<div class="gmail_extra">Hi Alexander.<br><br><div class="gmail_quote">2012/11/10 Alexander Chemeris <span dir="ltr"><<a href="mailto:alexander.chemeris@gmail.com" target="_blank">alexander.chemeris@gmail.com</a>></span><br>
<blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">Hi Andrey,<br>
<div class="im"><br>
On Fri, Nov 9, 2012 at 9:55 PM, Andrey Sviyazov <<a href="mailto:andreysviyaz@gmail.com">andreysviyaz@gmail.com</a>> wrote:<br>
</div><div class="im">> I got two UmTRXv2 and both with the problems of inaccurate assembling.<br>
<br>
</div>I wonder, do they do at least visual inspection of boards after<br>
assembly? This again reminds us that we have to create a test<br>
procedure for the fab before we start manufacturing in quantities. If<br>
you're a community member who could contribute to the test procedure -<br>
we would greatly appreciate that (mention on the web-site, t-shirt,<br>
even free hardware).</blockquote><div> </div><div><div>I am afraid that I didn't understood what do you mean.</div><div><br></div></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">

<br>
I'm willing to try a simple semi-automated visual testing - make<br>
pictures of all boards and then subtract them from a reference one. If<br>
performed well, we should clearly see all errors on the resulting<br>
picture. The only question is how hard is it to "perform well".<br></blockquote><div> </div><div>Do you mean to design some tooling and firmware/software for testing?</div><div> </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">
<div class="im"><br>
> 1st Thomas sent to me and 2nd was new and clear (say, virgin).<br>
><br>
> Thomas said about power supply symptoms few days ago.<br>
> I fixed assembling error in DC/DC - power coil (L37) was 90 degrees rotated.<br>
> It was too big surprise for me, because I replaced all components around<br>
> coil before I saw that it soldered incorrect.<br>
> Anyhow,This board began to work, but LMS2 still didn't hears SPI and didn't<br>
> work.<br>
<br>
</div>Do you think it's a result of bad soldering and rework might help?<br></blockquote><div> </div><div>I'll try to fix LMS2. It is doable for me because required just warm up board and to push LMS2 a little bit.</div>
<div>  </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">
<div class="im"><br>
> Also I found that mashine lost one 0.1uF cap (C86-1) near LMS1, but it was<br>
> easily to fix.<br>
> LMS1 and all other parts, seems working fine.<br>
><br>
> Second board programmed and working, but FPGA too hot and 3.3V loaded a lot.<br>
<br>
</div>You think the FPGA itself is broken?<br></blockquote><div> </div><div>If everything work, then extra current goes inside FPGA chip.</div><div>So, yes, I'm sure, almost.</div><div> </div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">

<div class="im"><br>
> Seems, I have to find BGA reworking station to fix both boards finally.<br>
> Also needed new Spartan-6 FPGA for replace.<br>
> Alexander, do we have spare on hands?<br>
<br>
</div>Nothing on hands. We should check with Andrew Karpenkov and his<br>
connections at InlineGroup - they should have a stock of those chips<br>
and a BGA reworking station. E.g. they repaired our blown SP-605.</blockquote><div> </div><div>It would be fine, if InlineGroup can repair this board.</div><div>I know that without FPGA repair station I can easy to damage PCB and I want to do it.<br>
</div><div>At least we need to order FPGA with lead solder balls to make repair at lower tem.</div><br clear="all">Best regards,<div>Andrey Sviyazov.</div></div></div>