Change in osmo-ccid-firmware[master]: remove SWO pin initialisation

Kévin Redon gerrit-no-reply at lists.osmocom.org
Tue Apr 16 23:29:21 UTC 2019


Kévin Redon has uploaded this change for review. ( https://gerrit.osmocom.org/13674


Change subject: remove SWO pin initialisation
......................................................................

remove SWO pin initialisation

Change-Id: I199d6e356129526e65d5d1075a264eb35904d099
---
M sysmoOCTSIM/driver_init.c
1 file changed, 0 insertions(+), 47 deletions(-)



  git pull ssh://gerrit.osmocom.org:29418/osmo-ccid-firmware refs/changes/74/13674/1

diff --git a/sysmoOCTSIM/driver_init.c b/sysmoOCTSIM/driver_init.c
index 0d5bb53..8a50925 100644
--- a/sysmoOCTSIM/driver_init.c
+++ b/sysmoOCTSIM/driver_init.c
@@ -723,53 +723,6 @@
 
 	gpio_set_pin_function(SDA1, GPIO_PIN_FUNCTION_OFF);
 
-	// GPIO on PB30
-
-	gpio_set_pin_direction(UART_TX,
-	                       // <y> Pin direction
-	                       // <id> pad_direction
-	                       // <GPIO_DIRECTION_OFF"> Off
-	                       // <GPIO_DIRECTION_IN"> In
-	                       // <GPIO_DIRECTION_OUT"> Out
-	                       GPIO_DIRECTION_OUT);
-
-	gpio_set_pin_level(UART_TX,
-	                   // <y> Initial level
-	                   // <id> pad_initial_level
-	                   // <false"> Low
-	                   // <true"> High
-	                   false);
-
-	gpio_set_pin_pull_mode(UART_TX,
-	                       // <y> Pull configuration
-	                       // <id> pad_pull_config
-	                       // <GPIO_PULL_OFF"> Off
-	                       // <GPIO_PULL_UP"> Pull-up
-	                       // <GPIO_PULL_DOWN"> Pull-down
-	                       GPIO_PULL_OFF);
-
-	gpio_set_pin_function(UART_TX,
-	                      // <y> Pin function
-	                      // <id> pad_function
-	                      // <i> Auto : use driver pinmux if signal is imported by driver, else turn off function
-	                      // <GPIO_PIN_FUNCTION_OFF"> Auto
-	                      // <GPIO_PIN_FUNCTION_OFF"> Off
-	                      // <GPIO_PIN_FUNCTION_A"> A
-	                      // <GPIO_PIN_FUNCTION_B"> B
-	                      // <GPIO_PIN_FUNCTION_C"> C
-	                      // <GPIO_PIN_FUNCTION_D"> D
-	                      // <GPIO_PIN_FUNCTION_E"> E
-	                      // <GPIO_PIN_FUNCTION_F"> F
-	                      // <GPIO_PIN_FUNCTION_G"> G
-	                      // <GPIO_PIN_FUNCTION_H"> H
-	                      // <GPIO_PIN_FUNCTION_I"> I
-	                      // <GPIO_PIN_FUNCTION_J"> J
-	                      // <GPIO_PIN_FUNCTION_K"> K
-	                      // <GPIO_PIN_FUNCTION_L"> L
-	                      // <GPIO_PIN_FUNCTION_M"> M
-	                      // <GPIO_PIN_FUNCTION_N"> N
-	                      GPIO_PIN_FUNCTION_H);
-
 	// GPIO on PC00
 
 	// Set pin direction to input

-- 
To view, visit https://gerrit.osmocom.org/13674
To unsubscribe, or for help writing mail filters, visit https://gerrit.osmocom.org/settings

Gerrit-Project: osmo-ccid-firmware
Gerrit-Branch: master
Gerrit-MessageType: newchange
Gerrit-Change-Id: I199d6e356129526e65d5d1075a264eb35904d099
Gerrit-Change-Number: 13674
Gerrit-PatchSet: 1
Gerrit-Owner: Kévin Redon <kredon at sysmocom.de>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.osmocom.org/pipermail/gerrit-log/attachments/20190416/a782ba3b/attachment.html>


More information about the gerrit-log mailing list