<html><body style="word-wrap: break-word; -webkit-nbsp-mode: space; -webkit-line-break: after-white-space; ">Hello Dieter,<div><br></div><div><blockquote type="cite"><div>You did turn the power off for a restart, just to be sure ?</div></blockquote>Yes, of course ;)</div><div><br></div><div><blockquote type="cite"><div>If the firmware for the first TRX is not loaded, the Abis<br>communication will still work because the microcontroller<br>which takes care about the commnunication is working. The<br>error messages result from the not working TRX (I guess<br>it would work if TRX1 instead of TRX0 is used, however I<br>have not tried it yet).</div></blockquote><br></div><div>What do I have to do to use the second TRX instead?</div><div>Plug in the other Twinax connectors?</div><div>Do I need to setup the second TRX separately on LMT?</div><div><br></div><div>Thanks ;)</div><div><br></div><div>Björn</div><div><br></div><div><br><div><div>Am 23.04.2009 um 09:05 schrieb Dieter Spaar:</div><br class="Apple-interchange-newline"><blockquote type="cite"><div>Hallo Bjoern,<br><br><blockquote type="cite">I tried it several times,<br></blockquote><blockquote type="cite">and left the BTS on over night.<br></blockquote><blockquote type="cite">The LMT cable wasn't always plugged in.<br></blockquote><blockquote type="cite">When I boot up the BTS it always says that the second TRX<br></blockquote><blockquote type="cite">has Load and the first not.<br></blockquote><br>You did turn the power off for a restart, just to be sure ?<br><br><blockquote type="cite">If I try to bring up the BTS with your SW under Win.<br></blockquote><blockquote type="cite">I get the Abis Link Up but when I try the Load DB I get some<br></blockquote><blockquote type="cite">error messages on LMT.<br></blockquote><blockquote type="cite">Then the second TRX goes down to No Load.<br></blockquote><br>If the firmware for the first TRX is not loaded, the Abis<br>communication will still work because the microcontroller<br>which takes care about the commnunication is working. The<br>error messages result from the not working TRX (I guess<br>it would work if TRX1 instead of TRX0 is used, however I<br>have not tried it yet).<br><br><blockquote type="cite">And this is the condition until I reboot the BTS.<br></blockquote><blockquote type="cite">Maybe its a software issue?<br></blockquote><br>I don't think so because the communication processor loads the<br>same firmware in both TRX. This is done in parallel. In your<br>trace there is the same behavior I experience here, loading the<br>firmware for TRX0 ad TRX1 starts, however loading TRX0 stops<br>immediately. Of course I can only speak for my BS-11, but here<br>it is most certainly a hardware issue (at one time I could even<br>see an error message that the first power supply unit did not<br>start).<br><br>Best regards,<br> Dieter<br>-- <br>Dieter Spaar, Germany <a href="mailto:spaar@mirider.augusta.de">spaar@mirider.augusta.de</a><br><br></div></blockquote></div><br><div apple-content-edited="true"> <div style="word-wrap: break-word; -webkit-nbsp-mode: space; -webkit-line-break: after-white-space; "><div><div>- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -</div><div>Björn Heller</div><div>Jabber: <a href="mailto:tec@jabber.hellercom.de">tec@jabber.hellercom.de</a></div></div></div> </div><br></div></body></html>