<div><br></div>Hi all!<div><br><div>First of all, I forgot one question regarding the IF SAW filters.</div><div>TB0130A has at least 10dB higher rejection at 0.6-0.9MHz offset band (65dB) than TB448A (55dB), and 20dB higher rejection at 0.9-1.5MHz offset band (75dB instead of 55dB). </div>
<div>Moreover, TB0130A has more flatter and wider passband, approx 300kHz at 0.5dB instead of 250kHz for TB448A, it is better because of this type SAW has thermal drift approx +-32 kHz for +-50'C relative to +25'C. </div>
<div>In other hand, TB448A has better group delay ripples, but I don't how it critical for GMSK, and I'm sure that symmetry law more important.</div><div>Also we can adjust central IF for 3-5 temperature points, but in this case we need to add thermal measurements, and let we try to avoid it.</div>
<div><br><div>Best regards,<div>Andrey Sviyazov.</div><br>
<br><br><div class="gmail_quote">19 марта 2012 г. 12:30 пользователь Andrey Sviyazov <span dir="ltr"><<a href="mailto:andreysviyaz@gmail.com">andreysviyaz@gmail.com</a>></span> написал:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Hi Alexander.<div><br></div><div><div>Actualy I don't know side-type connectors for cable.</div><div>I suggested you PCB side connector (like PCI) for debugging only.</div><div>Moreover, there are a lot SMD connectors for IDC flat cable, BHS-10 for example.</div>

</div><div> <br clear="all">Best regards,<div>Andrey Sviyazov.</div><br>
<br><br><div class="gmail_quote">19 марта 2012 г. 10:14 пользователь Alexander Chemeris <span dir="ltr"><<a href="mailto:alexander.chemeris@gmail.com" target="_blank">alexander.chemeris@gmail.com</a>></span> написал:<div>
<div class="h5"><br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Andrey,<br>
<br>
2012/3/19 Andrey Sviyazov <<a href="mailto:andreysviyaz@gmail.com" target="_blank">andreysviyaz@gmail.com</a>>:<br>
<div>> 5) Regarding connectors, I only can suggest to use the two angle SMA-female<br>
> connectors for outputs which will stick out through the panel of the housing<br>
> (as you can use the angle SMA connectors, but for GPS and CLK_I/O on the<br>
> UmTRX board). At the same time for the internal 4 connectors we can use some<br>
> cheap like U.FL and cable assemblies U.FL-MCX or  U.FL-U.FL. Signal<br>
> CLK_26MHz,  6.5VDC, SPI and Switch controls will go via IDC control<br>
> connector.<br>
<br>
</div>IDC connectors on a UmTRX and on a RF board will be connected with a<br>
flat ribbon cable?<br>
<br>
Why don't you want to use a side connector?<br>
<div><div><br>
--<br>
Regards,<br>
Alexander Chemeris.<br>
CEO, Fairwaves LLC / ООО УмРадио<br>
<a href="http://fairwaves.ru" target="_blank">http://fairwaves.ru</a><br>
</div></div></blockquote></div></div></div><br></div>
</blockquote></div><br></div></div></div>