This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/OpenBSC@lists.osmocom.org/.
Sipos Csaba sipos.csaba at kvk.uni-obuda.huDear Alexander, > Any reason it's specific to B2x0? Not really, now that UmTRX also uses the standard UHD branch, it should be the same. The only reason is that I have a B200 and a B210 (finally) to test, but I dont have for example a UmTRX, so I cant validate my method against that piece of hardware. > So it seems like your downlink doesn't work rather than uplink. Trust me, its the uplink which is not working. When I used LCR (through MISDN and chan_lcr) to hook OpenBSC to Asterisk, I was able to hear both the test music and a test tone, but the echo test was not working. When I left LCR and Asterisk out (just two mobiles calling each other) I was not able to hear anything. I am using normal Full Rate calls (no AMR, no EFR, no HR). Anyway is this the desired way to hook OpenBSC to Asterisk? I know LCR also have a SIP method to connect to Asterisk, but I never figured that out and have good experience with the MISDN method. > which branch are you testing with? For Osmo-BTS I used Fairwaves/master, for Osmo-TRX I used the master branch (the fiarwaves/master is still not compiling due to the compile time instruction set issue we identified a few weeks ago). I can try fairwaves/rebase for Osmo-BTS if you want. > I'd suggest checking that your uplink works I use RX gain 12, the MS TX power is limited to 20dBm and I also have a duplex filter. With this setup "show lchan" say the uplink is around -47dBm the downlink is around -67dBm. The TRX log does not indicate any saturation issue (or any other problems during the call). Will try and enable the extra logging and try to extract some meaningful information from that first, after that will try fairwaves/rebase. Thanks for your help! Regards, Csaba ----- Eredeti üzenet ----- Feladó: "Alexander Chemeris" <alexander.chemeris at gmail.com> Címzett: "Sipos Csaba" <sipos.csaba at kvk.uni-obuda.hu> Másolatot kap: "OpenBSC Mailing List" <openbsc at lists.osmocom.org> Elküldött üzenetek: Szombat, 2015. Szeptember 19. 20:09:54 Tárgy: Re: Half sided calls Hi Sipos, On Sat, Sep 19, 2015 at 5:05 PM, Sipos Csaba <sipos.csaba at kvk.uni-obuda.hu> wrote: > I am in the process of creating the Wiki page for Ettus B200/B210 with OpenBSC, GPRS and Asterisk. Any reason it's specific to B2x0? Configuration should be 99% common for all SDR devices and I think it makes more sense to have a single page for that, like the old network_from_scratch. > I am quite close, both data and calls are working, but the voice calls are half sided. The downlink direction works, but the uplink does not. > > I tried without Asterisk and LCR (between two phones) and still the calls are half sided. > > In the mean time I got these messages in the Osmo-BTS log: > > <0006> scheduler.c:276 PH-DATA.req: chan_nr=0x0a link_id=0x00 fn=1284768 ts=2 tr x=0 > <0006> scheduler.c:1036 TCH/F has not been served !! No prim for trx=0 ts=1 at f n=1284764 to transmit. > <0006> scheduler.c:1036 TCH/F has not been served !! No prim for trx=0 ts=2 at f n=1284764 to transmit. Log message suggests that downlink doesn't receive a frame from RTP side and thus transmits a filler frame. So it seems like your downlink doesn't work rather than uplink. It's not clear what do you mean that a call is half sided? According to the logs, downlink frames are not served at both timeslots, so you should not hear anything on both sides of the call. I'd suggest checking that your uplink works, e.g. by looking at osmo-trx logs. If you have the latest one, it should output a warning if Rx side is saturated, which is the most possible reason for the issue. Another possible issue is codec. I have tested only with GSM-FR so far. If you enable more debugging in osmo-bts, you should be able to see decoding result at least for gsm-fr codec. I recommend you enable at least NOTICE level for L1C and see if there are any fail messages from here: http://cgit.osmocom.org/osmo-bts/tree/src/osmo-bts-trx/gsm0503_coding.c?h=201509-fairwaves-rebase One more thing - which branch are you testing with? I've been testing 201509-fairwaves-rebase. If you're using something else - I'd be curious what happens if you try 201509-fairwaves-rebase. -- Regards, Alexander Chemeris. CEO, Fairwaves, Inc. https://fairwaves.co