This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/gerrit-log@lists.osmocom.org/.
laforge gerrit-no-reply at lists.osmocom.orglaforge has submitted this change. ( https://gerrit.osmocom.org/c/osmo-bsc/+/19328 ) Change subject: {bts,bsc}.adoc: Drop deprecated OsmoNITB references ...................................................................... {bts,bsc}.adoc: Drop deprecated OsmoNITB references dyn_ts_allow_tch_f is also deprecated and should not be used, so drop that too. Change-Id: Icc91dd41a237531cb512fa36d8b18d4d8d5ca8ed --- M doc/manuals/chapters/bsc.adoc M doc/manuals/chapters/bts.adoc 2 files changed, 8 insertions(+), 14 deletions(-) Approvals: Jenkins Builder: Verified Hoernchen: Looks good to me, but someone else must approve laforge: Looks good to me, approved diff --git a/doc/manuals/chapters/bsc.adoc b/doc/manuals/chapters/bsc.adoc index 49d25e5..0d3ded5 100644 --- a/doc/manuals/chapters/bsc.adoc +++ b/doc/manuals/chapters/bsc.adoc @@ -1,9 +1,5 @@ == BSC level configuration -The BSC component is shared between OsmoBSC and OsmoNITB. This chapter -describes some of the configuration options related to this shared BSC -component. - === Hand-over ==== Hand-over in GSM @@ -25,11 +21,10 @@ The hand-over decision is made by an algorithm that processes those measurement results and determines when to perform the hand-over. -==== Configuration of hand-over in OsmoBSC/OsmoNITB +==== Configuration of hand-over in OsmoBSC -OsmoBSC (like the internal BSC component of OsmoNITB) only support -so-called intra-BSC hand-over, where the hand-over is performed between -two BTSs within the same BSC. +OsmoBSC only support so-called intra-BSC hand-over, where the hand-over is +performed between two BTSs within the same BSC. Hand-over is enabled and configured by the use of a set of `handover` commands. Using those, you can tune the key parameters of the hand-over diff --git a/doc/manuals/chapters/bts.adoc b/doc/manuals/chapters/bts.adoc index 223cec1..94e89a4 100644 --- a/doc/manuals/chapters/bts.adoc +++ b/doc/manuals/chapters/bts.adoc @@ -287,9 +287,9 @@ the BTS needs to be ensured, any MSC is compatible with dynamic timeslots by definition. -OsmoBSC and OsmoNITB support two kinds of dynamic timeslot handling, configured -via the `network` / `bts` / `trx` / `timeslot` / `phys_chan_config` -configuration. Not all BTS models support dynamic channels. +OsmoBSC supports two kinds of dynamic timeslot handling, configured via the +`network` / `bts` / `trx` / `timeslot` / `phys_chan_config` configuration. Not +all BTS models support dynamic channels. [[dyn_ts_compat]] .Dynamic timeslot support by various BTS models @@ -349,9 +349,8 @@ ==== Dynamic Timeslot Configuration Examples -This is an extract of an `osmo-bsc` or `osmo-nitb` config file. A timeslot -configuration with five Osmocom style dynamic timeslots and one dedicated PDCH -may look like this: +This is an extract of an `osmo-bsc`` config file. A timeslot configuration with +five Osmocom style dynamic timeslots and one dedicated PDCH may look like this: ---- network -- To view, visit https://gerrit.osmocom.org/c/osmo-bsc/+/19328 To unsubscribe, or for help writing mail filters, visit https://gerrit.osmocom.org/settings Gerrit-Project: osmo-bsc Gerrit-Branch: master Gerrit-Change-Id: Icc91dd41a237531cb512fa36d8b18d4d8d5ca8ed Gerrit-Change-Number: 19328 Gerrit-PatchSet: 2 Gerrit-Owner: pespin <pespin at sysmocom.de> Gerrit-Reviewer: Hoernchen <ewild at sysmocom.de> Gerrit-Reviewer: Jenkins Builder Gerrit-Reviewer: laforge <laforge at osmocom.org> Gerrit-MessageType: merged -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.osmocom.org/pipermail/gerrit-log/attachments/20200721/59946bc9/attachment.htm>