<div>Since we decided to make version 3 (due to additions of šLMS thermosensors) then we can also add external Fref prescaler for PLL, no problems here.</div><div>I think ICPR is more important restriction.</div><div>Srdjan said that it doesn't studied too deeply, but on my opinion, really reachable maximum Tx power no more then 25 dBm (without DPD).</div>
<div>So, we can't use LMS for LTE without DPD or additional filtration (2nd Tx IF).</div><div>In other hand, we can implement it similar to UmSEL and with upconversion, of course, but high quality SAW filter required (all flatness) to keeping EVM as small as possible.</div>
<div><br clear="all">Best regards,<div>Andrey Sviyazov.</div><br>
<br><br><div class="gmail_quote">2012/10/14 Alexander Chemeris <span dir="ltr"><<a href="mailto:alexander.chemeris@gmail.com" target="_blank">alexander.chemeris@gmail.com</a>></span><br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Srdjan, thanks for the answers. This is enough for us at the moment.<br>
<div class="HOEnZb"><div class="h5"><br>
On Sun, Oct 14, 2012 at 3:50 PM, Srdjan Milenkovic<br>
<<a href="mailto:s.milenkovic@limemicro.com">s.milenkovic@limemicro.com</a>> wrote:<br>
> Hi Alexander,<br>
> Remaining questions are addressed below.<br>
><br>
><br>
> On 13/10/2012 21:47, Alexander Chemeris wrote:<br>
><br>
> Hi Srdjan,<br>
><br>
> We're looking into re-purposing UmTRX for LTE and there a few things which<br>
> we need to understand better.<br>
><br>
> 1. Is it possible to support 15MHz and 20MHz LTE channel bandwidths? To<br>
> achieve this we at least need to sample at 23.04Msps and 30.72Msps<br>
> respectively. LMS6002D datasheet specifies the maximum I/Q samplerate of<br>
> 14Msps, which is not enough. But at the same time, datasheet claims that ADC<br>
> and DAC are specified up to 50Msps. How does this fits together?<br>
><br>
> 2. Do you have any experience what maximum output power we could achieve<br>
> with LMS and proper amplifiers, while still staying in the bounds of the LTE<br>
> Standard? What would be the limiting factor for the further power increase?<br>
><br>
> The limiting factor here would be absolute specs on ACPR, out of band spurs<br>
> ... i.e. TX spectrum mask, expressed in dBm not in dBc. For example, you may<br>
> meet <= -45dBc ACPR but on the other hand you can not inject noise into<br>
> adjacent channel more than xdBm. LMS device is OK for 20-25dBm modulated<br>
> output power. We can probably push it more however this is šnot tested so<br>
> far.<br>
><br>
><br>
><br>
> 3. Is there any issues using TDD mode in LMS6002D? We've been using onnly<br>
> FDD mode so far and it would be great to know what issues could we expect<br>
> when switching to TDD mode.<br>
><br>
> TDD mode should be just fine. We measured around 20us TX<->RX switching<br>
> time. We will probably need to reconfigure VCO supplies on UmTRX board to<br>
> simplify switching control while keeping switching time at 20us. Lat us know<br>
> when you are ready for such experiment.<br>
><br>
><br>
><br>
> --<br>
> Regards,<br>
> Alexander Chemeris.<br>
> CEO, Fairwaves LLC / ïïï õÍòÁÄÉÏ<br>
> <a href="http://fairwaves.ru" target="_blank">http://fairwaves.ru</a><br>
><br>
><br>
<br>
<br>
<br>
--<br>
Regards,<br>
Alexander Chemeris.<br>
CEO, Fairwaves LLC / ïïï õÍòÁÄÉÏ<br>
<a href="http://fairwaves.ru" target="_blank">http://fairwaves.ru</a><br>
<br>
</div></div></blockquote></div><br></div>