This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/gerrit-log@lists.osmocom.org/.
laforge gerrit-no-reply at lists.osmocom.orglaforge has submitted this change. ( https://gerrit.osmocom.org/c/simtrace2/+/24519 )
Change subject: octsimtest: remove lots of unused #defines
......................................................................
octsimtest: remove lots of unused #defines
The octsimtest board only supports cardem mode, not 'ccid'
nor 'sniffer'. Remove related GPIO pin #defines from board.h
Change-Id: I43e8631d945ba183a1e5b1e37dd4565adb377154
---
M firmware/libboard/octsimtest/include/board.h
1 file changed, 0 insertions(+), 55 deletions(-)
Approvals:
Jenkins Builder: Verified
laforge: Looks good to me, approved
diff --git a/firmware/libboard/octsimtest/include/board.h b/firmware/libboard/octsimtest/include/board.h
index 2b8e7bf..a267f0f 100644
--- a/firmware/libboard/octsimtest/include/board.h
+++ b/firmware/libboard/octsimtest/include/board.h
@@ -50,33 +50,8 @@
/* Button to force bootloader start (shorted to ground when pressed */
#define PIN_BOOTLOADER_SW {PIO_PA5, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP}
-//FIXME SIM_PWEN_PIN collides with PA5/bootloader_sw on octsimtest
-/* Enable powering the card using the second 3.3 V output of the LDO (active high) */
-#define SIM_PWEN_PIN {PIO_PA12, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
-/* Enable powering the SIM card */
-#define PWR_PINS SIM_PWEN_PIN
-
// FIXME PA8 is 32khz xtal on octsimtest
-/* Card presence pin */
-#define SW_SIM PIO_PA11
/* Pull card presence pin high (shorted to ground in card slot when card is present) */
-#define SMARTCARD_CONNECT_PIN {SW_SIM, PIOA, ID_PIOA, PIO_INPUT, PIO_PULLUP | PIO_DEBOUNCE | PIO_DEGLITCH | PIO_IT_EDGE }
-
-/** Smart card connection **/
-//FIXME
-/* Card RST reset signal input (active low; RST_SIM in schematic) */
-#define PIN_SIM_RST {PIO_PA13, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
-/* Card I/O data signal input/output (I/O_SIM in schematic) */
-#define PIN_SIM_IO {PIO_PA6A_TXD0, PIOA, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT}
-/* Card CLK clock input (CLK_SIM in schematic) */
-#define PIN_SIM_CLK {PIO_PA2B_SCK0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
-/* Pin to measure card I/O timing (to start measuring the ETU on I/O activity; connected I/O_SIM in schematic) */
-#define PIN_SIM_IO_INPUT {PIO_PA1B_TIOB0, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
-//FIXME PIO_PA4B_TCLK0 PA4 is LED on octsimtest
-/* Pin used as clock input (to measure the ETU duration; connected to CLK_SIM in schematic) */
-#define PIN_SIM_CLK_INPUT {PIO_PA14, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
-/* Pins used to measure ETU timing (using timer counter) */
-#define PINS_TC PIN_SIM_IO_INPUT, PIN_SIM_CLK_INPUT
/** Phone connection **/
/* Phone USIM slot 1 VCC pin (VCC_PHONE in schematic) */
@@ -95,36 +70,6 @@
#define PIN_PHONE_CLK_INPUT {PIO_PA29B_TCLK2, PIOA, ID_PIOA, PIO_PERIPH_B, PIO_DEFAULT}
/** Default pin configuration **/
-/* Disconnect VPP, CLK, and RST lines between card and phone using bus switch (high sets bus switch to high-impedance) */
-#define PIN_SC_SW_DEFAULT {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
-/* Disconnect I/O line between card and phone using bus switch (high sets bus switch to high-impedance) */
-#define PIN_IO_SW_DEFAULT {PIO_PA19, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
-/* Disconnect all lines (VPP, CLK, RST, and I/O) between card and phone */
-#define PINS_BUS_DEFAULT PIN_SC_SW_DEFAULT, PIN_IO_SW_DEFAULT
-
-/** Sniffer configuration **/
-/* Connect VPP, CLK, and RST lines between card and phone using bus switch (low connects signals on bus switch) */
-#define PIN_SC_SW_SNIFF {PIO_PA20, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
-/* Connect I/O line between card and phone using bus switch (low connects signals on bus switch) */
-#define PIN_IO_SW_SNIFF {PIO_PA19, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
-/* Connect all lines (VPP, CLK, RST, and I/O) between card and phone */
-#define PINS_BUS_SNIFF PIN_SC_SW_SNIFF, PIN_IO_SW_SNIFF
-/* Card RST reset signal input (use as input since the phone will drive it) */
-#define PIN_SIM_RST_SNIFF {PIO_PA7, PIOA, ID_PIOA, PIO_INPUT, PIO_DEGLITCH | PIO_IT_EDGE}
-/* Pins used to sniff phone-card communication */
-#define PINS_SIM_SNIFF PIN_SIM_IO, PIN_SIM_CLK, PIN_SIM_RST_SNIFF
-/* Disable power converter 4.5-6V to 3.3V (active high) */
-#define PIN_SIM_PWEN_SNIFF {SIM_PWEN, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
-/* Enable power switch to forward VCC_PHONE to VCC_SIM (active high) */
-#define PIN_VCC_FWD_SNIFF {VCC_FWD, PIOA, ID_PIOA, PIO_OUTPUT_1, PIO_DEFAULT}
-/* Use phone VCC to power card */
-#define PINS_PWR_SNIFF PIN_SIM_PWEN_SNIFF, PIN_VCC_FWD_SNIFF
-
-/** CCID configuration */
-/* Card RST reset signal input (active low; RST_SIM in schematic) */
-#define PIN_ISO7816_RSTMC {PIO_PA7, PIOA, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT}
-/* ISO7816-communication related pins */
-#define PINS_ISO7816 PIN_SIM_IO, PIN_SIM_CLK, PIN_ISO7816_RSTMC // SIM_PWEN_PIN, PIN_SIM_IO2, PIN_SIM_CLK2
/** External SPI flash interface **/
/* SPI MISO pin definition */
--
To view, visit https://gerrit.osmocom.org/c/simtrace2/+/24519
To unsubscribe, or for help writing mail filters, visit https://gerrit.osmocom.org/settings
Gerrit-Project: simtrace2
Gerrit-Branch: master
Gerrit-Change-Id: I43e8631d945ba183a1e5b1e37dd4565adb377154
Gerrit-Change-Number: 24519
Gerrit-PatchSet: 1
Gerrit-Owner: laforge <laforge at osmocom.org>
Gerrit-Reviewer: Jenkins Builder
Gerrit-Reviewer: laforge <laforge at osmocom.org>
Gerrit-MessageType: merged
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.osmocom.org/pipermail/gerrit-log/attachments/20210603/ba667aeb/attachment.htm>