This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/osmocom-sdr@lists.osmocom.org/.
R B abcd at bitmessage.chHello Gang ;) i have some troubles, properly "misusing" my vga-adapter. the samplerate while testing with fl2k_test is pretty low (~50MS/s) and i am not sure if this is some hardware issue or. RF-Output isn´t detectable either. i am using a lenovo thinkpad x1 hybrid (1294). any help is appreciated. $ fl2k_test -s 162e6 Reporting PPM error measurement every 10 seconds... Press ^C after a few minutes. real sample rate: 52862885 current PPM: -673686 cumulative PPM: -673686 real sample rate: 52973828 current PPM: -673001 cumulative PPM: -673342 real sample rate: 53014975 current PPM: -672747 cumulative PPM: -673143 real sample rate: 52979890 current PPM: -672964 cumulative PPM: -673098 ^CSignal caught, exiting! $ fl2k_test -s 51e6 Reporting PPM error measurement every 10 seconds... Press ^C after a few minutes. real sample rate: 51037366 current PPM: 733 cumulative PPM: 733 real sample rate: 51031823 current PPM: 624 cumulative PPM: 678 real sample rate: 51025418 current PPM: 498 cumulative PPM: 617 real sample rate: 51023557 current PPM: 462 cumulative PPM: 578 real sample rate: 51019821 current PPM: 389 cumulative PPM: 540 real sample rate: 51017641 current PPM: 346 cumulative PPM: 507 ^CSignal caught, exiting! $ sudo lspci -vv|grep "USB 3" -A 200 0f:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI]) Subsystem: Lenovo uPD720200 USB 3.0 Host Controller Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at f1400000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Vector table: BAR=0 offset=00001000 PBA: BAR=0 offset=00001080 Capabilities: [a0] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 unlimited ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp- LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR+, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Kernel driver in use: xhci_hcd $ lsusb Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 002: ID 1d5c:2000 Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub $ usb-devices |grep "Bus=04 Lev=01" -A 100 T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0 D: Ver= 3.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1 P: Vendor=1d5c ProdID=2000 Rev=02.00 C: #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=496mA I: If#= 0 Alt= 0 #EPs= 0 Cls=10() Sub=00 Prot=00 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=10() Sub=02 Prot=00 Driver=(none) I: If#= 2 Alt= 0 #EPs= 1 Cls=10() Sub=02 Prot=00 Driver=(none) $ lsmod|grep usb $ lsmod|grep xhci thank you and cheers robin -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.osmocom.org/pipermail/osmocom-sdr/attachments/20180516/3771eb57/attachment.htm>