<div dir="ltr">

<p class="MsoNormal">Hello, my name is Diego.</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">I've a configurated sysmoBTS in OpenBSC network-in-the-box
(NITB) mode, and the osmo-nitb is working fine, doing and receiving calls and
messages between the phones connected to the sysmoBTS network. </p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">At this point I would need to call outside the OpenBSC, and
I would be very gratefull if someone could help me with some doubts I have. I’m
new in this.</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">For the isdn card capable of NT-mode, I’ve seen the “OpenVox
B200P 2-port ISDN BRI PCI” card for buying, but:</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">1-An “OpenVox B100P ISDN BRI PCI” card, with only one RJ45
female connector, could be used correctly, working together with an already
installed PCI Ethernet Controller card? Or, is it better an isdn card with two
RJ45 connectors in the same card? One for connecting the BTS to the computer,
and the another for connecting the computer to a LAN through a router or
switch? I would like to avoid to cut cables as the LCR guide says,
<a href="http://isdn.eversberg.eu/download/doc-1.4/linux-call-router-1.4_1.pdf">http://isdn.eversberg.eu/download/doc-1.4/linux-call-router-1.4_1.pdf</a>, and the
problems with the cross over and not crossed cables.</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">2-The “Howto OpenBSC with Asterisk and LCR” guide,
<a href="http://openbsc.osmocom.org/trac/wiki/OpenBSC_LCR">http://openbsc.osmocom.org/trac/wiki/OpenBSC_LCR</a>, indicates that it’s necessary
compile and install LibOsmocore and OpenBSC, but the OpenBSC/OsmoNITB inside
the sysmoBTS is working, so I’m not sure about this step. If the solution is to
build, configure and run OpenBSC/OsmoNITB + OsmoSGSN + OpenGGSN on a PC and
configure the sysmoBTS to connect to this, should I change the image of the BTS
and its whole configuration?</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">3-Although I don’t have the isdn card yet, for testing some
configurations in the PC I followed the “Building and Running OpenBSC with
Asterisk” Pierre Kim guide, that I believe is newer than the “How to OpenBSC
with Asterisk and LCR”, and I haven’t problems with the installations. So if
I<span style>  </span>run the lcr:</p><p class="MsoNormal"><br></p>

<p class="MsoNormal"># lcr start <br></p>

<p class="MsoNormal">** LCR Version 1.14 <br></p>

<p class="MsoNormal">LCR 1.14 started, waiting for calls…</p>

<p class="MsoNormal">  <br></p>

<p class="MsoNormal">and running the osmo-nitb:</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal"># ./osmo-nitb -m -P </p>

<p class="MsoNormal">DB: Database initialized.</p>

<p class="MsoNormal">DB: Database prepared.</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">My question in this point, is it only necessary to connect
the BTS to the isdn card with the right OpenBSC to finish the system
configuration?</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">Many thanks for your time and for your work.</p>

<p class="MsoNormal"> </p>

<p class="MsoNormal">Kindest regards,</p>

<p class="MsoNormal">Diego.</p>

</div>