<div dir="ltr"><span style="font-size:12.8px">>It sounds like you need a raw IQ sampled binary file at about 5 Msps.</span><br style="font-size:12.8px"><span style="font-size:12.8px">>Is that correct?</span><br style="font-size:12.8px"><br><span style="font-size:12.8px">Thanks a lot for your hints!</span><br style="font-size:12.8px"><br style="font-size:12.8px"><span style="font-size:12.8px">If my math (sampling theorem) is not wrong, because I need a bandwidth</span><br style="font-size:12.8px"><span style="font-size:12.8px">of 5 MHz (assuming only downstream transmission, given I will not use</span><br style="font-size:12.8px"><span style="font-size:12.8px">upstream), it would require 5 Msps in case each sample is a complex number</span><br style="font-size:12.8px"><span style="font-size:12.8px">or 10 Msps in case the samples are real-valued.</span><br style="font-size:12.8px"><span style="font-size:12.8px"><br>>There are a variety of methods to achieve this depending on your</span><br style="font-size:12.8px"><span style="font-size:12.8px">>requirements. You could generate the multiplexed signal live with up</span><br style="font-size:12.8px"><span style="font-size:12.8px">>to 3 adjacent ARFCN channels (800 kHz separation) with a B200 and</span><br style="font-size:12.8px"><span style="font-size:12.8px">>osmo-trx with multi-ARFCN enabled.</span><br style="font-size:12.8px"><span style="font-size:12.8px"><br></span><div><span style="font-size:12.8px">That is a good starting point. But I would need to increase the number</span><br style="font-size:12.8px"><span style="font-size:12.8px">of 200 kHz to reach a total of 5 MHz.</span><br><br style="font-size:12.8px"><span style="font-size:12.8px">>But, it sounds like you just need a test file, so you could</span><br style="font-size:12.8px"><span style="font-size:12.8px">>post-process an existing single ARFCN signal file in Octave or Matlab</span><br style="font-size:12.8px"><span style="font-size:12.8px">>to carry multiple versions of the same GSM signal. That may or may not</span><br style="font-size:12.8px"><span style="font-size:12.8px">>be sufficient depending on your needs.<br></span><span style="font-size:12.8px"><br>Yes, exactly: just a test file. I am still studying the GSM PHY and I</span><br style="font-size:12.8px"><span style="font-size:12.8px">suspect if I simply position the ARFCNs in different frequencies I</span><br style="font-size:12.8px"><span style="font-size:12.8px">will end up with an invalid GSM signal (that is, it will not be properly</span><br style="font-size:12.8px"><span style="font-size:12.8px">decoded by the Keysight VSA equipment that I have to interface to).</span><br></div></div><div class="gmail_extra"><br clear="all"><div><div class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div><div></div>Marcus Dias<br></div>UFPA - Lasse - LaPS<br></div></div></div></div></div>
<br><div class="gmail_quote">2017-05-09 15:41 GMT-03:00 Tom Tsou <span dir="ltr"><<a href="mailto:tom@tsou.cc" target="_blank">tom@tsou.cc</a>></span>:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi Marcus,<br>
<span class=""><br>
On Tue, May 9, 2017 at 9:53 AM, Marcus Dias <<a href="mailto:vmarcusv@gmail.com">vmarcusv@gmail.com</a>> wrote:<br>
> Most BTS code I have, generate only one or two 200 kHz channels, but I need<br>
> to test a receiver using several (multiplexed) 200 kHz channels, composing<br>
> approximately 5 MHz of total bandwidth. This should be a "valid" multiplex<br>
> signal (correct and "decodable" control channel). Can anyone pointout where<br>
> should I start to put together the software to generate a binary file with<br>
> such signal? I guess I can inspect the code of a BTS that supports two TRX<br>
> (two 200 kHz channels) but I would like to double check whether there is a<br>
> more direct approach.<br>
<br>
</span>It sounds like you need a raw IQ sampled binary file at about 5 Msps.<br>
Is that correct?<br>
<br>
There are a variety of methods to achieve this depending on your<br>
requirements. You could generate the multiplexed signal live with up<br>
to 3 adjacent ARFCN channels (800 kHz separation) with a B200 and<br>
osmo-trx with multi-ARFCN enabled.<br>
<br>
But, it sounds like you just need a test file, so you could<br>
post-process an existing single ARFCN signal file in Octave or Matlab<br>
to carry multiple versions of the same GSM signal. That may or may not<br>
be sufficient depending on your needs.<br>
<span class="HOEnZb"><font color="#888888"><br>
  -TT<br>
</font></span></blockquote></div><br></div>