Matt.
I don’t think this works with Graham’s op25 (rx.py) fork having tried a number of configurations (combinations) but not able to decode conventional P25 non-trunked IMBE. Perhaps Graham or Max can elaborate if this functionality is still supported.
Thanks again!
Bill, WA8WG
From: op25-dev@yahoogroups.com [mailto:op25-dev@yahoogroups.com]
Sent: Monday, December 18, 2017 5:54 PM
To: op25-dev@yahoogroups.com
Subject: Re: [op25-dev] Recent changes
Hi Bill,
trunk.csv isn't required for conventional. Here's a few exmaple commands I have used with my USRPs (via UHD) and airspy:-
./rx.py -S 2500000 -o 50000 -q 2 -f 434075000 --args 'uhd' -D fsk4 -P fft --gains 'PGA:10'
./rx.py -S 1000000 -o 50000 -q 39 -f 434075000 --args 'uhd' --gains 'PGA:40'
./rx.py -S 2500000 -o 50000 -q 2 -f 438187500 --args 'airspy' -D fsk4 -P fft --gains 'MIX:5'
/rx.py -S 1000000 -o 50000 -q 2 -f 438187500 --args 'uhd' -D fsk4 -P fft --gains 'PGA:30'
Cheers,
Matt
On 19 December 2017 at 09:06, 'William Becks' wa8wg@centurytel.net [op25-dev] <op25-dev@yahoogroups.com> wrote:
OK. How does one setup the rx.py command line and/or trunk.tsv file if required to monitor conventional traffic? Can you please post example configuration?
Thank you,
Bill, WA8WG
From: op25-dev@yahoogroups.com [mailto:op25-dev@yahoogroups.com]
Sent: Monday, December 18, 2017 2:43 PM
To: op25-dev@yahoogroups.com
Subject: Re: [op25-dev] Recent changes
rx.py can already monitor conventional traffic. In fact this feature was there before trunking was.
On Tue, 19 Dec 2017 at 06:55, 'William Becks' wa8wg@centurytel.net [op25-dev] <op25-dev@yahoogroups.com> wrote:
Graham,
Thank you so much for your efforts in the continuing development of op25. Especially for the recent coding changes allowing for FQDN --wireshark-host command line entry. The addition of the --nocrypt function was very innovative and solved an issue in my area where some talkgroups use a mix of clear, and encrypted transmissions that were previously impossible to reject without also filtering the clear voice transmissions as well..
I am personally very grateful for the work that you and Max have done to improve the code. If I could wish for one new feature, it would be to incorporate code allowing rx.py to monitor conventional IMBE non-trunked transmissions. Such a feature would be great for monitoring small non-trunked systems in addition to providing a great resource to monitor and analyze amateur P25 transmissions from MMDVM and similar devices.
Keep up the good work and best of holiday greetings!
Bill, WA8WG
From: op25-dev@yahoogroups.com [mailto:op25-dev@yahoogroups.com]
Sent: Saturday, December 16, 2017 7:08 PM
To: op25-dev@yahoogroups.com
Subject: [op25-dev] Recent changes
For my version of op25 I've just pushed a change to support using hostnames/fully qualified domain names (or straight IP addresses) in the --wireshark-host command line parameter (-W).
Earlier changes include the addition of the source radio id (where available) to the terminal screen, as well as indication of when encryption is active (only applies when using --nocrypt command line option).
Posted by: "William Becks" <wa8wg@centurytel.net>
| Reply via web post | • | Reply to sender | • | Reply to group | • | Start a New Topic | • | Messages in this topic (12) |
