This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/gerrit-log@lists.osmocom.org/.
Kévin Redon gerrit-no-reply at lists.osmocom.orgKévin Redon has uploaded this change for review. ( https://gerrit.osmocom.org/12516 Change subject: add README file ...................................................................... add README file this describes the project, how to compile, and how to flash the USB DFU bootloader Change-Id: If884bca373aab10fe74d16f42b79dd6685eeabcf --- A README 1 file changed, 50 insertions(+), 0 deletions(-) git pull ssh://gerrit.osmocom.org:29418/osmo-asf4-dfu refs/changes/16/12516/1 diff --git a/README b/README new file mode 100644 index 0000000..031bc27 --- /dev/null +++ b/README @@ -0,0 +1,50 @@ +This is an implementation of the DFU mode of the [USB DFU Device Class Specification](https://usb.org/document-library/device-firmware-upgrade-11-new-version-31-aug-2004) for the Microchip SAM D5x/E5x micro-controller. +It is meant to be used as bootloader to allow flashing the main application over USB. + +The code has been developed for the Microchip [SAM E54 Xplained Pro](https://www.microchip.com/DevelopmentTools/ProductDetails/PartNo/ATSAME54-XPRO) development board using a [SAM E54](https://www.microchip.com/wwwproducts/en/ATSAME54P20A) micro-controller. +It should work on any chip of the SAM D5x/E5x device family by replacing the corresponding device-specific definitions (usually including the chip name in the file name). + +The code uses the [Atmel START](https://start.atmel.com/) ASFv4 library. + +USB DFU +======= + +This implementation support the following USB DFU capabilities: + +* can download: allowing to download the code over USB on the device (enabled per default) +* manifestation tolerant: allowing to download after a previous download (disabled per default) +* will detach: forcing the device the reset after a download, else it wit for a USB reset (enable per default) + +Set the corresponding attributes in the 'DFUD_IFACE_DESCB' macro definition in the 'usb/class/dfu/device/dfudf_desc.h' file. + +Compiling +========= + +Use the 'Makefile' script to compile the source code using the ARM none EABI GCC cross-cimpilig toolchain: +``` +cd gcc +make +``` + +The resulting firmware binary is `AtmelStart.bin`. + +Flashing +======== + +To flash the bootloader you can either use the [edbg tool](https://github.com/ataradov/edbg) over the EDBG interface of the SAM E54 Xplained Pro development board, or OpenICD with any SWJ adapter. + +The USB DFU bootloader should be flashed in a protected area of the flash memory to prevent for erasing it, as specified in data sheet section 25.6.2 Memory Organization. +The bootloader size is configured in the NVM user configuration BOOTPROT field, as specified in data sheet section 25.6.9 NVM User Configuration. +The bit position of the BOOTPROT field is documented in data sheet section 9.4 NVM User Page Mapping. +We need to reserve as least 2 pages of 8192 bytes for the bootloader since it is a bit larger than 10 KB (e.g. over 8 KB). +This setting will also tell the bootloader where to flash the application firmware to (e.g. after the bootloader reserved space). +The LED will blink once per second if this size is not set. + +EDBG +---- + +To flash the USB DFU bootloader, perform the following actions: +* remove reserved bootloader space so we can erase it: `edbg --target atmel_cm4v2 --fuse wv,29:26,15` +* erase the whole flash: `edbg --target atmel_cm4v2 --fuse v,29:26,15 --erase` +* program the bootloader: `edbg --target atmel_cm4v2 --fuse v,29:26,15 --program --verify --file AtmelStart.bin` +* reserve bootloader space: `edbg --target atmel_cm4v2 --fuse wv,29:26,13` -- To view, visit https://gerrit.osmocom.org/12516 To unsubscribe, or for help writing mail filters, visit https://gerrit.osmocom.org/settings Gerrit-Project: osmo-asf4-dfu Gerrit-Branch: master Gerrit-MessageType: newchange Gerrit-Change-Id: If884bca373aab10fe74d16f42b79dd6685eeabcf Gerrit-Change-Number: 12516 Gerrit-PatchSet: 1 Gerrit-Owner: Kévin Redon <kredon at sysmocom.de> -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.osmocom.org/pipermail/gerrit-log/attachments/20190109/f10aa08c/attachment.htm>