Hi,all:
    I have got a C118 to test mobile function
    1) To get the  master branch code and to compile it. 
    2) To  insert  simcard(13681******) into the phone and to modify the mobile.cfg to use real simcard. 
    3) To connect the phone with PC(core i5/ubuntu 12.04). 
    4) After downloading the firmware,  to start the mobile App(#sudo ./mobile 2>&1 | tee > log.txt).
    5) I can see that the location update process is ok and an TMSI is allocated to the phone.
    6) To telnet into the osmocon, I can start a call to another phone (#Call 1 13564******).
     7) I can send a sms to another phone.              
     So far, all(MOC) is ok.

     But If using the osmocommbb phone(13681******) as the target phone(MOT), (for example, I
use a normal phone to call the osmocombb phone), it is very rare that the osmocombb phone have a respose to the paging.
     1) I have check the paging messages in the log.txt file and  find that there only one paging respone  messages such as "TMSI MATCH" as I have 
          call the osmocombb  phone about 20 times. In the success case:
 ..............
gsm322.c:1966 Cell ARFCN 13 selected.
gsm322.c:2423 Tune to frequency 13.
gsm322.c:468 Sync to ARFCN=13 rxlev=-68 (Sysinfo, ccch mode NON-COMB)
gsm322.c:2450 Cell available.
gsm322.c:4049 (ms 1) Event 'EVENT_CELL_FOUND' for Cell selection in state 'C5 choose cell'
gsm322.c:3383 Camping normally on cell (ARFCN=13 mcc=460 mnc=00  China, China Mobile)
gsm322.c:829 new state 'C5 choose cell' -> 'C3 camped normally'
gsm48_mm.c:4325 (ms 1) Received 'MM_EVENT_CELL_SELECTED' event in state wait for network command
gsm48_mm.c:1130 We are in registered LAI as returning to MM IDLE
gsm48_mm.c:919 new state wait for network command -> MM IDLE, normal service
gsm48_mm.c:426 starting T3212 (periodic loc. upd. delay) with 7200 seconds
gsm322.c:2947 Channel synched. (ARFCN=13, snr=16, BSIC=29)
..............        
gsm48_rr.c:2116  TMSI a0b186e9 matches
gsm48_rr.c:1307 Establish radio link due to paging request
gsm322.c:4049 (ms 1) Event 'EVENT_LEAVE_IDLE' for Cell selection in state 'C3 camped normally'
gsm322.c:829 new state 'C3 camped normally' -> 'connected mode 1'
gsm322.c:3665 Going to camping (normal) ARFCN 13.
gsm322.c:468 Sync to ARFCN=13 rxlev=-68 (Sysinfo, ccch mode NON-COMB)
gsm48_rr.c:355 new state idle -> connection pending
gsm48_rr.c:1422 CHANNEL REQUEST: 20 (PAGING TCH/F)
gsm322.c:2947 Channel synched. (ARFCN=13, snr=16, BSIC=29) 
..........
      From the log info I can see that:
      a) the phone is camped in ARFCN 13 and receive paging in this cell.
      b) the signal of cell is strong enough              
      
     2) I have no an OpenBTS device to send some paging messages to check where is the problem further.
     Maybe I miss something. 
     Any suggestion is appreciated!
     Thank you very much!

Best Regards

Shang