hello:
I installed the osmo-NITB on ubuntu18.04, including osmo-trx,osmo-bts,and openbsc.
The following is the print messages when these three applications start up.
1.osmo-trx
$ sudo osmo-trx-uhd -C osmo-trx-usrp_b200.cfg
Info: SSE3 support compiled in and supported by CPU
Info: SSE4.1 support compiled in and supported by CPU
Tue May 5 12:36:27 2020 DLGLOBAL <0007>
telnet_interface.c:104 Available via telnet 127.0.0.1 4237
Tue May 5 12:36:27 2020 DLCTRL <000e> control_if.c:911 CTRL
at 127.0.0.1 4236
Tue May 5 12:36:27 2020 DMAIN <0000> osmo-trx.cpp:484
[tid=139758118945664] Config Settings
Log Level............... 0
Device args.............
TRX Base Port........... 5700
TRX Address............. 127.0.0.1
GSM BTS Address......... 127.0.0.1
Channels................ 1
Tx Samples-per-Symbol... 4
Rx Samples-per-Symbol... 4
EDGE support............ 0
Extended RACH support... 0
Reference............... 1
Filler Burst Type....... Empty bursts
Filler Burst TSC........ 0
Filler Burst RACH Delay. 0
Multi-Carrier........... 0
Tuning offset........... 0
RSSI to dBm offset...... 28
Swap channels........... 0
Tx Antennas............. '<default>'
Rx Antennas............. '<default>'
Tue May 5 12:36:27 2020 DMAIN <0000> osmo-trx.cpp:438
[tid=139758118945664] Setting SCHED_RR priority 18
Tue May 5 12:36:27 2020 DDEVDRV <0006> log.cpp:460
[tid=139758008424192] [UHD] linux; GNU C++ version 7.4.0;
Boost_106501; UHD_3.14.0.HEAD-0-g6875d061
Tue May 5 12:36:27 2020 DDEV <0005> UHDDevice.cpp:470
[tid=139758118945664] Using discovered UHD device
type=b200,name=Lab_B210,serial=86680AA,product=B210
Tue May 5 12:36:28 2020 DDEVDRV <0006> b200_impl.cpp:386
[tid=139758008424192] [B200] Detected Device: B210
Tue May 5 12:36:29 2020 DDEVDRV <0006> b200_iface.cpp:441
[tid=139758008424192] [B200] Loading FPGA image:
/home/cruise/openBSC/osmo-trx/usrp_b210_fpga.bin...
Tue May 5 12:36:45 2020 DDEVDRV <0006> b200_impl.cpp:433
[tid=139758008424192] [B200] Operating over USB 3.
Tue May 5 12:36:45 2020 DDEVDRV <0006> b200_impl.cpp:484
[tid=139758008424192] [B200] Detecting internal GPSDO....
Tue May 5 12:36:46 2020 DDEVDRV <0006> gps_ctrl.cpp:253
[tid=139758008424192] [GPS] No GPSDO found
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:587
[tid=139758008424192] [B200] Initialize CODEC control...
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:650
[tid=139758008424192] [B200] Initialize Radio control...
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:957
[tid=139758008424192] [B200] Performing register loopback test...
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:966
[tid=139758008424192] [B200] Register loopback test passed
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:957
[tid=139758008424192] [B200] Performing register loopback test...
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:966
[tid=139758008424192] [B200] Register loopback test passed
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:758
[tid=139758008424192] [B200] Setting master clock rate selection
to 'automatic'.
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:1013
[tid=139758008424192] [B200] Asking for clock rate 16.000000
MHz...
Tue May 5 12:36:46 2020 DDEVDRV <0006> b200_impl.cpp:1024
[tid=139758008424192] [B200] Actually got clock rate 16.000000
MHz.
Tue May 5 12:36:47 2020 DMAIN <0000> UHDDevice.cpp:211
[tid=139758118945664] Antennas configured successfully
Tue May 5 12:36:47 2020 DDEVDRV <0006> multi_usrp.cpp:502
[tid=139758008424192] [MULTI_USRP] Setting master clock rate
selection to 'manual'.
Tue May 5 12:36:47 2020 DDEVDRV <0006> b200_impl.cpp:1013
[tid=139758008424192] [B200] Asking for clock rate 26.000000
MHz...
Tue May 5 12:36:47 2020 DDEVDRV <0006> b200_impl.cpp:1024
[tid=139758008424192] [B200] Actually got clock rate 26.000000
MHz.
Tue May 5 12:36:47 2020 DDEV <0005> UHDDevice.cpp:275
[tid=139758118945664] Rates configured for B210 4 SPS
Tue May 5 12:36:47 2020 DDEV <0005> UHDDevice.cpp:235
[tid=139758118945664] Supported Tx gain range [0; 89.75]
Tue May 5 12:36:47 2020 DDEV <0005> UHDDevice.cpp:240
[tid=139758118945664] Supported Rx gain range [0; 76]
Tue May 5 12:36:47 2020 DDEV <0005> UHDDevice.cpp:244
[tid=139758118945664] Default setting Tx gain for channel 0 to
44.875
Tue May 5 12:36:47 2020 DDEV <0005> UHDDevice.cpp:251
[tid=139758118945664] Default setting Rx gain for channel 0 to 38
Tue May 5 12:36:47 2020 DDEV <0005> UHDDevice.cpp:569
[tid=139758118945664] Device configuration: Single USRP:
Device: B-Series Device
Mboard 0: B210
RX Channel: 0
RX DSP: 0
RX Dboard: A
RX Subdev: FE-RX2
TX Channel: 0
TX DSP: 0
TX Dboard: A
TX Subdev: FE-TX2
Tue May 5 12:36:47 2020 DMAIN <0000> osmo-trx.cpp:532
[tid=139758118945664] -- Transceiver active with 1 channel(s)
when the osmo-bts-trx launched later, the following messages will arise, shows that the osmo-trx received the 'POWEROFF' command and feed back the 'RESPONSE' to osmo-bts-trx.
Tue May 5 12:42:44 2020 DTRXCTRL <0002>
Transceiver.cpp:832 [tid=139758118945664][chan=0] command is
'POWEROFF'
Tue May 5 12:42:44 2020 DTRXCTRL <0002> Transceiver.cpp:977
[tid=139758118945664][chan=0] response is 'RSP POWEROFF 0'
POWERON command was not launched.
and the USRP TX/RX LED was not lighted.
2.osmo-bts-trx
$ sudo osmo-bts-trx
((*))
|
/ \ OsmoBTS
<0017> control_if.c:911 CTRL at 127.0.0.1 4238
<0010> telnet_interface.c:104 Available via telnet 127.0.0.1
4241
<0012> input/ipaccess.c:1024 enabling ipaccess BTS mode, OML
connecting to 192.168.122.1:3002
<000b> trx_if.c:1174 phy0.0: Open transceiver
About one minutes later, the
osmo-bts-trx will exit automatically, and the following
messages was printed.
<0012> e1_input.c:243 abis_sendmsg: msg->dst == NULL: 0c
12 01 90 0f 00 c8
<0012> e1_input.c:243 abis_sendmsg: msg->dst == NULL: 0c
12 01 88 12 06 00 00 00 00 00 00
<000d> abis.c:143 Signalling link down
<0001> bts.c:293 Shutting down BTS 0, Reason Abis close
Shutdown timer expired
3. osmo-nitb
$ sudo osmo-nitb -c osmo-nitb-ipa.cfgDB: Database prepared.
In a word, the hardware USRP TX/RX LED has not been lighted, it
seems not work. How to poweron it?