belonging to it by their names. In typical usage, In typical simple/minimal setup We support now running with several ASPs per AS, for instance using traffic-node loadshare https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502/1/common/chapters/cs7-config.adoc@204 PS1, Line 204: It is possible to configure only an `as` or only an `asp` explicitly -- a I'm not sure to understand this part here. I think you should simplymake clear before hand that AS*---*ASP and they must be linked, and you can then drop completely these paragraphs below. -- To view, visit https://gerrit.osmocom.org/c/osmo-gsm-manuals/+/17502 To unsubscribe, or for help writing mail filters, visit https://gerrit.osmocom.org/settings Gerrit-Project: osmo-gsm-manuals Gerrit-Branch: master Gerrit-Change-Id: Ia2508d4c7b0fef9cdc57e7e122799a480e340bf7 Gerrit-Change-Number: 17502 Gerrit-PatchSet: 1 Gerrit-Owner: neels <nhofmeyr at sysmocom.de> Gerrit-Reviewer: Jenkins Builder Gerrit-Reviewer: pespin <pespin at sysmocom.de> Gerrit-Comment-Date: Wed, 18 Mar 2020 11:56:44 +0000 Gerrit-HasComments: Yes Gerrit-Has-Labels: Yes Gerrit-MessageType: comment -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.osmocom.org/pipermail/gerrit-log/attachments/20200318/4967fe69/attachment.htm>