Unfortunately, Protocase can't supply proper heat sink as we might wish.<div><div><br></div></div><div class="gmail_extra"><br clear="all">Best regards,<div>Andrey Sviyazov.</div><br>
<br><br><div class="gmail_quote">2012/11/12 Alexander Chemeris <span dir="ltr"><<a href="mailto:alexander.chemeris@gmail.com" target="_blank">alexander.chemeris@gmail.com</a>></span><br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div class="im">On Thu, Nov 8, 2012 at 11:30 PM, Darby <<a href="mailto:darbysgoodies@gmail.com">darbysgoodies@gmail.com</a>> wrote:<br>
>> I'm not sure whether you actually need a 3D design here? As I see it,<br>
>> you select a proper existing case and just design front/rear panels<br>
>> and drilling pattern for mounting. I may be wrong, though - I've never<br>
>> done this before. I just worry that a fully custom case could be too<br>
>> expensive in small quantities.<br>
><br>
> Im sure you could use a preexisting design, and just punch some holes<br>
> in the sides for convection cooling, then punch some holes in the back<br>
> to accommodate power & cabling, and use some motherboard standoffs<br>
> that would keep the board mounted in place on the enclosure floor.<br>
<br>
</div>Yes, I was looking for something like that - simple and inexpensive.<br>
It would be a shame if a case cost a considerable part of the thing.<br>
<div class="im"><br>
> I was thinking more along the lines of stamped/bent sheet metal, some<br>
> lightpipes (plexyglass or polycarbonate) in the front so youve got<br>
> visibility of the lights in the front & some countersunk holes on the<br>
> sides to keep the 2 C shaped (or L shaped would work well too? -Which<br>
> might be a better implementation for mounting purposes if youre going<br>
> with lightpipes as opposed to holes in the case for lights) pieces<br>
> bolted together & a powdercoated or painted finish?<br>
<br>
</div>For lab version we could use 3-LED columns, like the ones we used in UmTRXv1:<br>
<a href="http://wiki.umtrx.googlecode.com/hg/images/umtrxv1/UmTRX-top.jpg" target="_blank">http://wiki.umtrx.googlecode.com/hg/images/umtrxv1/UmTRX-top.jpg</a><br>
UmTRXv2 has places to colder them instead of SMD LEDs:<br>
<a href="http://wiki.umtrx.googlecode.com/hg/images/umtrxv2/UmTRXv2.jpg" target="_blank">http://wiki.umtrx.googlecode.com/hg/images/umtrxv2/UmTRXv2.jpg</a><br>
In this case light-pipes are not needed and we could just drill holes<br>
at the front panel.<br>
<br>
I have no preference between U/C, L or slide-in cases. Anything which<br>
is easy to handle, inexpensive and looks good is fine.<br>
<div class="im"><br>
> I found some design tools at protocase, that it looks as though will<br>
> pushout 3d cad files as deliverables, but looking thru the project<br>
> files -I cant seem to find anything that would give me specifics on<br>
> distances between the mounting holes from each other's centerpoints &<br>
> how wide these holes are, If someone can point me to a place where I<br>
> can find this -Ill take a stab at case design when Ive got some free<br>
> time... š =)<br>
<br>
</div>No idea, sorry. I think you'd best contact Protocase with this uestion<br>
- I think they should be interested in supporting potential customers.<br>
<div class="im"><br>
> On a side note, They also have an extruded aluminum offering<br>
> (<a href="http://www.protocase.com/products/index.php?e=Aluminum" target="_blank">http://www.protocase.com/products/index.php?e=Aluminum</a>) where the<br>
> sides are the same between the left & the right, with a fixed height<br>
> of 1.72" (43.688mm). For mounting they use some internal channels that<br>
> the board will slide into (as opposed to motherboard standoffs as<br>
> suggested above) then they use a sheetmetal bridge for the top &<br>
> bottom to determine the width & then sheetmetal on front & back as<br>
> well -Depending on quantity, they might be willing to sell lengths<br>
> (like say 10 or 20ft at a time) that your people could cut to size &<br>
> fabricate their own top/bottom/front/back panels?<br>
><br>
> Just a thought...<br>
<br>
</div>Hum, this looks interesting. Though we need something ready, i.e.<br>
already cut and with ready-to-use front/back panels.<br>
<br>
I wonder how much would it cost to get cases shipped from them to<br>
Europe. For, say, 20-50pcs.<br>
<div class="HOEnZb"><div class="h5"><br>
--<br>
Regards,<br>
Alexander Chemeris.<br>
CEO, Fairwaves LLC / ïïï õÍòÁÄÉÏ<br>
<a href="http://fairwaves.ru" target="_blank">http://fairwaves.ru</a><br>
<br>
</div></div></blockquote></div><br></div>